Since a few days, I'm trying to configure my KVM vm to have a public IP address, without any success.
First, I'm on OVH, and you need to know they don't allow networking from different mac addresses. I have so registered a virtual mac address associated with my failover IP
Here's my configuration:
Guest wanted IP: 46.105.40.x
Host IP: 176.31.240.x
dummy0 interface: ifcfg-dummy0
BOOTPROTO=static IPADDR=10.0.0.1 NETMASK=255.0.0.0 ONBOOT=yes NM_CONTROLLED=no ARP=yes BRIDGE=br0
br0 bridge: ifcfg-br0
DEVICE=br0 TYPE=Bridge DELAY=0 ONBOOT=yes BOOTPROTO=static IPADDR=192.168.1.1 NETMASK=255.255.255.0 PEERDNS=yes NM_CONTROLLED=no ARP=yes
Failover ip is redirected to the br0 bridge with
ip route add 46.105.40.xxx dev br0
> cat /proc/sys/net/ipv4/ip_forward 1 > cat /proc/sys/net/ipv4/conf/vnet0/proxy_arp 1 > route -n Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 126.96.36.199 0.0.0.0 UG 0 0 0 eth0 46.105.40.x 0.0.0.0 255.255.255.255 UH 0 0 0 br0 188.8.131.52 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0
<interface type='bridge'> <mac address='02:00:00:30:22:05'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </interface>
I've borrowed most of the OVH configuration here (in french, http://guides.ovh.com/BridgeClient) for the guest configuration
eth0 interface: ifcfg-eth0
DEVICE="eth0" BOOTPROTO=none HWADDR="02:00:00:30:22:05" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" UUID="e9138469-0d81-4ee6-b5ab-de0d7d17d1c8" USERCTL=no PEERDNS=yes IPADDR=46.105.40.xxx NETMASK=255.255.255.255 GATEWAY=184.108.40.206 ARP=yes
For the routes, I have in route-eth0:
220.127.116.11 dev eth0 default via 18.104.22.168 dev eth0
With this configuration, I don't have any access to the internet. The only thing I can do is to ping the public ip of the host, nothing more. My final conclusion is that the route does not work, because, when, on the guest, I run
ping 22.214.171.124, I have, on the host:
> tcpdump -i vnet0 icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on br0, link-type EN10MB (Ethernet), capture size 65535 bytes 13:38:09.009324 IP 46-105-40-xxx.kimsufi.com > google-public-dns-a.google.com: ICMP echo request, id 50183, seq 1, length 64 13:38:09.815344 IP 46-105-40-xxx.kimsufi.com > google-public-dns-a.google.com: ICMP echo request, id 50183, seq 2, length 64
I never get the ping reply, only the request. It seems Guest -> Host communication is fine.
> tcpdump -i eth0 icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 13:39:40.240561 IP 46-105-40-xxx.kimsufi.com > google-public-dns-a.google.com: ICMP echo request, id 50439, seq 1, length 64 13:39:40.250161 IP google-public-dns-a.google.com > 46-105-40-xxx.kimsufi.com: ICMP echo reply, id 50439, seq 1, length 64
I have the request and the reply on eth0, but reply is not forwarded to the bridge. I really don't understand why, I though it was the aim of the route to do that!
IPtables is disabled on both host and guest.
I really hope some of you will be able to help me!
Many thanks in advance,