0
votes
1answer
159 views

How do I connect two Cisco Catalyst 2950 over LAN?

I'm trying to connect (2) Cisco Catalyst 2950's over each's respective FastEthernet 0/1 ports, but for some reason, they're not communicating. I'm doing this to physically extend my network and add ...
9
votes
3answers
273 views

Native VLAN mismatch and missing VLAN?

I'm trying to wrap my head around what exactly is going on here with a new site's configuration of their networking stack. This particular piece I am working is pretty simple but I having a hard time ...
1
vote
1answer
198 views

How to enable Cisco switch port mirroring without rebooting?

I have a Cisco WS-C2960S-24TS-S switch and would like enable a port mirror for network analyzer (such as Snort). I could not see any options in the GUI interface. Is it possible, and how do I enable ...
0
votes
0answers
88 views

Need help setting up DHCP to give ips to different vlans

I need helping understand what am doing wrong. I am using Astaro UTM firewall software as my gateway, which is attached to a 3560 cisco switch. The switch as 3 vlan ( 20, 30, 40) and the firewall had ...
1
vote
0answers
89 views

Cisco Auto Smartports on catalyst 2960-s

I have Cisco Catalyst 2960-s, I want to configure user defined macros on it. I searched a lot in Cisco documentation but its not for beginners :( How to create a user defined macro that runs when a ...
-2
votes
3answers
102 views

Cisco switch inter-vlan access

I have Cisco Catalyst 2960-s switch and I want to configure three Vlans (A; B; C) I want to : Allow traffic between A and B Allow traffic between A and C Block traffic between C and B or if ...
2
votes
1answer
217 views

Spanning-tree setup with incompatible switches

I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and ...
7
votes
1answer
2k views

High latency/drops between Cisco switches in two locations. How to troubleshoot?

I'm receiving user complaints about poor network application performance between two parts of a large warehouse facility. The software is a curses-based terminal application running on a Linux server. ...
0
votes
1answer
453 views

Find client IP connected to VLAN from Cisco Catalyst 3600 by SNMP

I would like to get using of course SNMP, list of client IPs connected to VLAN in Cisco Catalyst 3600. So far, I have pseudo-algorithm made by me which obtains those IP addresses, but I am not sure ...
0
votes
1answer
171 views

Cisco redundancy modes

I am using a Cisco 6500 series with an SSO redundancy configuration. The show redundancy output is as follows: Hardware Mode = Duplex Configured Redundancy Mode = sso Operating ...
9
votes
2answers
3k views

Is my Cisco switch port bad?

I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck ...
2
votes
2answers
585 views

How do I draw a layer 2 (link layer) network map containing Cisco and *NIX boxes?

I've been tasked with drawing a layer 2 network map of our very small datacenter network. There is one 1841 cisco router, two 3560 cisco catalyst switches and 4 solaris sunfire T-1000 boxes. I have ...
1
vote
1answer
202 views

Cisco BPDUGUARD and BDPUFILTER

What happen if I have both ENABLED spanning-tree BPDUFILTER and BPBDUGUARD on a specific port?
2
votes
2answers
217 views

Multiple catalyst switches

We're about to do a major office move, which will involve re-cabling everything in our premises. We're in two floors of a single office building, with 2-4 comms cabinets on each floor; each of these ...