Bridging is a forwarding technique used in packet-switched computer networks. Unlike routing, bridging makes no assumptions about where in a network a particular address is located.

learn more… | top users | synonyms (1)

2
votes
2answers
118 views

Disable IP on bridge

OK, I'm running libvirt on my server, I have only one interface. In order to use the public IP in my VM I need to set up a bridge, everything OK so far.. But I don't want to setup an IP address on the ...
8
votes
2answers
16k views

Bridging wlan0 to eth0

On arch Linux, I would like to mainly have eth0 (connected to bridged router) share the connection recieved from wlan0, Ive read tutorials but I'm not command sabby as other users are and don't ...
5
votes
2answers
6k views

Bridging LXC containers to host eth0 so they can have a public IP

UPDATE: I found the solution there: http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge#No_traffic_gets_trough_.28except_ARP_and_STP.29 # cd /proc/sys/net/bridge # ls ...
1
vote
2answers
125 views

How do I configure bridged networking for VMs

I'm setting up a KVM virtualization server in CentOS 6. How do I configure bridged networking? (I think I need network interface eth0 to be accessible to VMs) I have tried to follow this guide: How ...
3
votes
4answers
11k views

Split your DHCP scope among multiple servers?

I want to implement a redundancy solution. I have two subnets all windows XP machines - each with their own DHCP server - joined by a bridge. Currently - all machines get DHCP leases from the one ...
6
votes
3answers
7k views

Iptables - Bridge and Forward chain

I have setup ethernet bridge br0 that contains two interfaces eth0 and tap0 brctl addbr br0 brctl addif eth0 brctl addif tap0 ifconfig eth0 0.0.0.0 promisc up ifconfig tap0 0.0.0.0 promisc up ...
3
votes
2answers
2k views

Debian: Should I add vlan interface into bridge for KVM?

I am setting up a Debian Squeeze box as a KVM host. I want to add multiple interfaces to each KVM guest so I want them to be on different VLANs. After reading about this, I believe the best method is ...
3
votes
1answer
3k views

KVM network bridge with public static IP for both host and guests

I have a Ubuntu 10.04 server with 2 public static addresses. There is a KVM guest (also Ubuntu) installed and running. What i want is to give the guest an IP of the host, so that both machines have ...
1
vote
1answer
516 views

lxc vm access outside the host

On Debian 64bit, I configured a lxc like this : host ip : 172.16.0.25 vm guest on this host : 172.16.0.44 I've done the bridge on my host auto eth0 iface eth0 inet manual up ...
6
votes
2answers
1k views

OpenVpn bridge interface does not respond to incoming packets from outer network !

We are trying to set up a roadwarrior vpn setup with openvpn. We want the people to be able to connect to our network via openvpn. And we want them to be able to see and connect to the machines in our ...
4
votes
2answers
4k views

How do I put a bridge on top of a bonded interface?

I'm setting up a Ubuntu Server 11.10 box with multiple Ethernet interfaces that are bonded for redundancy. I'm planning to use it as a KVM host, so I'll need a network bridge. To accomplish this, I ...
1
vote
2answers
3k views

pfsense setting up as transparent firewall - dhcp issue

I followed the directions to set up pfsense in bridged / transparent mode per the instructions at http://doc.pfsense.org/index.php/Configuring_pfSense However I can not get a dhcp address from my ...
1
vote
2answers
1k views

Adding ip address to a bridge interface

Is there really any meaning attached for assigning a IP address to a bridge interface. Note : the bridge is created using brctl and then an IP address is assigned to br0 created. Is there any ...
3
votes
1answer
500 views

Network Bridge in dom0 can not ping domU's

I am using Debian wheezy with XEN 4.1. I have two network bridges xenbr0 and xenbr1. xenbr0 is linked to the real-eth0-nic so the domU's can talk to the outside world, which worked fine. xenbr1 was ...
2
votes
1answer
459 views

Why are eth0 and vmbr0 (bridge) having the same MAC addresses?

I configured my Debian (with KVM on board) as following: /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto vmbr0 iface vmbr0 inet static address ...
2
votes
1answer
601 views

Possible for linux bridge to intercept traffic?

I have a linux machine setup as a bridge between a client and a server; brctl addbr0 brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1 0.0.0.0 ifconfig eth2 0.0.0.0 ip link set br0 up I also ...
1
vote
1answer
187 views

Cross-VLAN sharing and auto-discovery of selective resources

I have a network with several VLANs that each contain resources or clients with different access rights. For simplicity, let's say I have 3 VLANs: ID 10: Contains privileged clients and private ...
1
vote
2answers
1k views

Xen network-bridge interface renaming

According to the comments in Xen's network-bridge script, the process of starting the bridge with external interface eth0 is thus: # Creates the bridge # Copies the IP and MAC addresses from eth0 to ...
0
votes
2answers
319 views

Why VM cannot get the public IP I have from provider?

I have a KVM-Host (on Debian) with root@kvm-host:/# cat /etc/network/interfaces auto eth0 iface eth0 inet manual auto vmbr0 iface vmbr0 inet static address 176.x.y.133 netmask 255.255.255.224 ...
0
votes
1answer
118 views

KVM guest has a wrong outgoing ip address

I have a KVM host with a bridge configured on eth0 that has a public ip: auto br0 iface br0 inet static address xx.xx.aa.111 netmask 255.255.255.0 network xx.xx.aa.0 broadcast xx.xx.aa.255 ...
0
votes
1answer
2k views

Use one NIC to create multiple interfaces for Linux KVM

I am working on a thesis research project, and I am having some difficulty figuring out how to make one NIC spawn several "bridge" interfaces such that each KVM VM can be seen on the local network. I ...
0
votes
1answer
1k views

Adding a bridge for my two guests in Debian with KVM

I'm trying to add a two tap0 and a tap1 for my to guests. I'm running Debian with KVM. Each time i restart the server after putting this in /etc/network/interfaces/ the server gets unreachable. Why ...