3
votes
1answer
46 views

Steady red light on 2 HP SAS drives in RAID 1

I have a HP ProLiant web server with two HP 300GB SAS SFF 2.5 inch drives (Model: HP 507127-B21). Both drives have a solid red light, however there is no indication within the management software that ...
2
votes
1answer
141 views

linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated ...
2
votes
3answers
5k views

Reinserted a RAID disk. Defined as foreign. Is import or clear the correct choice?

I have re-inserted a RAID disk, on a DELL server with Windows Server 2008. The drive-status indicator was changing between a green and amber light, and the monitor gave the following message: ...
5
votes
1answer
714 views

HP Proliant ML350 G5 SAS HDD

I am getting problem in HP Proliant ML350 G5. Some few days back one of the SAS HDD failed. It was 146GB SAS 15krpm HDD. We got new one which is 146GB SAS 10k rpm HDD. Its on RAID 1(1+0) ...
1
vote
1answer
193 views

Linux mdadm RAID5 data recovery with one drive failed, one drive failing

Improbably I had two drives fail in the same Raid5 array within 2 weeks of one another. Which means the array is dead. Yes yes hot spares not being lazy about replacing the failed drive I know. But ...
0
votes
1answer
1k views

Dell Open Manage physical disk failure predicted

I've installed the Open Manage Server Administrator on my Dell T100 to monitor RAID Controller and disks. From the Physical Controller report web page I see a table listing the two disks I have but ...
3
votes
1answer
1k views

Smart Array P400i Physical Drive failed after being replaced

We have replaced the bad drives in a few HP systems (ProLiant DL360 G5), but they continue to show failed. The drives are part of RAID, and I think this might be why they are appearing as failed. The ...
4
votes
1answer
1k views

Does a RAID 1 really protect from HDD failure?

If using a RAID 1 and if there are any inconsistencies between both disks found, data is copied from the primary disk (most likely the one with the lower port number) to the secondary disk. 1) But ...
2
votes
2answers
491 views

mdadm failure detected on one partition

I received this rather nice email today suggesting one of the drives in a RAID1 array has failed. A Fail event had been detected on md device /dev/md4. It could be related to component device ...
2
votes
3answers
4k views

S.M.A.R.T - Predictive Failure Count

I'm monitoring my IBM ServeRAID M5015 controller for RAID status with MegaCLI, I have this on one of the disk : Enclosure Device ID: 252 Slot Number: 6 Enclosure position: 0 Device Id: 14 Sequence ...
1
vote
1answer
9k views

Raid 1 disk failure recovery on Dell Poweredge 2850 - how to repair?

Ive just spotted an amber disk error message on my 2850, E0D76 BP drive 4 fail. Drives are ULTRA 320 SCSI. Its been a while since this server was set up so I cannot be abolutely sure my memory is ...
0
votes
2answers
852 views

Hard drives continuously failing in Fujitsu RX300 server

We look after a Fujitsu RX300 S4 server that has 6 x 500GB SATA drives in a RAID-6 array, running from an LSI MegaRAID card (built into the motherboard). A couple of weeks ago, one hard drive ...