1

I've installed Red Hat's cluster software on an install of CentOS 6.5, and use it to provide redundant routing from one network to another. This works fine, and I have a pair of boxes providing the service, so that if one fails (for example, if I test by removing its network connections), the other takes over routing.

However, if I then have to do anything to the remaining box, I can't restart it due to problems with rgmanager:

service rgmanager stop

hangs, and the only way to stop the process is to kill -9 it. This obviously also affects any action that tries to stop the service, like a reboot or poweroff.

When I do manage to start the server on its own, although the cluster starts, rgmanager is not shown as running in clustat and none of the redundant routing services are even visible, let alone start.

This could cause problems if, for instance, the boxes are deployed to a remote location, and need to be powered down before we've had a chance to replace the failed box.

Here's my cluster.conf:

<?xml version="1.0"?>
<cluster config_version="2" name="router-ha">
        <fence_daemon/>
        <clusternodes>
                <clusternode name="router-01" nodeid="1"/>
                <clusternode name="router-02" nodeid="2"/>
        </clusternodes>
        <cman expected_votes="1" two_node="1"/>
        <fencedevices/>
        <rm>
                <failoverdomains/>
                <resources>
                        <ip address="10.0.0.1" monitor_link="1" sleeptime="0"/>
                        <ip address="10.0.0.2" monitor_link="1" sleeptime="0"/>
                        <ip address="10.2.0.1" monitor_link="1" sleeptime="0"/>
                        <ip address="10.4.0.1" monitor_link="1" sleeptime="0"/>
                </resources>
                <service autostart="1" name="routing-a" recovery="restart">
                        <ip ref="10.0.0.1"/>
                        <ip ref="10.2.0.1"/>
                </service>
                <service autostart="1" name="routing-b" recovery="restart">
                        <ip ref="10.0.0.2"/>
                        <ip ref="10.4.0.1"/>
                </service>
        </rm>
</cluster>

Why can't I start the service on a single box if it can't see the other? Surely it's a required part of being a redundant pair that you don't depend on the other machine to be able to start a cluster service?

1 Answer 1

0

To run clustered services, a quorum is needed. Typically in for example a three-node cluster, every member has one vote each: If you pull the plug on one, it will know that it is inquorate as it has less than half of the available votes (the value is actually configurable). A cluster without quorum is not fit to run clustered services on.

This principle is not just for Red Hat clusters, but a general principle. The solutions and implementations may vary though. Also the implementations of two-node clusters, since if you give both nodes one vote each, not a single one of them would normally be quorate.

Surely it's a required part of being a redundant pair that you don't depend on the other machine to be able to start a cluster service?

In the case of Red Hat, in a two-node cluster, a special condition apply:

    <cman expected_votes="1" two_node="1"/>

What will happen when you pull the plug is that both nodes will lose contact with each other.

To determine which one of them has quorum, they will both try to STONITH each other.

STONITH is an acronym for Shoot-The-Other-Node-In-The-Head and it protects your data from being corrupted by rogue nodes or concurrent access. Just because a node is unresponsive, this does not mean it is not accessing your data. The only way to be 100% sure that your data is safe, is to fence the node using STONITH so we can be certain that the node is truly offline, before allowing the data to be accessed from another node.

So the assumption you make is correct, your cluster is misconfigured and requires a fencing agent to be operational, because by pulling the plug, not only do you make your service unavailable, which would normally cause rgmanager to fail-over to other node (or how ever you've configured it to do), you also remove the heartbeat-link between the clustered nodes. Even though rgmanager may try to do what you've configured it to do, cman still cannot figure out which one of these nodes has quorum. Instead it will consistently try to fence the other node, but since you've no fence-agent configured, it will be stuck indefinitly.

So here are two good advice to you:

  1. separate the cluster traffic from the network traffic by adding an additional interface to your cluster nodes, on an isolated net, so that when you pull the plug on the application-facing interface, the cluster will do a clean fail-over
  2. Configure fencing.

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .