Sign up ×
Server Fault is a question and answer site for system and network administrators. It's 100% free, no registration required.

I am using slapadd to restore a backup. That backup contains 45k entries which takes a while to restore so I need to get some progress update from slapadd. Luckily for me there is the -v switch which gives an output similar to this one:

added: ",ou=People,dc=example,dc=org" (00003d53)
added: ",ou=People,dc=example,dc=org" (00003d54)
added: ",ou=People,dc=example,dc=org" (00003d55)
.########              44.22% eta 05m05s elapsed             04m spd  29.2 k/s 
added: ",ou=People,dc=example,dc=org" (00003d56)
added: ",ou=People,dc=example,dc=org" (00003d57)
added: ",ou=People,dc=example,dc=org" (00003d58)
added: ",ou=People,dc=example,dc=org" (00003d59)

Every N entries added, slapadd writes a progress update output line (.######## 44.22% eta 05m05s elapsed ...) which I want to keep and an output line for every entry created which I want to hide because it exposes people's email address but still want to count them to know how many users were imported

The way I thought about hiding emails and showing the progress update is this:

$ slapadd -v ... 2>&1 | tee log.txt | grep '########'
# => would give me real-time progress update
$ grep "added" log.txt | wc -l
# => once backup has been restored I would know how many users were added

I tried different variations of the above, and whatever I try I can't grep the progress update output line.

I traced slapadd as follows:

sudo strace slapadd -v ...

And here is what I get:

write(2, "added: \""..., 78added: ",ou=People,dc=example,dc=org" (00000009)
) = 78
gettimeofday({1322645227, 253338}, NULL) = 0
_########    44.22% eta 05m05s elapsed      04m spd  29.2 k/s    ) = 80
write(2, "\n", 1

As you can see, the percentage line isn't sent to either stdout or stderr (FYI I have validated with known working and failing commands that 2 is stderr and 1 is stdout)

Q1: Where is the progress update output line going?
Q2: How can I grep on it while sending stderr to a file?

Additional info: I'm running Openldap 2.4.21 on ubuntu server 10.04

1st update: potentially relevant info


("meter" being what I called above the "progress update output line")

> No, the code only enables the meter if stdout (was: stderr) is a tty, so
> redirecting it anywhere disables it.  The meter was enabled both by
> "slapadd -l file" and "slapadd<  file", but "cat file | slapadd" did
> disable it.  IMHO not exactly an obvious way..

Still my questions remain as I don't know what to do with that additional info.

share|improve this question
strace again and look which file/device belongs to filehandle 2. – mailq Nov 30 '11 at 10:09
Don't know how to do it so it will take me a bit of time to find out. In the meantime can you look at the update I put in my question to see if you can advise further from there? Thanks. – user64204 Nov 30 '11 at 10:17

1 Answer 1

up vote 2 down vote accepted

You've been bitten by a funny behaviour of slapadd. There was a discussion on the developer's mailing list about it. Bottom line is that the pogress meter seems to get disabled when redirecting stderr or is only enabled when STDIN is a tty (I wasn't able to reach a definitive conclusion based on a few google searches - seems you need to dive into the code!).

Other than that, you're on the right track. For Q2; I'm not so sure about your question here, but to redirect STDERR to a file, just do slapadd -v ... 2>YOURFILE. This way you can still grep on STDOUT (1).

share|improve this answer
I can indeed redirect stderr to a file in which case I get the added: "mail=... lines and I can count the number of users imported. However I loose the meter line :( Honestly why would you output the meter line to something different than stderr or stdout, what's the point of doing this? – user64204 Nov 30 '11 at 10:27
Because it is useless for other programs in the pipe. But I see that you have a use case for that. I haven't tried if you could grab the data from /dev/console or /dev/ttyX while you not redirect the output? – mailq Nov 30 '11 at 11:37
I see your point, but in my opinion it would be better to have the meter sent to stdout and the emails to stderr to facilitate the parsing of these 2 outputs. Anyway, could you give me directions as to how reading data from dev/console or /dev/ttyX please? – user64204 Nov 30 '11 at 13:23

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.