Address Resolution Protocol is a layer 2 networking protocol used for resolving layer 3 addresses (such as IP addresses) into layer 2 addresses (such as Ethernet MACs). It is used by network devices when communicating with devices on the same layer 2 network.

learn more… | top users | synonyms

0
votes
3answers
96 views

Linux (Ubuntu 12.04) sending ARP requests over single interface

I have a system with custom hardware hooked up to 2 different ethernet ports on the same system. The interfaces are configured on the same subnet because the hardware (FPGA-based) has a hardcoded IP ...
1
vote
2answers
374 views

Is there a way to trace what's sending gratuitous arps?

We have a box that's just started acting up and we're not really sure why. It has IP address (dummy examples) 199.199.199.1 on eth0, 127.0.0.2 on eth1, and 199.199.199.2 on eth1:0. Recently, for some ...
3
votes
1answer
315 views

Windows Server 2008 ARP Cache Poisioning

Recently ran into a very strange problem. Several applications were having issues communication through our F5 Load-Balancer. When we looked into it we found that the router had an incorrect ARP and ...
3
votes
1answer
941 views

ARP reply vanishes from br0 to tap0 using OpenVPN in bridging mode

i have setup a linux box (on an esxi5) which acts as an openvpn server. the server is configured to use bridging for the clients, which essentially works, with one exception. if the client pings some ...
2
votes
1answer
156 views

nmap and arp-scan inconsistent IP-MAC results

I seem to get variable and inconsistent results for the IP/MAC addresses from a particular machine, using nmap or arp-scan. The machine has 3 interfaces, and this is what it shows: $ uname -a Linux ...
2
votes
1answer
983 views

Linux machine does not answer an ARP request

We have this situation: A router, which is an Ubuntu VM, has multiple VLAN interfaces on the same physical NIC. Those VLAN interfaces are dynamically configured and torn down and attached to networks ...
1
vote
1answer
139 views

arp problems with transparent bridge on linux

I've been trying to secure my virtual machines on my esx server by putting them behind a transparent bridge with 2 interfaces, one in front, one at the back. My intention is to put all the firewall ...
1
vote
1answer
50 views

Understanding ARP traces during OS load

Consider the following ARP packets captured while a unix machine was booting. From the packets I understand that this machine whose MAC address is 00:22:22:22:22:22 is requesting information about ...
1
vote
1answer
626 views

ARP response is not present on the other port of linux bridge based on ubuntu 13.10

I recently build linux based bridge for packet monitoring purpose, but there is BIG problem. the environment is, overall env. target of monitoring is VMs on vSphere. two vSwitches are configured ...
1
vote
1answer
208 views

openvpn connects but does not work until server pings client

I'm trying to configure a connection using openvpn from a windows 7 client machine to a linux host. I'm using openvpn in the traditional routed mode using tap devices, and the configuration I'm using ...
1
vote
1answer
189 views

Proxy arp and 1:1 NAT

I have a Linux router with 2 NICs doing masquerade from network 192.168.0.0/24 to an ADSL router. users <----> NIC A [router] NIC B <----> INTERNET Now I'm experimenting with proxy arp ...
1
vote
1answer
1k views

How to setup a static multicast ARP entry with Cisco SG300?

We're running a Microsoft NLB cluster in multicast mode as a loadbalancer. Using our old Cisco IOS switches we propagate access to the cluster to our branches using a static ARP entry in the core ...
0
votes
1answer
375 views

Solaris Slow ARP Failure Unreachable Host

We have been experiencing slow timeouts for unreachable hosts is extremely slow. Recent testing in our lab shows it may be a delay reporting negative ARP lookups. Dumping traffic during attempts to ...
0
votes
1answer
204 views

Adding entries for incoming arp requests to ARP cache?

Given a host A und B within the same broadcast domain whose ARP caches are both empty, under what circumstances would B add an entry for A to its ARP cache when replying to an incoming ARP request ...
0
votes
1answer
497 views

Direct server return, ARP problem

I'm trying to implement Direct Server Return scheme for our web cluster and I think i got stuck with some ARP issues. For testing purposes I deployed 2 virtual servers (inside ESXi environment). Host ...
0
votes
1answer
357 views

ARP request are sent even though windows has an entry in cache (ARP Table)

we have a product which runs on windows XP embedded SP1. We add a fake(does not exists) MAC address for a fake IP in ARP table. When there is a communication happening Windows sends packets to the ...
3
votes
0answers
90 views

VMXNET3 nic loses the ability to update ARP table after N hours

I have a fedora 18 VM that stops updating the arp table on eth1 after running for a number of hours to days. There are other VMs on the same hypervisor that can access all of the same networks without ...
3
votes
0answers
409 views

Dynamic ARP Entries turning into Static ARP entries

I recently acquired a client that has a strange ARP caching issue on one of thier servers. I have a server that will eventually start turning it's dynamic ARP entries into static ARP entries. This ...
2
votes
0answers
130 views

Keepalived failover not working for Static NAT target behind Cisco ASA

I've got a Cisco ASA[0] with a pair of Linux boxes in the DMZ running Keepalived and HAproxy acting as a load-balancing failover pair for another pair of Windows servers, also in the DMZ. I'm ...
2
votes
0answers
94 views

I am not able to connect to my server from my leased line internet connection

I am having some troubles connecting to my Fedora server from my static IP ISP connection. Usually I can ping that server with no problems. But other times it just gives me timeout responses. When ...
2
votes
0answers
115 views

Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me ...
2
votes
0answers
55 views

Can ARP with IP aliases on Windows be made to behave like on Unix?

On FreeBSD, when I have one interface with two IPs: ifconfig nic0 192.168.0.1 netmask 255.255.255.0 ifconfig nic0 alias 192.168.0.2 netmask 255.255.255.255 If I ping the alias, if the host I'm ...
1
vote
0answers
50 views

Duplicate entries in switch ARP table

A server is showing twice or more on my L2 switch ARP table Same IP address, mac address, and ethernet port. What could be causing this? Thanks
1
vote
0answers
65 views

ARP Tables on Windows vs Linux

I noticed on Windows Server 2008, Windows Server 2008 R2, and Windows 7 that IP multicast groups joined by a computer are recorded in the ARP table as static addresses automatically. However, the same ...
1
vote
0answers
357 views

VMWare ESXi 5.0 Networking Issue

I have an issue with 2 new ESXi hosts. OS - ESXi5.0 Custom Dell ISO patched up to Build 1024429 DELL R820 with 1G network 2 ports from integrated MB NIC(Intel) connected to 2 juniper switches, one is ...
1
vote
0answers
49 views

ipwatchd detects non-existing conflict?

Ipwatchd is telling me about a conflict that I just do not understand. As far as I can tell, there is no conflict. Am I reading the message wrong? It's a Xen machine with the following network ...
1
vote
0answers
55 views

Can you SNMP poll the ARP table on Cisco ACE?

I'm trying to get a MAC <=> IP mapping from a Cisco ACE. Unfortunately according to this table, while it supports IP-MIB the ipNetToMediaTable and ipNetToPhysicalTable subtrees are not supported. ...
1
vote
0answers
113 views

Keepalived, Junos, and ARP caching

I'm trying to configure an active-passive stunnel setup, with the aid of Keepalived, for a public IP address at our company datacenter. I would like to know if a router or switch reconfiguration is ...
1
vote
0answers
468 views

arp reply is not processed

My eth0 interface does not process a legitimate arp reply. When I try to ping a host, I see arp request and reply with tcpdump from the host I try to ping from, but ip neigh says that there is a ...
1
vote
0answers
189 views

Cannot ping any machine on local network (embedded linux device)

I have an embedded linux installation (custom built using buildroot, uClibc and busybox) and I am unable to ping any machine on my local network. My /etc/network/interfaces file is as follows auto lo ...
1
vote
0answers
169 views

stop arp poisoning on a 5448 powerconnect switch

We have to disable arp poisoning on our dell 5448 switch. Right now it has all our production machines running on it and I'm not a networking guy at all so I don't want to run a command that will ...
1
vote
0answers
107 views

What is the meaning of the QUEUE in arptables

I use the nfqueue target of iptables in order to get packet to the nfqueue and do some business rules on them. iptables -A INPUT -p tcp -j NFQUEUE --queue-num 0 I need to do the same on arp reply ...
1
vote
0answers
703 views

Arp request is not resolved

On my machine, I have assigned ip addresses for two interfaces which are connected through a cable. They are connected with 10G ports. When i tried to ping the two addresses, ping was not working. ...
1
vote
0answers
60 views

Server Core DNS Server in VSphere doesn't respond to ping and needs continuous arp clean

I have a VSphere installation hosting two Windows Server 2008 R2 installations. One of them is a complete install that serves as a DHCP server and that I use for administration. The other install is a ...
1
vote
0answers
288 views

virtualbox bridged adaptor works only guest->host but not host->guest

I have virtualbox 4.1 on a ubuntu 12.04 host. On my host I have a virtual interface eth0:1 configurend as 10.0.1.1. I have a few virtual machines using bridged adapters, configured in the 10.0.1.0 net ...
1
vote
0answers
277 views

Windows Server 2003 DC sends Gratuitous ARP requests with wrong IP

Hello and excuse me for my English please. ;-) Two server seems to be involved with this problem. Our DC (domain controller, 2003) an the VMware VC-Server (2008 R2). After capture "some" network ...
0
votes
0answers
16 views

How to fix stalled connection on large download

I have a cisco 1921 router performing routing and NAT function. Cisco 3750 is performing layer 3 core switching duties. Users are complaining about large file transfers being stalled (not dropped) ...
0
votes
0answers
20 views

X520-DA2 10GbE PCIe NIC on Ubuntu 12.04 doesn't respond correct ARP information for a traffic tester

I'm trying to configure stand-alone test network to examine a server that has two 10GbE ports PCIe NIC. But I couldn't get any ARP responses of those 10GbE ports. To execute my test, it's necessary to ...
0
votes
0answers
24 views

SYN-ACK with identical MACs

What could cause a CentOS machine to respond with SYN-ACK packet having both source and destination MACs set to the address of the NIC from which the packet is being sent?
0
votes
0answers
23 views

Strange network issue when moving EC2 elastic IP

Recently we had an issue with a Windows 2012 EC2 server, which meant that we had to move across to another instance. We duplicated the instance, ran some tests and moved over the elastic IP. Should ...
0
votes
0answers
78 views

localhost answering wrong ip

No idea how/why, but here's what I'm seeing. Consider 3 CentOS 5.10 boxes: Host A [10.1.2.7] Host B [10.1.2.8] Host C [10.1.2.9] All of a sudden we're getting strange behavior from Host X, ...
0
votes
0answers
119 views

Configuring VRRP with keepalived on two machines - interaction with proxy arp

Let's assume we have the following topology for our network: Host1------- Router1-------Router2----------Router3-------Host2 and we want to configure vrrp on the two hosts with keepalived so that ...
0
votes
0answers
100 views

Ubuntu 12.04 reply ARP request delay 10+ seconds

I'm running Ubuntu 12.04 in VirtualBox, my server program is running in it, its IP is 192.168.1.105. My client is running at 192.168.1.107. But the client alway took 10+ seconds to send a package to ...
0
votes
0answers
44 views

Router Advertisement loopback

I have a machine acting as a router. To send out router advertisements it is running radvd. IPv6 enabled. When an interface is enabled (e.g. a link-local address is set) radvd will sent to all nodes ...
0
votes
0answers
67 views

Redhat 6.1 LVS (DR) over private subnet

I am trying to run LVS on RHEL 6.1, but with traffic from the routers to the real servers over a private subnet. with direct routing (behold this drawing: http://i.stack.imgur.com/aJ22w.png) ...
0
votes
0answers
45 views

embedded linux is arping gateway periodically

I have embedded linux box, It sends arp to gateway periodically. If there is no connection with gateway, it sends more (3 arp request) permanently , and there is no ip packet going out from my linux ...
0
votes
0answers
345 views

Trouble directing traffic to Honeyd virtual hosts

I am trying to set up an experiment to observe some network behavior and as part of that experiment I am setting up a closed LAN that has virtual hosts created by Honeyd. I have honeyd running one ...
0
votes
0answers
158 views

Can't reproduce arp non-response issue with spoofed packets

I'm trying to debug an issue involving a KVM virtual machine instance where the instance doesn't respond to network requests when the source is on another physical machine, which is on the same subnet ...
0
votes
0answers
623 views

NETKEY IPsec and ARP

I'm wondering if I have the correct routing setup for an IPsec tunnel. I have control over the IPsec endpoints and the hosts connected to one side. These hosts are connecting to the tunnel so that ...