Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

Cage nuts can be inserted (in square holes) either with the flaps horizontal or vertical. I've seen and used both methods, but am still not sure which is best. Is there a recommended way of inserting them? If so, why is it the best way?

enter image description here

From my own experience, the horizontal way (on the left) seems slightly better for no other reason than making it easier to insert or pry out the cage nut in a full rack (with the units above and below being populated), for example when replacing cage nuts with a snap-in rail.

Edit: Major vendors each seem to have their own preference too:

Horizontal: IBM, Cisco, APC

Vertical: HP (and Compaq), Sun/Oracle, Dell

share|improve this question

6 Answers 6

up vote 8 down vote accepted

I've always done them horizontally, because that way you always have clear access to the tang with a screwdriver. If you install them vertically there is potential for good access to the tang to be obscured by equipment above or below, or the top or bottom of the rack.

share|improve this answer

I prefer the vertical mounting on the right of your illustration. To remove them I put my thumb on top and my index finger below. I have all of my fingers except for my thumb curled back onto my hand like I'm gripping something. Push down and the nut rolls right out. If it falls it's only going to fall into my palm. I just squeeze to close my fingers and I have it.

I've found that when they are mounted horizontally that sometimes my fingers won't catch them and they go flying, never to be found again (at least until you empty or remove the whole rack). Using a screwdriver makes the "go flying" part even worse.

share|improve this answer
6  
Buy a cagenut tool, and life will be easy. –  Zoredache Jun 29 '12 at 17:16
    
That's a good tip. A cage nut tool would most definitely be useful if you add and remove a lot of cage nuts. We don't add or remove many where I work thanks to blades and virtualization, so we do it by hand rather than keep track of another single-purpose tool. –  Starfish Jun 29 '12 at 17:24
1  
+1, same thing I do and same reasons. If I kept a special tool around for every task I did a few times a year, I'd be drowning in tools, and never be able to find the one I need when I need it. –  HopelessN00b Jun 29 '12 at 17:53

I've always been told to do it horizontally. This document from APC would also seem to indicate that, though it doesn't say why.

share|improve this answer

I suspect it is far better to place them horizontally, so the flaps are in the direction of the force of gravity.

I suspect if you think of it like corrugated cardboard, the flap kinda looks like a single corrugation, then you might see what I am trying to say.. When push on the cardboard from the side it is far more likely to collapse, but if you push on it from the top, it is extremely sturdy.

If the metal uses was extremely weak, or the gravitational forces (weight) acting on it was very strong, it seems to me that the lower flap of the vertical orientation, might bend inward a bit resulting in a cagenut that falls out of the slot. Whereas the

I suppose if your rack had any reason for some side-to-side force acting on it, you might want do it the other way.

share|improve this answer
    
the wings don't support anything. it just keeps the nut lined up with the hole while you insert the screw. all of the weight is carried by the screw resting on the bottom of the square hole, combined with the compression of the screw pulling the nut against the rack and against the device mounting bracket. –  longneck Jun 29 '12 at 17:46
    
@longneck, I seen equipment mounted where that is not the case. I have seen skinny screw that do not appear to rest on the edge of the bottom of the hole. OTOH, yeah if the cage fails in that case, it is just going to do so in a way that results in the screw resting on the bottom of the hole. It really shouldn't be a big deal. –  Zoredache Jun 29 '12 at 17:59

I've found that it's better to mount Cage Nuts vertically.

I had a weird case where (during installation) the weight of the device pulled the top flap of the cage nut down, which caused the cage nut to come loose.

This was mainly due to the fact that the only screws installed were the bottom row (half-way screwed in), with the weight of the device on them.. again, it's a weird situation..

anyway, I had to pull the device out to remount the Cage Nut, so out of curiosity I mounted the Cage Nut vertically and recreated the scenario.. and didn't have the same issue..

so anyway, i vote for vertical..

share|improve this answer
1  
The only way that can happen is if the screws into the nuts weren't properly tightened. –  John Gardeniers Jan 16 '13 at 7:53

The problem with horizontal is that things mounted that way tend to settle slightly into the height unit below if it is empty, fouling it - if whatever is at another unit lower has been mounted perfectly, getting something in there will need a mallet...

share|improve this answer
    
Good point, although I've found that happens no matter which way the nuts are mounted. –  Ingmar Hupp Jan 16 '13 at 14:26
    
Very dependent on the exact rails and nuts... there are some brands that just dont go together well.... whether horizontal or vertical, it is sometimes good for your sanity to identify the types that are good and those which are not good with your currently used racks... then sort the storage box and throw any types that aren't good away. –  rackandboneman Jan 17 '13 at 10:35

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.