I believe I've achieved a table that routes packets from and to eth1/192.168.3.x through 192.168.3.1, and packets from and to eth0/192.168.1.x through 192.168.1.1 (helpful source).
Question: when doing tracepath from 192.168.3.20 (from within vserver), I'm getting
kernel: [318535.927489] martian source 192.168.3.20 from 18.104.22.168, on dev eth0 at or near the target IP, while intermediary hops go without (log below).
I don't understand why this packet is arriving on eth0, instead of eth1, even after reading this:
Note that you may see packets from non-routable IP addresses when running the traceroute or tracepath commands. While packets cannot be routed to these routers, packets sent between 2 routers only need to know the address of the next hop within the local networks, which could be a non-routable address.
Can someone explain that paragraph in human language? Based on short initial trials so far, everything else seems to work without causing martians. Is this contained to the nature of tracepath operation or do I have some other bigger routing problem that will cause work traffic breakage?
Side note: is it possible to inspect martian packet with tcpdump or wireshark or anything of the sort? I'm have not been able to get it to show up on my own.
vserver-20 / # tracepath -n 22.214.171.124 1: 192.168.3.2 0.064ms pmtu 1500 1: 192.168.3.1 1.076ms 1: 192.168.3.1 1.259ms 2: 126.96.36.199 1.908ms 3: 188.8.131.52 2.595ms 4: 184.108.40.206 2.136ms asymm 5 5: 220.127.116.11 2.266ms asymm 6 6: 18.104.22.168 2.390ms asymm 7 7: no reply 8: no reply 9: no reply ^C
$ sudo ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:24:1d:de:b3:5d brd ff:ff:ff:ff:ff:ff inet 192.168.1.2/24 scope global eth0 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:46:46:a3:6a brd ff:ff:ff:ff:ff:ff inet 192.168.3.2/27 scope global eth1 inet 192.168.3.20/27 brd 192.168.3.31 scope global secondary eth1 # linux-vserver instance $ sudo ip route default via 192.168.1.1 dev eth0 metric 3 unreachable 127.0.0.0/8 scope host 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2 192.168.3.0/27 dev eth1 proto kernel scope link src 192.168.3.2 $ sudo ip rule 0: from all lookup local 32764: from all to 192.168.3.0/27 lookup dmz 32765: from 192.168.3.0/27 lookup dmz 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table dmz default via 192.168.3.1 dev eth1 metric 4 192.168.3.0/27 dev eth1 scope link metric 4
# ip route 10.24.0.2 dev tun0 proto kernel scope link src 10.24.0.1 10.24.0.0/24 via 10.24.0.2 dev tun0 192.168.3.0/24 dev br-dmz proto kernel scope link src 192.168.3.1 192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1 $ISP_NET/23 dev eth0.1 proto kernel scope link src $WAN_IP default via $ISP_GW dev eth0.1