0
votes
2answers
178 views

Check RAID rebuild status of R710?

How can I check the rebuild status of a RAID volume without booting into the PERC utility in CentOS via the command-line?
-7
votes
2answers
333 views

Dell PowerEdge R710 - how to assign IP address to 4 available NICs and iDRAC? [closed]

I have a DellPowerEdge R710 server, brand new, with no configuration. How can I assign the IP address to its 4 NICs and iDRAC? Thanks! I would like to install ESXi 5.5 on that server and be able to ...
-2
votes
1answer
98 views

Should I install some OS on Dell EqualLogic PS4100 array to use it as storage only? [closed]

I have Dell PowerEdge Server R710 on which I installed ESXi. I also have a storage array, Dell EqulLogic PS4100. I would like to use my array as the storage only, I mean, using ESXi with vCenter ...
1
vote
1answer
76 views

Install ESXi for 2 servers on Dell Array

I have 2 Dell servers: PowerEdge R710, Dell PowerConnect Switch 6224 and an array: Dell EqualLogic PS4100. I need to install ESXi on my 2 servers. (Im just learning about VMWare, SANs, I have only ...
0
votes
1answer
444 views

How to connect to server with ESXi through the Internet? [closed]

I have a samll lab I can practice on. I have a Dell PowerEdge R710 with ESXi 5.5 installed on it. I have a Dell Juniper JSRX210 H and a management laptop. I also have the Internet connection (I simply ...
1
vote
2answers
1k views

Dell PowerEdge R710 ESXi installation [on which disk should I install?]

Im very new to the whole virtualization thing. I have a server that I can learn on, its Dell PowerEdge R710. I tried to install ESXi 5.5 on it. I booted from my CD with ESXi 5.5 I downloaded from ...
1
vote
0answers
183 views

Dell R710 Bios update - now does not display version [closed]

I was recently tasked with bringing two Dell R710's up to date with the latest BIOS and firmware patches. Both appeared to update fine, but after a reboot one is exhibiting some strange issues... ...
0
votes
1answer
639 views

Dell PowerEdge R710 enters BIOS setup during each boot

Our Dell PowerEdge R710 enters BIOS setup during each boot. We have to press Esc to continue booting. How can we ensure that the server boots without user intervention? During POST the server does ...
1
vote
1answer
783 views

ESX 3i Drive Assertion Fault on otherwise working system

The graphic (below) shows the fault I am seeing in VMWare Infrastructure Client, the drive0 light is also flashing. Not sure why, the other drive lights are green. Can't see any errors in the logs and ...
7
votes
1answer
7k views

Should I use bios “Advanced ECC” in Dell PowerEdge R710 Bios with ECC DIMMs?

I have a Dell PowerEdge R710 with dual Intel Xeon E5503 CPUs. It has 96GB(12x8GB) of ECC DIMMs. In its BIOS, memory is configured for "Advanced ECC". My question is if my DIMMs are already ECC, does ...
0
votes
1answer
248 views

dell idrac6 allow access to one IP address

I have a dell R410 with dell idrac6 (Integrated Dell Remote Access Controller 6 - Enterprise) which is in a data center in another country. I configured my idrac with public ip address but I have to ...
3
votes
1answer
477 views

Slow SMB/CIFS to/from Win2008R2 Server

Dell R710 w/ Intel 82576 gigabit NIC (latest Intel drivers). I'm setting up a new Windows Server 2008 R2 SP1 & so far I've installed updates & configured the File Services & Web Server ...
2
votes
2answers
2k views

R710 - DRAC Configuration IPv4

* Resolved by rolling back to DRAC6_FRMW_WIN_R279926.EXE * Having an issue with a new R710 where I cannot enable IPv4 on the iDRAC card. I have tried enabling IPv4 and setting static IP, Gateway ...
4
votes
4answers
2k views

PERC 6/i RAID on Dell R710: Slow disk… RAID10 on single controller?

There are multiple questions here - but it starts with this: we've a Dell PowerEdge R710 with a PERC 6/i RAID controller (or controllers) in a RAID10 configuration. The system is running Ubuntu ...