Tagged Questions

0
votes
1answer
67 views

EasyVPN vs Site to Site VPN bandwidth use

We have recently switched from site-to-site VPNs to EasyVPNs. At around the same time, we noticed increased bandwidth use. Does anyone know whether these two VPN methods use noticeably different ...
1
vote
0answers
49 views

CCP site-to-site VPN using access rules

I use CCP for creating site-to-site VPNs on a Cisco router. I need to use network objects on my ipsec rule for having multiple hosts but the network objects are only available on the access rules ...
0
votes
2answers
819 views

Ping Cisco ASA over VPN

ASA1 is 8.4(2) @ 192.168.1.1, behind this is host1 @ 192.168.1.10 ASA2 is 8.4(3) @ 192.168.2.1, behind this is host2 @ 192.168.2.10 Pinging form host1 to host2 works, but I can't ping that inside ...
0
votes
1answer
317 views

pfSense to ASA L2L VPN - infrequent, short-lasting, but consistent disconnections

Has anyone here been able to specify a stable configuration for the L2L VPN between an ASA device and pfSense 2.0.1? I am using the most accomodating settings on the ASA side (DefaultL2LGroup with ...
0
votes
2answers
310 views

How do I know if my site-to-site vpn connection is being saturated?

We've got a T1-internet connection with a Cisco ASA 5510 appliance in our small office. We have a site-to-site vpn connection from our office to a remote data center. Question(s): How can I find ...
0
votes
1answer
310 views

how to NAT site to site VPN web traffic?

I have 2 Cisco routers and they are connected via GRE over IPsec. All of the traffic from the first router is being routed to the 2nd router with a default route. I need to access internet from the ...
2
votes
2answers
106 views

Replace Cisco 2600 PTP T1

Our office and an outside location have a dedicated T1 point to point connected with Cisco2600's. We need to eliminate the need of the T1 circuit as it is costly and would like to route the traffic ...
1
vote
1answer
304 views

Replace a Cisco VPN IPSec concentrator with an Ubuntu-box

Is it possible to replace a Cisco VPN IPSec concentrator with Ubuntu and for instance Strongswan? 1) Do Strongswan implement the same protocolls that Cisco uses? 2) Can we retrieve keys from the ...
1
vote
0answers
528 views

Site B FXO configuration for incoming calls

I am trying to configure the FXO port (voice-port 4) on a Cisco SRST881. Currently, there is one working remote extension here (ext 50) and all calls originate from our main office. My goal is to ...
1
vote
1answer
293 views

Site-to-Site VPN between a Cisco router and a Linux box

SITE A A Cisco router (877W), configured for incoming VPN IPSec client connections Some servers, in a 192.168.0.0/24 network SITE B A Linux box with a physical NIC and a vpnc client ...
0
votes
1answer
2k views

Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up ...
3
votes
1answer
1k views

site-to-site VPN between cisco ASA and 870 cannot ping remote network

I have two sites which are connected through site-to-site vpn from cisco. One site has a cisco ASA router, the other has a cisco 870 router The tunnel has been setup, and active, however I cannot ...
1
vote
1answer
340 views

Site-To-Site VPN for internal traffic only

I'd like to connect my home network with my office network. At my office (host) I have a Cisco ASA 5510 ready to go. At my home network I'd like only work traffic to flow through the tunnel (meaning ...
0
votes
2answers
2k views

Giving VPN connections access to all locations?

I have asked a similiar question, but didn't get any answers so i am going to try and rephrase. i have 4 locations corporate and 3 remotes when you are at the corporate location, you have full ...
2
votes
2answers
707 views

Cisco ASA 5505 (8.05): asymmetrical group-policy filter on an L2L IPSec tunnel

I'm trying to find a way to setup a bi-directional L2L IPSec tunnel, but with differing group-policy filter ACLs for both sides. I have the following filter ACL setup, applied, and working on my ...
1
vote
0answers
666 views

Site-to-Site IPSec VPN: bridged only

I'd like to setup a site-to-site IPSec VPN tunnel between a head office and a branch office, and for political/security reasons, with the sole purpose of being able to access a "Management" subnet at ...
2
votes
1answer
911 views

Cisco ASA - VPN and Hairpinning

We have 2 sites that will be linked by a IPSEC VPN between 2 Cisco ASAs: Site 1 8Mb ADSL Connection Cisco ASA 505 Site 2 2Mb SDSL Connection Cisco ASA 505 Basically, both sites need access to a ...
1
vote
1answer
2k views

Route additional network through Sonicwall site-to-site VPN

I have a sonicwall site to site vpn. At one of the sites there is another Cisco vpn to another site. I need to route the traffic for the cisco vpn through the site to site from the other sonicwall ...
0
votes
1answer
419 views

Cisco / IOS Priority of VPN Tunnels vs EIGRP Routes

If I have two interfaces, one which gets its networks from EIGRP, and another that is an internet connection with VPN tunnels. If the same network exists for match address of the VPN tunnels and an ...
0
votes
1answer
1k views

Cisco ASA -> Windows 2003 site-to-site VPN

Is it possible to set up an ipsec site-to-site VPN between a Cisco ASA (5510) and a Windows 2003 Server? (using RRAS or similar on the windows server) And the followup question - if this is ...
0
votes
3answers
956 views

is it possible to set up site-to-site vpn with two CISCO881-K9

Is it possible to set up a static site-to-site vpn with two CISCO881-K9? One of the routers has a dynamic IP.
0
votes
2answers
954 views

pix 501 - site to site vpn subnet problem

I've configured a site to site vpn tunnel which is up and working as I would like. I have configured persistant routes on the pc's at each end that need to speak to each other. The subnets are as ...