Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

So let's say I have a network of less than 20 computers including a server that needs to be accessed externally. What router/firewall solutions would you recommend? It can be either hardware or software and would need to be able to do

  • NAT
  • Firewall
  • DMZ
  • Native VPN if possible
  • Some form of network bandwidth monitoring

Update: I've accepted the answer I liked but this question probably doesn't have a definitive answer, it would depend on your requirements. Please leave more suggestions with an explanation as to why it works well in your situation.

share|improve this question

closed as not constructive by Chris S Jan 26 '12 at 5:07

As it currently stands, this question is not a good fit for our Q&A format. We expect answers to be supported by facts, references, or expertise, but this question will likely solicit debate, arguments, polling, or extended discussion. If you feel that this question can be improved and possibly reopened, visit the help center for guidance.If this question can be reworded to fit the rules in the help center, please edit the question.

    
I suggest making this question a community wiki then. We can compile a big list. –  gyaresu May 13 '09 at 2:30
    
Good point, done! –  Glenn Slaven May 13 '09 at 4:59
add comment

13 Answers

up vote 8 down vote accepted

We've been using pfSense running on WRAP/ALIX boards from pcengines for quite a while. I like the pcengines boards because they are small and low power, but you can use any old PC. Cheap and been trouble-free.

share|improve this answer
    
I second this. I've been running pfSense/monowall for over 3 years and find them to be way better than most commercial or free offerings. Where as m0n0wall is for embedded systems, pfsense is fully featured –  jdiaz May 1 '09 at 4:07
add comment

It sounds like a router/firewall Linux distribution would serve you just fine. http://en.wikipedia.org/wiki/List_of_Linux_router_or_firewall_distributions

share|improve this answer
add comment

I would highly recommend the Cisco 5505 ASA firewall. WebVPN, DMZ, POE port and it's even got Intrusion Prevention with an SSC card. The ASDM interface is super simple to set up. You no longer have to understand CLI completely to set up a Cisco product. A 50 user ASA from CDW is around $600.

I also believe that with the latest release of the ASA software, they will support NetFlow which will give you bandwidth stats.

share|improve this answer
add comment

I am a big fan of the Netgear ProSafe series.

These devices are so inexpensive that you can literally buy two and just keep one lying around just in case.

The VPN configuration is the easiest I've seen. I can ship out an FVS114 to a non-technical remote employee and they can be up and running with a hardware VPN in minutes.

If you have the money for it, a Cisco ASA is the way to go, but if you're on a budget, these little puppies do the trick.

share|improve this answer
add comment

If you don't want to spend much money take a look at DD-WRT or OpenWRT. Both are Linux based operating systems that if installed on a commercial router can make it preform like one worth ten times as much.

Both offer features or plugins that can do NAT, Firewall, DMZ, Native (open) VPN, Network Monitoring, and much more.

But they do not support all routers, be sure to look on their list of supported devices along with the notes for how to install it on your device.

share|improve this answer
add comment

Software wise, a small linux box with 3 network cards (internal, external, DMZ) is all you need. I'd reccommend smoothwall if you don't have much experience with Linux.

If you want a hardware solution, then I'd recommend Linksys which will be more than capable of 20-30 PCs (depending on your net connection you may need a separate modem). If you're moving into the 50+ range or need rock solid stability, then a low-end Cisco router is your best bet. There are a number of entry-level units available for under $500

share|improve this answer
    
Can the 3 cards be replaced with a single card and a small switch? –  Joe Philllips May 1 '09 at 2:42
    
Well... you're playing with fire then. You want to isolate the networks, otherwise savvy or incompetent users could screw things up. Plus smoothwall is designed to work with three interfaces, you can't do any proper bandwidth monitoring otherwise. –  saschabeaumont May 1 '09 at 2:51
1  
If you want to use one card, you'd really want to run VLAN trunking on it. At which point you're using a managed switch, and it would have been cheaper and easier to just get three cards (or possibly even a dual- or quad-port card...) –  derobert May 1 '09 at 3:38
    
@derobert good point, I didn't think about a managed switch. I still maintain it's cheaper/easier/safer to isolate the networks physically, VLAN trunking is overkill for 20 PC's ;) –  saschabeaumont May 1 '09 at 4:47
add comment

Been running m0n0wall for over a year now and it has proven to be quite a good solution. Lightweight, live monitoring chart for bandwidth and QoS management, things which IPCop (which I was using previously) was missing.

share|improve this answer
add comment

The Cisco 871w is a phenomeninal SOHO router that does everything you've required and more.

share|improve this answer
add comment

The Linux solutions mentioned here can certainly work fine if you are comfortable with them and in maintaining them. If you like out of the box solutions that are fairly affordable, I would go with SonicWall. They are easy to manage, fairly cost effective, and meet all of your needs. At about the same level is Zywall. It offers some more functionality, but the interface isn't as easy as SonicWall's. Support wise I would say both companies are on the same level, about average. For Linux based solutions, support can be had from numerous places. I would caution on the low end (Linksys) side for business applications for the size network you mention, in my experience their hardware is cheap, but you get what you pay for. Good luck!

share|improve this answer
add comment

Juniper Netscreen SSG5. Comes in wired and wireless flavours.

If you need ADSL, T1, E1 cards, the SSG20 has you covered. Also has a wireless option.

share|improve this answer
add comment

For hardware solutions I rely on Netopia. There Enterprise class routers are highly configurable, and are almost as easy to manage as Linksys (albeit via Telnet) and yet powerful enough to offer site-to-site connectors, multiple public ips, filter rules, etc.

They offer wired and wireless, with DSL modem and without. Check out the 3000 series...

share|improve this answer
add comment

If you only need ethernet interfaces on the router a snapgear firewall (I use the SG560) would do the job. I know it can do points 1-4 on your list.

If you put a dsl modem in bridged mode on the wan side it can also initiate PPPoE sessions.

At it's core it is a linux box with a nice web gui. There is a telnet and ssh interface but that is completely undocumented. One gotcha with the Snapgear is that all changes are live and automatically saved. So you can't use a "reboot in 10" like you can on a cisco to get you out of trouble if you lock yourself out when working on the firewall rulesets.

share|improve this answer
add comment

I've come to love Mikrotik routers for small scale office work - they are basically an embedded linux device with up to 9 network cards and the full power of iptables.

This is only a good choice if you are familiar with the basic of iptables; the GUI interface is a frontend to the linux features instead of being something designed for ease of use over functionality.

share|improve this answer
add comment

Not the answer you're looking for? Browse other questions tagged or ask your own question.