11

I'm running RHEL 6.4, kernel-2.6.32-358.el6.i686, on an HP ML 350 G5 with two onboard Broadcom NetXtreme II BCM5708 1000Base-T NICs. My goal is to channel bond the two interfaces into a mode=1 failover pair.

My problem is that in spite of all evidence that the bond is set up and accepted, pulling the cable out of the primary NIC causes all communication to cease.

ifcfg-etho and ifcfg-eth1

First, ifcfg-eth0:

DEVICE=eth0
HWADDR=00:22:64:F8:EF:60
TYPE=Ethernet
UUID=99ea681d-831b-42a7-81be-02f71d1f7aa0
ONBOOT=yes
NM_CONTROLLED=yes
BOOTPROTO=none
MASTER=bond0
SLAVE=yes

Next, ifcfg-eth1:

DEVICE=eth1
HWADDR=00:22:64:F8:EF:62
TYPE=Ethernet
UUID=92d46872-eb4a-4eef-bea5-825e914a5ad6
ONBOOT=yes
NM_CONTROLLED=yes
BOOTPROTO=none
MASTER=bond0
SLAVE=yes

ifcfg-bond0

My bond's config file:

DEVICE=bond0
IPADDR=192.168.11.222
GATEWAY=192.168.11.1
NETMASK=255.255.255.0
DNS1=192.168.11.1
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
BONDING_OPTS="mode=1 miimmon=100"

/etc/modprobe.d/bonding.conf

I have an /etc/modprobe.d/bonding.conf file that is populated thusly:

alias bond0 bonding

ip addr output

The bond is up and I can access the server's public services through the bond's IP address:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP qlen 1000
    link/ether 00:22:64:f8:ef:60 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master bond0 state UP qlen 1000
    link/ether 00:22:64:f8:ef:60 brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP 
    link/ether 00:22:64:f8:ef:60 brd ff:ff:ff:ff:ff:ff
    inet 192.168.11.222/24 brd 192.168.11.255 scope global bond0
    inet6 fe80::222:64ff:fef8:ef60/64 scope link 
       valid_lft forever preferred_lft forever

Bonding Kernel Module

...is loaded:

# cat /proc/modules | grep bond
bonding 111135 0 - Live 0xf9cdc000

/sys/class/net

The /sys/class/net filesystem shows good things:

cat /sys/class/net/bonding_masters 
bond0
cat /sys/class/net/bond0/operstate 
up
cat /sys/class/net/bond0/slave_eth0/operstate 
up
cat /sys/class/net/bond0/slave_eth1/operstate 
up
cat /sys/class/net/bond0/type 
1

/var/log/messages

Nothing of concern appears in the log file. In fact, everything looks rather happy.

Jun 15 15:47:28 rhsandbox2 kernel: Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: setting mode to active-backup (1).
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: setting mode to active-backup (1).
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: setting mode to active-backup (1).
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: setting mode to active-backup (1).
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: Adding slave eth0.
Jun 15 15:47:28 rhsandbox2 kernel: bnx2 0000:03:00.0: eth0: using MSI
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: making interface eth0 the new active one.
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: first active interface up!
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: enslaving eth0 as an active interface with an up link.
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: Adding slave eth1.
Jun 15 15:47:28 rhsandbox2 kernel: bnx2 0000:05:00.0: eth1: using MSI
Jun 15 15:47:28 rhsandbox2 kernel: bonding: bond0: enslaving eth1 as a backup interface with an up link.
Jun 15 15:47:28 rhsandbox2 kernel: 8021q: adding VLAN 0 to HW filter on device bond0
Jun 15 15:47:28 rhsandbox2 kernel: bnx2 0000:03:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex
Jun 15 15:47:28 rhsandbox2 kernel: bnx2 0000:05:00.0: eth1: NIC Copper Link is Up, 1000 Mbps full duplex

So what's the problem?!

Yanking the network cable from eth0 causes all communication to go dark. What could the problem be and what further steps should I take to troubleshoot this?

EDIT:

Further Troubleshooting:

The network is a single subnet, single VLAN provided by a ProCurve 1800-8G switch. I have added primary=eth0 to ifcfg-bond0 and restart networking services, but that has not changed any behavior. I checked /sys/class/net/bond0/bonding/primary both before and after adding primary=eth1 and it has a null value, which I'm not sure is good or bad.

Tailing /var/log/messages when eth1 has its cable removed shows nothing more than:

Jun 15 16:51:16 rhsandbox2 kernel: bnx2 0000:03:00.0: eth0: NIC Copper Link is Down
Jun 15 16:51:24 rhsandbox2 kernel: bnx2 0000:03:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex

I added use_carrier=0 to ifcfg-bond0's BONDING_OPTS section to enables the use of MII/ETHTOOL ioctls. After restarting the network service, there was no change in symptoms. Pulling the cable from eth0 causes all network communication to cease. Once again, no errors in /var/log/messages save for the notification that the link on that port went down.

3
  • 1
    Can you add some more information such as make/model switch connected to, any VLAN setup on switch, bond slave states and /var/log/messages after the cable to eth0 is unplugged?
    – Andy Shinn
    Jun 15, 2013 at 23:30
  • @AndyShinn The switch that it is directly connected to is a ProCurve 1800-8G. There are no VLANs on the network. It's a simple single subnet, single VLAN network.
    – Wesley
    Jun 15, 2013 at 23:34
  • @AndyShinn Ah, and also the bond slave states are both reported as up. Tailing /var/log/messages at the time of eth0 being unplugged only shows that the copper link has been unplugged. No messages from the bonding module.
    – Wesley
    Jun 15, 2013 at 23:53

3 Answers 3

21

READ. YOUR. CONFIGS.

And when that fails...

READ. ALL. OUTPUTS.

Do you see what's in ifcfg-bond0? No, do you understand what's in ifcfg-bond0?
What in the world of slippery penguins is miimmon=100?
Oh I'm sorry, did you mean miimon=100?

Yeah, I think you meant miimon and not miimmon.

Also, a big giveaway is that when you restart your network service you see this:

service network restart
Shutting down interface bond0:                             [  OK  ]
Shutting down loopback interface:                          [  OK  ]
Bringing up loopback interface:                            [  OK  ]
Bringing up interface bond0:  ./network-functions: line 446: /sys/class/net/bond0/bonding/miimmon: No such file or directory
./network-functions: line 446: /sys/class/net/bond0/bonding/miimmon: No such file or directory
                                                           [  OK  ]

Pay careful attention to everything you type and when you make your inevitable typing mistake, pay careful attention to every output that you see.

You are a bad person and you should feel bad.

1
  • 8
    BAD CAT! sprays with hose
    – voretaq7
    Jun 16, 2013 at 4:45
2

Try specifying one of the NICS as the primary slave.

DEVICE=bond0
IPADDR=192.168.11.222
GATEWAY=192.168.11.1
NETMASK=255.255.255.0
DNS1=192.168.11.1
ONBOOT=yes
BOOTPROTO=none
USERCTL=no
BONDING_OPTS="mode=1 miimmon=100 primary=eth0"

More documentation from RH:

primary= Specifies the interface name, such as eth0, of the primary device. The primary device is the first of the bonding interfaces to be used and is not abandoned unless it fails. This setting is particularly useful when one NIC in the bonding interface is faster and, therefore, able to handle a bigger load. This setting is only valid when the bonding interface is in active-backup mode. Refer to /usr/share/doc/kernel-doc-/Documentation/networking/bonding.txt for more information.

3
  • Before I edited ifcfg-bond0 I checked /sys/class/net/bond0/bonding/primary and the response is blank. I added primary=eth0 to ifcfg-bond0 and restart the network service. There is no change in the symptom and no change to /sys/class/net/bond0/bonding/primary Thanks for the suggestion though!
    – Wesley
    Jun 15, 2013 at 23:33
  • try adding use_carrier=0 ? see above RH doc for details
    – dmourati
    Jun 15, 2013 at 23:37
  • Done - added the information to the question. There was no change in behavior, but that's a good option to know about.
    – Wesley
    Jun 16, 2013 at 0:03
2

Add the following bonding option downdelay=xxxx in milisec that fails a eth after it has been detected as failed and set the primary slave to the remaining. If this parameter is not in the bonding_opt, the bond detecte the failure (because you include miimom=yyyy) but it never fails the eth0. You can see this happening by looking at the /proc/net/bonding/bondX file.

Anyway, with RHEL 6.3 (almost the same version as yours) we are having several other problems with bonding related to failing back, duplicated mac addr seen from the switch.

good luck.

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .