Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

Installing Windows from a thumb drive is vastly superior to burning a copy to a DVD which will fill some landfill somewhere with toxic stuff. Not to mention it's about 50x faster to install Windows from a USB Thumb Drive.

How do you get the bits onto the thumb drive so that you can boot from it and do a clean install?

share|improve this question
    
Thanks Omar, I found your question after typing in the title to my own question. Was looking for Windows 2008, but they'll all be the same. –  p.campbell May 2 '09 at 5:36

6 Answers 6

Try Rufus

Rufus is an utility that helps format and create bootable USB flash drives, such as USB keys/pendrives, memory sticks, etc.

It can be especially useful for cases where:

  • you need to create USB installation media from bootable ISOs (Windows, Linux, UEFI, etc.)
  • you need to work on a system that doesn't have an OS installed
  • you need to flash a BIOS or other firmware from DOS
  • you want to run a low-level utility

Despite its small size, Rufus provides everything you need!

share|improve this answer
up vote 76 down vote accepted

Update: Microsoft has created the Windows 7 USB/DVD Download tool to make this very easy.

I used this guide as a set of directions - http://kurtsh.spaces.live.com/blog/cns!DA410C7F7E038D!1665.entry

The steps are really longer than necessary. You need to:

1. Get a fast 4GB or larger USB Thumbdrive.

2. Run cmd.exe and enter the following commands followed by Enter

  1. diskpart
  2. list disk
  3. select disk 1 (select your usb disk which number you have determined in step 2)
  4. clean
  5. create partition primary
  6. select partition 1
  7. active
  8. format fs=ntfs quick
  9. assign
  10. exit
  11. bootsect.exe /nt60 F: (where F: is the drive letter of your USB drive as reported by the assign diskpart command in step 9.)

3. Copy the Windows sources from the CD or other source using robocopy

robocopy.exe E:\ F:\ /MIR

where E:\ is the source and F:\ is the destination (thumbdrive)

Configure your PC to boot from the USB drive

This is the tricky part. For most of the machines I've tried the USB thumbdrive will appear to the BIOS as any other hard drive. You need to muck with the boot sequence to place the thumbdrive higher in the boot order than the local hard drive.

Note that after you do this you might want to reset the boot order in order to ensure that BitLocker doesn't detect boot changes based on the fact that the thumdrive is missing if it was there when you encrypted your drive.

share|improve this answer
    
+1 for making abootable thumb drive w/diskpart. Nice touch. –  WaldenL May 2 '09 at 4:36
    
+1 for reminding me about robocopy –  David Heggie May 7 '09 at 15:34
2  
'format fs=ntfs quick' to quick format which takes significantly less time than a full format –  basszero May 13 '09 at 21:34
2  
If I'm not mistaking Step 2.2 "select disk 1" is not always disk 1. –  Boris Callens Sep 6 '10 at 18:08
1  
@mmdemirbas I also would think so especially since the 10 steps are missing any procedure to actually equip the drive with a boot loader so far, so the resulting USB drive would not boot. And the USB/DVD download tool only would work for Windows 7. –  the-wabbit Dec 12 '12 at 23:56

Use MultiSystem if you're creating the USB drive from linux.

http://www.pendrivelinux.com/multiboot-create-a-multiboot-usb-from-linux/

share|improve this answer
    
Whilst this may theoretically answer the question, it would be preferable to include the essential parts of the answer here, and provide the link for reference. –  Scott Pack Nov 21 '12 at 0:30

There is a tool (YUMI) to achieve this. I think, it is fastest and painless way of preparing a (multi)bootable usb. You can put many systems (Windows, Linux, HBCD etc.) into one flash drive. And you can also use an external drive.

share|improve this answer

Quick tip I hope will help people going through the same pain as me when trying to create a thumb drive for Windows Server 2008

I had an old USB led around, but it wouldn't mount for me to run diskpart on it.

Turns out it was formatted in FAT16. Mount it on a laptop with a proper OS, reformat it to FAT32, then plug it back into the Windows Server 2008 box and it mounts. Then run diskpart as above.

share|improve this answer

I found two problems with the accepted answer:

  1. It assumes the usb drive is disk 1 for DISKPART.
    This can be resolved by using the LIST DISK command prior to SELECT DISK # to determine the correct disk number.

  2. The usb drive did not appear as a bootable device to the target machine.
    This can be fixed by running the bootsect utility off the Windows installation DVD.

    Before copying the contents of the Windows DVD:

    1. Run cmd.exe as Administrator
    2. Select your optical drive (assumed to be D:)
    3. Type CD boot
    4. Type D:\boot\bootsect.exe /nt60 U: (where U: is your USB drive)

Adding these extra steps I was able to install Windows 7 from a USB HDD onto a Samsung NC10 Netbook.

If this proves unsuccessful some other techniques (including the accepted answer with the above steps) can be found at http://www.bootdisk.com/pendrive.htm.

share|improve this answer

protected by Chris S Jun 15 at 20:54

Thank you for your interest in this question. Because it has attracted low-quality answers, posting an answer now requires 10 reputation on this site.

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged or ask your own question.