1
vote
1answer
22 views

Debian don't forward through L2TPv3 more than mtu l2tp virtual interface

R3--R1--Internet--R90 R3: ip addr 10.123.0.3 R1: sudo ip l2tp add tunnel tunnel_id 699 peer_tunnel_id 699 encap udp local 5.254.174.8 remote 5.254.174.90 udp_sport 699 udp_dport 699 sudo ip l2tp add ...
1
vote
1answer
27 views

NIDS on bridged firewall

I have a firewall (Debian Stable 7.5) which works in bridged mode. The interfaces eth0 (WAN) and eth1 (LAN) are linked with the bridge interface br0. Can I deploy a NIDS (eg. Snort) on this server? ...
0
votes
2answers
261 views

Setting Up Xen and Network Bridge on Debian 7

Setting up Xen and Network Bridges on Debian 7 Hi there. So i am finally going to try out some virtualisation on my new dedicated machine, however i am having some problems / confusion on setting it ...
0
votes
1answer
442 views

Xen dom0 not forwarding to domU over bridge

My setup is about as basic as you can get. I have 2 interfaces on dom0 (Debian Squeeze), eth0 and eth1. I created a bridge for eth1 to forward packets to domU that has a public IP address. I can ...
0
votes
1answer
407 views

How to bridge Network interfaces on Debian/kFreeBSD

I have had problems finding a way to bridge network interfaces on Debian/kFreeBSD. My primary goal is to create 2 - 4 tap interfaces and bridge them with two physical Interfaces. The Syntax in ...
1
vote
0answers
469 views

debian KVM - network bonding fails with vlan and bridge

i have a Debian 6 system configured with 2 NICs these NICs are used on a bond (bond0) which is used by bridge that require to use VLAN. i can get connection between guests running on VLAN10 but it ...
0
votes
1answer
145 views

KVM guest can't find gateway

I try to setup a KVM server with bridged networking. I followed the docs, but still can't get it working. The guest system can ping the host system and the host the guest system, so the connection ...
0
votes
1answer
738 views

VirtualBox Bridged Network to Debian Fails to connect [closed]

I am running Oracle VM VirtualBox Manager v4.2.0 r80737 on Microsoft Windows 7 and aiming to set up a bridged network to my Debian Linux 6.0 Virtual Machine to be able to connect to it via Local ...
1
vote
1answer
619 views

lxc vm access outside the host

On Debian 64bit, I configured a lxc like this : host ip : 172.16.0.25 vm guest on this host : 172.16.0.44 I've done the bridge on my host auto eth0 iface eth0 inet manual up ...
0
votes
1answer
278 views

Martian source in log of machine1 after ssh-DNAT to virtual machine located on machine2 (machine1 and machine2 xover connected)

My scenario 2 physical machines, each with 2 network interfaces (eth0, eth1). they act as virtual machine host for one machine alone, the networking works with no problems first i had two ...
2
votes
1answer
162 views

Access to WAN from one VLAN

i want to create a VLAN for 3 guest VMs. I already have it and every VM can ping each other, but the problem is that any guest CAN NOT have access to Internet Network configuration in Host machine # ...
0
votes
1answer
316 views

Debian bridged network between virtual machines

I installed two linux containers (lxc) in a debian squeeze server so the environment is as follows: Physical server: 192.168.2.200 Linux container 1: 192.168.2.201 Linux container 2: 192.168.2.202 ...
3
votes
2answers
2k views

Debian: Should I add vlan interface into bridge for KVM?

I am setting up a Debian Squeeze box as a KVM host. I want to add multiple interfaces to each KVM guest so I want them to be on different VLANs. After reading about this, I believe the best method is ...
1
vote
2answers
4k views

How to bridge a range of public IPs to KVM virtual machines on Debian/Ubuntu

I've been trying for weeks to figure out the right network configurtion for sharing a range of public IPs with KVM virtual machines running on my server, but so far with little luck and with the help ...
0
votes
0answers
922 views

Can't ping Ip over bridge

I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet ...
2
votes
3answers
1k views

KVM-Guests can't get past bridge - no internet connection

I'm running a backported KVM on a Debian Squeeze. ATM the KVM-Guest can't connect to the internet through the bridge I have set up. The guests can reach each other, the host but nothing outside. I can ...
1
vote
1answer
1k views

Virtual Box: Bridging to Virtual Interface (eth0:1)

I have four IP addresses on my Debian machine: 1 main (eth0) + 3 extra (eth0:0, eth0:1, eth0:2). I want to assign the eth0:1 as bridged network to my VM. Who do I need to add in the ...
0
votes
0answers
490 views

Install KVM on VPS how to configure network bridge

I want to install KVM on my VPS server, but I don't know much about setting up network bridges unter Linux (Debian Squeeze). In /etc/network/interfaces I have no eth0 controller, there is only # ...
0
votes
1answer
287 views

Is there a way to install L2TP and OpenVPN on one machine and bridge between both VPNs?

I am trying to install both OpenSwan-L2TP and OpenVPN on a Debian server and bridge between both server, is there a way to do that?
1
vote
2answers
671 views

Real life virtual bridge setup on Debian

How do I get the bridge setup done with multipe IP addresses. Ideally, I would have 4 virtual systems each with it's own IP address but also an intranet address (like 10.#.#.#). So that they can ...
2
votes
1answer
916 views

After configuring OpenVPN in bridge mode my serve becomes unreachable from an outside network

I have configured a Debian server with OpenVPN in bridge mode according to OpenVPN's ethernet bridging guide. As part of the guide I ran the bridge-start script which creates a bridge and tap ...
2
votes
1answer
2k views

KVM second private network (bridged), how to get working?

this seems to be a hard problem. I would therefore be very thankfull for your advice. I spend two days trying to get this running, but with no success. (The Public IP Stuff is working, but not the ...
2
votes
1answer
370 views

Using OpenVPN on Two Linux Machines *not on the gateways* to link the networks over the internet

I am running OpenVPN linking two linux machines on two networks. These machines are not the networks' gateways. There are also separate DD-WRT routers which are acting as the gateways on both ...
7
votes
2answers
915 views

Linux-KVM networking advice?

Being new to virtualization in general, and somewhat new to Linux (using Debian Squeeze and coming from BSD) I have a hard time understanding what would be the best network bridging option for my host ...
0
votes
2answers
305 views

Xen Bridge only working when IP Assigned

Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel ...
2
votes
3answers
11k views

Debian network bridge configuration - /etc/network/interfaces

I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl ...
2
votes
4answers
3k views

Instabilities with Bridged and bonded interfaces

I did post yesterday to get a working setup with several bridged interfaces used for virtual machines (KVM/libvirt). One of the bridged interface is just using eth3 as its ports while the second ...
2
votes
3answers
3k views

Issue with multiple bridging for KVM hosts

I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes ...
0
votes
1answer
2k views

Debian bridge networking restart fail

I'm having some difficulties getting my guests to see my host. When I'm trying to restart my interfaces I'm getting an error. sudo /etc/init.d/networking restart returns Reconfiguring network ...
2
votes
3answers
539 views

Constantly varying download rate with a complex xen networking setup, why?

The network configuration in my Xen setup is the following: the dom0 has 3 network cards (eth0, eth1, eth2), 3 brigdes (xenbrE, xenbrI, xenbrD) and each brigde integrates the corresponding network ...