4

Has installed a system (rhel-server-6.4-x86_64-dvd.iso). KVM over which set. The host machine and the guest-machine assigned its own IP-address, configured for this bridge br0. Everything works. Now we must make a bridge over bonding.

Put on the host the following settings:

[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 
DEVICE=eth0
HWADDR=f0:92:1c:0f:76:f8
MASTER=bond0
SLAVE=yes
ONBOOT=yes

[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
DEVICE=eth1
HWADDR=F0:92:1C:0F:76:FC
MASTER=bond0
SLAVE=yes
ONBOOT=yes

[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-bond0 
DEVICE=bond0
ONBOOT=yes
BRIDGE="br0"

[root@server ~]# cat /etc/modprobe.conf 
alias bond0 bonding
options bond0 mode=1 miimon=100

[root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-br0 
DEVICE="br0"
NM_CONTROLLED="no"
ONBOOT="yes"
TYPE="Bridge"
BOOTPROTO="static"
IPADDR="10.2.26.39"
GATEWAY="10.2.26.1"
MTU="1500"
NETMASK="255.255.255.0"
DEFROUTE="yes"
IPV4_FAILURE_FATAL="yes"
IPV6INIT="no"
NAME="System br0"

Check out:

[root@server ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth0
MII Status: down
Speed: Unknown
Duplex: Unknown
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:76:f8
Slave queue ID: 0

Slave Interface: eth1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:76:fc
Slave queue ID: 0

eth0 was down for. Although I was expecting to see something like the following:

[root@server ~]# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0

Slave Interface: eth0
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:d5:e8
Slave queue ID: 0

Slave Interface: eth1
MII Status: up
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 0
Permanent HW addr: f0:92:1c:0f:d5:ec
Slave queue ID: 0

The question itself in a subject, how to configure bridge over bonding in RHEL 6.4 Server?

1 Answer 1

1

This is the correct configuration, though a couple of points:

  • You don't need to alias bond0 bonding at all
  • Bonding configuration should be as BONDING_OPTS in the ifcfg-bondX, not in modprobe
  • Add a DELAY=0 to your bridge, to prevent it waiting on interface start

The fact that eth0 is down has nothing to do with bridging or bonding, troubleshoot the physical interface. ethtool eth0 will show you it has no link detected.

Reseat the cable, replace the cable, try a different switchport, try a different NIC.

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .