Take the 2-minute tour ×
Server Fault is a question and answer site for professional system and network administrators. It's 100% free, no registration required.

I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious.

There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection.

I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN.

The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B.

How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa.

Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up?

Diagram of the network: (Hopefully this kind of helps)

       WAN1                                    WAN2
        |                                       |
[ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ]
        |                                       |  
       (X2)                               192.168.2.0/24
    10.1.1.0/24

Any help would be greatly appriciated!

share|improve this question
1  
Is router 2 just a router, or is it also a stateful firewall? –  SpacemanSpiff Nov 24 '12 at 21:08
    
Router 2 is a stateful firewall, although this shouldn't matter. If I SSH into the SonicWall, I can ping devices on Network B. The X3 port on the SonicWall is actually plugged into a switch that Router 2 is also connected to. –  Rain Nov 24 '12 at 21:28
    
Sure, that's because the Sonicwall has an interface directly in the 2.0/24 network that you can get a direct ARP response from. I'm trying to figure out how to use a dedicated subnet on the Sonicwall just for GlobalVPN clients... you will need to add a static route onto RT2 for that subnet, I just don't see how to create it just yet. I think a new zone, with a loopback interface in that zone would do it. –  SpacemanSpiff Nov 24 '12 at 21:30
    
I wish I could full prove this out for you,but I'm fairly certain the answer to your problem will be under the "DHCP over VPN" configuration section under VPN –  SpacemanSpiff Nov 24 '12 at 21:45
    
I've tried every permutation of settings in the "DHCP over VPN" section. I find it interesting that there is a VPN zone pre-configured but it simply shares the LAN Subnet (on X1, in this case). Network A is currently accessible, although Network B and even the X3 Interface IP are not. –  Rain Nov 24 '12 at 22:40

1 Answer 1

up vote 0 down vote accepted

The problem was not that VPN clients could not access the X3 network, any LAN device on the Sonicwall could not access the X3 network. Once a NAT entry was created to properally translate the source/destination of the packets destined for the X3 network everything worked fine. This is also described in a bit more detail in this question: Sonicwall routing between multiple subnets on multiple interfaces

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.