Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

I need to build a server which is capable of capturing 20 Gigabit/second network traffic (2 x 10g network adapters - 99% utilization) and store them on a disk with zero packet-lose. The requirements is supply the ability to record 20-30 minutes of continues traffic.

Not being an “Hardware Expert”, I have search the net for today’s fastest hard drives and came up with the following option: Setting Raid-0 (stripe) over 6 x 600 GB WD’s VelociRaptor SATA drives, which claim to be the fastest (sata) drive on earth (6 Gb/s interface) - that would provide 36Gbps writing speed.

My questions are basically, having the hard drive spot sorted out,

  1. What about the other parts of the machine, what kind of a motherboard would I need?
  2. What kind of a CPU?
  3. How many CPUs?
  4. How much RAM is needed given the fact data is not manipulated but written into the hard drives?

I would like to thank you all in advance for your help and advises.

share|improve this question
Just because the sta link is 6 Gb/s doesn't mean the drive will actually write at that speed. That is basically the speed between the computer and the cache, not the actually drive. If you check the actual spec sheet you will see that the maximum sustained write transfer speed is 145 MB/s. So those 6 drives really only give you about 7Gb/s –  Zoredache Aug 10 '10 at 17:09
@zoredache you are 100% right. I am going back to the drawing board (rephrasing the question) –  Tzury Bar Yochay Aug 10 '10 at 17:18
How long do you want to store your data? How about reading from it? Your 6x 600G drives in RAID-0 have 3.6TB of space, and you're writing out 2.5GB/s, meaning you'll only store 24 minutes (!) of data. Then, assume it all works, you'll want to read it. Well, your disk bandwidth is saturated with writes, no time to read (without losing data)... –  Bill Weiss Aug 10 '10 at 18:30
Mechanical drive write performance drops considerably as you reach the end of the disk. See the graph on slide 6 at cacetech.com/sharkfest.10/… –  Gerald Combs Aug 10 '10 at 18:50
@Bill when I write, I only writes. Read is to be done later on, but at that time, no writes is active –  Tzury Bar Yochay Aug 11 '10 at 2:59
show 1 more comment

1 Answer

While I have my doubts about how realistic this sort of thing is with OTS hardware; here's my thoughts:

Each of those drives can do about 1Gbps (max); you'd need an array of at least 20 to get the write performance you need. Realistically you'd probably need upwards of 30 drives to get continuous throughput and some kind of redundancy; though I don't think there's many SAS RAIDs that can do 2.5GBps with RAID5 or 6; so you might be stuck with RAID10.

You'll need 3 to 4.5 TB of usable storage for that much data. With the Raptor drives you'll easily have that much, even with RAID10 (which is probably your best choice here).

The CPU, PCIe lanes, and RAM shouldn't be too much consideration; other than whatever the RAID Card and NICs need. I'd get a fast CPU before one with a lot of cores. It's not doing much itself, just coordinating DMA transfers for the most part. I'd grab at least 4GB of RAM; though more is pretty much going to be better all around.

share|improve this answer
chris, I just sent you an email at comcast, see inline ;-) –  Tzury Bar Yochay Aug 10 '10 at 17:40
You might be able to get away with less hardware if you take a look at solid state drives. You can get get much faster the write speed with SSD, of course at a much greater cost. –  Zoredache Aug 10 '10 at 17:47
@zoredache, I did check that option, especially this one [1]. However, the fact I cannot build a raid from several of them, that is from all disks available at two or three pci-express boards eliminate that option [1] ocztechnology.com/products/solid-state-drives/pci-express/… –  Tzury Bar Yochay Aug 10 '10 at 17:53
@chris, would not raid 0 perform better than raid 10? –  Tzury Bar Yochay Aug 10 '10 at 17:54
@Tzury, RAID0 would be faster than RAID10; I assumed you wanted some sort of continuity in the case of failure (which is getting somewhat likely with the number of drives). –  Chris S Aug 10 '10 at 19:13
show 1 more comment

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.