I have a weird thing happening on our network at my office which I can't quite get my head around. In particular I can't tell if it's a problem with a switch, or a problem with configuration.
We have a Cisco SG300-52 switch (sw01) in the top of a rack in our server room, connected to another SG300-28 that acts as our core switch (core01). Both run layer 2 only, our firewalls do routing between VLANs. They have a dozen or so VLANs between them. Gi1 on sw01 is a trunk port connected to gi1 on core01.
(Disclosure: There are other switches in our environment but I'm pretty sure I've isolated the problem down to these two. Happy to provide more info if necessary.)
The behaviour I'm seeing is limited to one VLAN, vlan 12 -- or, at least, it's not happening on the other ones I checked (It's hard to guarantee the absence of packets), and it is: sw01 is forwarding, to core01, traffic which is between two hosts which are both plugged into sw01. (I noticed this because the IDS in our firewall gave a false positive on traffic which should not reach the firewall.)
We noticed this mostly between our two dhcp/dns servers, net01 (10.12.0.10) and net02 (10.12.0.11). net01 is physical hardware and net02 is on a VMware ESX server. net01 is connected to gi44 on sw01 and net02's ESX server to gi11.
Let's see some interfaces! Remember, vlan 12 is the problem vlan. Of the others I explicitly verified that vlan 27 was not affected.
Here's the two hosts' ports: esx01 contains net02.
sw01#sh run int gi11 interface gigabitethernet11 description esx01 lldp med disable switchport trunk allowed vlan add 5-7,11-13,100 switchport trunk native vlan 27 ! sw01#sh run int gi44 interface gigabitethernet44 description net01-1 lldp med disable switchport mode access switchport access vlan 12 !
Here's the trunk on sw01.
sw01#sh run int gi1 interface gigabitethernet1 description "trunk to core01" lldp med disable switchport trunk allowed vlan add 4-7,11-13,27,100 !
And the other end of the trunk on core01.
interface gigabitethernet1 description sw01 macro description switch switchport trunk allowed vlan add 2-7,11-16,27,100 !
I have a monitor port on core01, thus:
core01#sh run int gi12 interface gigabitethernet12 description "monitor port" port monitor GigabitEthernet 1 !
And the monitor port on core01 sees unicast traffic going between net01 and net02, both of which are on sw01! I've verified this with a monitor port on sw01 that sees the net01-net02 unicast traffic leaving via gi1 too.
sw01 knows that both of those hosts are on ports that are not its trunk port:
:) ratchet$ arp -a | grep net net02.2ndsiteinc.com (10.12.0.11) at 00:0C:29:1A:66:15 [ether] on eth0 net01.2ndsiteinc.com (10.12.0.10) at 00:11:43:D8:9F:94 [ether] on eth0 sw01#sh mac addr addr 00:0C:29:1A:66:15 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:0c:29:1a:66:15 gi11 dynamic sw01#sh mac addr addr 00:11:43:D8:9F:94 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:11:43:d8:9f:94 gi44 dynamic
I also brought up an unused port on sw01 on vlan 12, but the unicast traffic was (as best as I could tell) not coming out that port. So it doesn't look like sw01 is pushing it out all its ports, just the right ports and also gi1!
I've verified that sw01 is not filling up its address-table:
sw01#sh mac addr count This may take some time. Capacity : 8192 Free : 7983 Used : 208
sw01#sh ver SW version 184.108.40.206 ( date 12-Nov-2011 time 23:34:26 ) Boot version 220.127.116.11 ( date 08-Apr-2010 time 16:37:57 ) HW version V01 core01#sh ver SW version 18.104.22.168 ( date 12-Nov-2011 time 23:34:26 ) Boot version 22.214.171.124 ( date 11-May-2011 time 18:31:00 ) HW version V01
So my understanding is this: sw01 should take unicast traffic for net01 and send it only out net02's port, and vice versa; none of it should go out sw01's uplink. But core01, receiving traffic on gi1 for a host it knows is on gi1, is right in sending it out all of its ports. (That is: sw01 is misbehaving, but core01 is doing what it should given the circumstances.)
My question is: Why is sw01 sending that unicast traffic out its uplink, gi1?
(And pre-emptively: yes, I know SG300s leave much to be desired, and yes, we should have spanning-tree enabled, but that's where I'm at right now.)