Is it possible to "roughly" approximate the amount of time chkdsk will take on Windows Server 2003?

Question

I know there are a number of variables at play with this question... so I'm just looking for an approximation. Is it possible to calculate the amount of time a 'chkdsk' will take for a Windows Server 2003 platform? In this specific case I'm using a RAID1 set of two 1TB drives. My real goal here is to attempt to plan a maintenance window for the platform. I'm kinda thinking that if the drive speed and capacity is known; some super genius out there can guesstimate the amount of time a 'chkdsk' on boot will take.

In my, albeit impatient, google searching I found a number of discussions of the different flags and what they do. I'm fully aware of them. I'm just none too sure of the time it would take - will it be 20 hours? will it be 4 hours? will it be 72 hours? Is it even possible to approximate this?

Answer 1

I had a volume with millions of very small files which was about 1TB in size and after 8 or so hours we killed it. It was like 5% done. But the more files the longer it'll take.

Answer 2

Microsoft has an article explaining chkdsk on their help and support website. The article suggests running in read-only mode. To run read-only run chkdsk on the disk without any switches. The article also states that the more files and folders you have the longer the run will take. Files and folders are more important than volume size.

Paragraph 15 of the article above discusses this and some of the problems associated with running in read-only mode.

The best way to guesstimate is a trial run and then add time to it. Good luck.

Answer 3

It is standard to keep the operating system and data files on seperate partitions. Your C:\ (Windows) partition is typically 80-300GB, while the data partition is larger. If you follow this convention, you should be able to chkdsk the data volume "online" with no downtime. If a problem does crop up, I would set aside a reasonable maintenance window of atleast 8 hours, but it might take <30 minutes to fully run. A clean 1TB volume should check disk in <5 minutes. A very dirty one might take much longer. I would be concerned if it took longer than an hour.

Answer 4

This does not answer the question but might help in reducing time needed for chkdsk on a new build...

Time taken for chkdsk will also be a function of allocation unit size. Larger units take less time to check because there are fewer of them on the same disk - there is less "metadata" to be checked.

If you know the drive will hold mostly larger files it may be good to format with a larger au size (than the 4 KB default) even though you will waste on average (half an au) * (# of files on the disk). Defragmentation will also be less severe for the same reasons.

On some disk arrays it is also important to offset the starting address of a new partition so it is correctly aligned on "disk" or "cache" boundaries.

Answer 5

If running chkdsk with /r on 600GB of data, I would think it would be in the 5-6 hour range. Obviously there are quite a few more variables involved but I'd say thats a starting point.

Answer 6

If you run chkdsk /r on a large drive (that's quite full) you are best off just going to bed, it will be ready when you wake up. This technique has worked for me in the past.

Answer 7

basic timing scheme is as followed. over 1 minute record how many files per minute it processed. For example 3000/60s. Subtract completed from the total then divide that by 3k from the files left, this will get you how many minutes till completion. Divide your minutes by 60 to get hours. ta-dah. for example

22 percent complete. (156046 if 804592 files processed) @ roughly 3000 per minute

3000/60s

804592-156046 = 648546 files

648546/3000 = 216.182 minutes

216.182/60 = 3.603033 hours .60 = to 60% of an hour

60 minutes x .60 = 36 minutes

so 3 hours and 36 minutes till finished

this is a rough estimate not accounting for the chkdsk running into bad sectors or locking up. Please excuse my poor math skills, I'm sure there is someway to turn this into an equation to express this better as a formula.

Answer 8

just for an idea im running windows 10 home I7 quad 1 tb hdd 5400rpm , 8 gb ram the hdd is 1\3 full around 300gb took about 4 hr to do chkdsk /r c:

Answer 9

I started 22 hours ago on a 3TB drive that is 80% full. It states 10% done but I know from experience that the 10% can turn to 90 % real quick. In fact it has been at 10% for at least 20 of the 22 hours. Once it gets to files that do not have bad clusters the % will increase much quicker.