The tag has no wiki summary.

learn more… | top users | synonyms

0
votes
0answers
16 views

need to exclude a static route from being redistributed into eigrp

I have some asymmetric routing and need to point a public IP back through my network. We are redistributing static into EIGRP. Does anyone know how to exclude a certain static route from being ...
4
votes
2answers
269 views

EIGRP neighbors flapping

I have a EIGRP topology set up in GNS3. It looks like this: The neighbor relationship between R7 and R8 is constantly flapping and I cannot figure out why. Hello timers and time delays are all set ...
0
votes
1answer
262 views

RIP Advertising Networks of EIGRP without Redistributing

This is the topology I have set up in my GNS3. The RIP V2 protocol of Router R2 is recognizing and advertising the two networks that are advertised in EIGRP, even though the said information should ...
0
votes
1answer
439 views

Are neighbors formed in EIGRP and OSPF always directly connected?

I always thought that neighbors formed in EIGRP were not necessarily directly connected because the only requirement for two routers to be neighbors is that they share the same Autonomous System and ...
1
vote
1answer
102 views

EIGRP Neighbor State

I understand that OSPF has states that describe the status of a neighbor (e.g. Init and Full). Does EIGRP also have similar information? I'm programmatically trying to get the status of an EIGRP ...
1
vote
1answer
1k views

Cisco IOS command : default-information originate vs redistribute static

I am quite confusing with the Cisco IOS command. what's the actual difference between redistribute static as i learn in EIGRP whereas default-information originate in RIP/RIPv2/OSPF? I hope to get ...
0
votes
1answer
488 views

Cisco 3750 - EIGRP not on common subnet problen

I'm getting lots of messages on a router IGRP-IPv4:(50)(Default-IP-Routing-Table:50): Neighbor 10.13.1.251 not on common subnet for Vlan11 10.13.1.251 doesnt respond and show ip route says ...
0
votes
2answers
73 views

what do we mean by Feasible and reporting distance?

what do we mean by Feasible and reporting distance ? i read many referance but i don't understand it if anyone have an example or picture to explain it in EIGRP
0
votes
1answer
1k views

EIGRP for Failover

Preface: Reading through O'Reilly's Network Warrior in the chapter "Ethernet Resiliency he describes the following Scenario (Trying to keep this in the limits of fair use): "Assume that the link ...
2
votes
2answers
548 views

EIGRP Unequal Cost Load Balancing

I am trying to configure unequal cost load balancing in EIGRP and am a little confused about a couple of parts. I have an ipsec gre tunnel using comcast, as well as a point to point t1 that I want to ...
2
votes
2answers
1k views

Using EIGRP to Advertise a VPN Tunnel Route

I have several routers all connected via a MPLS netowrk and one that is not. The one that is not part of the MPLS network is connected to one that is via a VPN tunnel. All the routers on the MPLS ...
0
votes
1answer
435 views

Cisco / IOS Priority of VPN Tunnels vs EIGRP Routes

If I have two interfaces, one which gets its networks from EIGRP, and another that is an internet connection with VPN tunnels. If the same network exists for match address of the VPN tunnels and an ...
1
vote
3answers
3k views

Slow Performance with MPLS

Background: My company is switching to an MPLS provider. The MPLS provider is providing both internet and MPLS. This is done with one ethernet drop by using two dot1q sub interfaces, one for the ...