Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

I am looking at replacing our aging router - an old Cisco 2811 - with a new unit. What kind of criteria should I be looking at to select a model?

I have a few fairly long runs I'm looking at so I'm going to need fiber interfaces. I also have about a dozen local switches, each of which should have a 1 gig uplink.

The switches we use for our servers (HP 2900 series) support a 10 GB back pane which I'd like to leverage for my router access.

Ideally I'd like the 10 gig ports for linking to my servers to run at wire speed.

share|improve this question
    
What is your router connecting together? –  resmon6 May 15 '12 at 17:01
    
@resmon6 - about a dozen switches 1 gigabit copper, two server switches 10 gigabit plus a couple fiber connections. –  Tim Brigham May 15 '12 at 17:18
4  
Moderator's note: Tim took great care to avoid this being a "recommend me a product" post, and instead phrased it as "What features should I be interested in". So I'm going to hammer comments recommending specific models without any support to them. –  sysadmin1138 May 15 '12 at 18:47

2 Answers 2

up vote 4 down vote accepted

One thing to be aware of with the HP 2900 series 10GbE backplane, it reportedly acts like a 10-pack of trunked 1GbE lines. This is just fine when working as an inter-switch link, but is less useful when attached to something like a large filer node.

Based on what you're looking for, I'd look for the following features in a new switch/router:

  • Modular. You have needs for both copper and fiber connections, as well as 10GbE needs. A modular switch will help you get what you need without having look for an all-in-one.
  • Backplane speeds. Enough backplane to support your traffic. With the 10GbE this can become an issue, especially in a modular switch that might have different bandwidth between modules as within them.
  • IPv6 support. Anything new should have it, but L3 switches may not have all the features needed for a true v6 router. The HP 2900-series don't.
  • Trunking support with your existing switches. Kind of a gimmie, but sometimes... support is spotty. The big-names should all work together.
share|improve this answer
1  
sysadmin, I am very interested in a source for the claim of hp 2900 that "acts like a 10-pack of trunked 1GbE lines", as I am considering the hp's (a long with some dell switches). Tried googling but couldn't find anything. –  3molo May 15 '12 at 19:14
    
I'm pretty sure I found it on the old HP ITRC forums, but am having trouble digging it out of the back-country of the Internet. Those ports are intended to be uplinks not host-ports. If I remember the article right, the person was complaining of not getting more than 125MB/s flow through that port for a single conversation and the reply was that it was working as designed. On a switch w/ GbE ports, you'd expect the max-flow to be 1 GbE wide. –  sysadmin1138 May 15 '12 at 19:57

I recommend that you look into Vyatta it markets itself as a direct competitor to Cisco. The command line is similar and the features rich. Vyatta make a number of appliances and they also sell the software to install and run on your own hardware. (there is also an open source edition) I am running the open source version of Vyatta in a few locations. For my largest install I have a Vyatta in-front of my DMZ servers as a bridge providing firewalling and ThreatStop and another one routing between 3 networks. I have it connected to a stack of Dell Powerconnect 6248 switches. It also provides a VPN into 2 data centres. Another setup I have in the Amazon cloud and another setup is providing VLANS and failover for a large serviced office (with QOS).

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.