Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with.

I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server.

So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful.

I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80

Which is successful.

I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked).

I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access.

I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me.

Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production.

: Saved
:
ASA Version 8.2(4) 
!
hostname QG
domain-name XX.com
enable password
passwd
names
!
interface Ethernet0/0
 switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
 nameif inside
 security-level 100
 ip address 192.168.1.1 255.255.255.0 
!
interface Vlan2
 nameif outside
 security-level 0
 ip address XX.XX.XX.148 255.255.255.0 
!
interface Vlan3
 shutdown
 no forward interface Vlan1
 nameif dmz
 security-level 50
 ip address dhcp 
!
boot system disk0:/asa824.bin
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
 domain-name fw.XXgroup.com
same-security-traffic permit inter-interface
access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www 
access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https 
access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www 
access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https 
access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www 
access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any 
access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-635.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 
static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 
access-group acl-outside in interface outside
route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authorization command LOCAL 
http server enable
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac 
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set pfs group1
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
 authentication crack
 encryption 3des
 hash sha
 group 2
 lifetime 86400
no crypto isakmp nat-traversal
client-update enable
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.2-192.168.1.33 inside
dhcpd dns 208.77.88.4 interface inside
dhcpd enable inside
!

threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
 enable outside
 svc image disk0:/sslclient-win-1.1.0.154.pkg 1
 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2
 svc enable
group-policy ATSAdmin internal
group-policy ATSAdmin attributes
 dns-server value 208.77.88.4 208.85.174.9
 vpn-tunnel-protocol IPSec svc webvpn
 webvpn
  url-list none
  svc keep-installer installed
  svc rekey method ssl
  svc ask enable
username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15
username benl password 0HNIGQNI0uruJvhW encrypted privilege 0
username benl attributes
 vpn-group-policy ATSAdmin
username kuzma password rH7MM7laoynyvf9U encrypted privilege 0
username kuzma attributes
 vpn-group-policy ATSAdmin
username nate password BXHOURyT37e4O5mt encrypted privilege 0
username nate attributes
 vpn-group-policy ATSAdmin
tunnel-group ATSAdmin type remote-access
tunnel-group ATSAdmin general-attributes
 address-pool VPNIPs
 default-group-policy ATSAdmin
tunnel-group SSLVPN type remote-access
tunnel-group SSLVPN general-attributes
 address-pool VPNIPs
 default-group-policy ATSAdmin
!
class-map inspection_default
 match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
 parameters
  message-length maximum 512
policy-map global_policy
 class inspection_default
  inspect dns preset_dns_map 
  inspect ftp 
  inspect h323 h225 
  inspect h323 ras 
  inspect rsh 
  inspect rtsp 
  inspect esmtp 
  inspect sqlnet 
  inspect skinny  
  inspect sunrpc 
  inspect xdmcp 
  inspect sip  
  inspect netbios 
  inspect tftp 
  inspect ip-options 
!
service-policy global_policy global
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command uauth
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context 
call-home
 profile CiscoTAC-1
  no active
  destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
  destination address email callhome@cisco.com
  destination transport-method http
  subscribe-to-alert-group diagnostic
  subscribe-to-alert-group environment
  subscribe-to-alert-group inventory periodic monthly
  subscribe-to-alert-group configuration periodic monthly
  subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:0ed0580e151af288d865f4f3603d792a
: end
asdm image disk0:/asdm-635.bin
no asdm history enable
share|improve this question
1  
Hi - probably not a good idea to post your entire config file here, including usernames and passwords in clear text! If you must post the full config, at least format it so it is readable. –  dunxd Mar 16 '11 at 15:18
1  
Agree; if you'd be so kind as to clean up your configuration I'd be happy to take a look. Its too hard to follow right now. Also when you clean up the config - show us what it looks like when things are working (i.e. you are able to browse out) and then what it looks like when its broken (can't browse out nor inbound). –  Jason Seemann Mar 16 '11 at 15:27

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Browse other questions tagged or ask your own question.