0
votes
1answer
55 views

How to use both bonding and bridge?

I have a server with two network adapters. I configured bonding and it works. Here's the working configuration: auto lo iface lo inet loopback auto eth0 iface eth0 inet manual bond-master bond0 ...
2
votes
2answers
199 views

Ubuntu 12.04 - Aliases of bonded interfaces not working correctly

I have the following /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet manual bond-master bond0 bond-primary eth0 auto eth1 ...
4
votes
1answer
999 views

LACP with 2 NICs working when either one is down, not when both are up

I'm running into problems with getting a LACP trunk to operate properly on Ubuntu 12.04.2 LTS. My setup is a single host connected with two 10 Gbe interfaces to two seperate Nexus 5548 switches, with ...
1
vote
1answer
719 views

Bonding linux - How to select mac address using mode 2 (balance-xor)

A few days ago, I wrote a question here, but that question was ambiguous. So, I will try rewrite the question, explaining all details. My previous message (closed message): http://goo.gl/aJqQ2 What ...
2
votes
3answers
2k views

Network bonding mode 802.3ad on Ubuntu 12.04 and a Cisco Switch

I am trying to team 3 network cards together on 2 servers. I am trying to achieve a maximum throughput of 3Gbps to replicate data between the servers. The setup is simple, I have 2 servers with 3 ...
1
vote
0answers
282 views

Ubuntu 12.1 Desktop and network cards bonding correct configuration

I have a computer with two network cards. From what I understand, I can use bonding to achieve greater throughput, so I followed this tutorial: https://help.ubuntu.com/community/UbuntuBonding Till ...
1
vote
1answer
262 views

Ubuntu Only Utilizes One Link in 802.3ad

I am currently using an Intel PRO/1000 PT LP Quad Port Server NIC with Ubuntu 12.04 LTS Server 64 Bit. I installed Gnome so I have a GUI. I downloaded bmon 2.0.1 to monitor the network, and right now ...
1
vote
0answers
404 views

Intel PRO/1000 PT LP Jumbo Frames in Ubuntu 12.04 LTS

I am having issues getting jumbo frames enabled in Ubuntu using an Intel PRO/1000 PT LP NIC with two bonded 1Gb lines. Following the readme that comes with the Linux driver, Ubuntu will not allow me ...
1
vote
2answers
1k views

Linux bonded Interfaces hanging periodically

I've several hosts that are showing problems with connectivity. When working from the command line, for example, typing is frozen for a second or so, then recovers - then it does it again. The most ...
4
votes
2answers
4k views

How do I put a bridge on top of a bonded interface?

I'm setting up a Ubuntu Server 11.10 box with multiple Ethernet interfaces that are bonded for redundancy. I'm planning to use it as a KVM host, so I'll need a network bridge. To accomplish this, I ...
6
votes
2answers
5k views

Does linux balance-rr (bond mode=0) work with all switches?

I'm configuring two ethernet interfaces into an aggregation group to double bandwidth, and I was wondering if bond mode=0 works for all switches? What about dumb switches that don't support LACP? Will ...
3
votes
2answers
1k views

NIC bonding can't go above 1 Gbps

I have 4-ports Intel 82571EB Gigabit adapter. It uses e1000e driver. The test machine is running Ubuntu 9.10, clients 9.10/10.04. I tried link aggregation (mode 4) and adaptive load balancing (mode ...
2
votes
1answer
251 views

Ubuntu 9.10 Network Bonding — randomly dies

I've run out of ideas with this problem, so thought a SF question may help. We've a number of Ubuntu 9.10 servers which we've recently switch from single NICs to bonded NICs using standard kernel ...