Cloud service provider

learn more… | top users | synonyms

0
votes
2answers
149 views

Link rate between EMC DAE and HBA

I have a EMC DAE (KTN-STL4) drive cage directly connecconnected to a HP Proliant server using a QLogic QLE2560 HBA. I'm using copper cable between the HBA card and the DAE. On the controller card in ...
-1
votes
2answers
399 views

Can anyone identify the hardware/software called “EMC Flex 8-16”?

I have discovered a Description entry ("EMC Flex 8-16") in an systems audit which I can't identify. I have asked the Vendors, but have not yet heard back. I'll post an answer myself when I find out. ...
2
votes
1answer
886 views

EMC Celerra and Access-based Enumeration

I have a few CIFS shares for Windows on our Celerra, and I've run the EMCABE tool (in enable mode) on one of our CIFS virtual servers. When I check if ABE is enabled using the same tool, it comes back ...
1
vote
1answer
534 views

EMC ESRS stops working when it is VMotioned

EMC is on site and told me: The ESRS SAN monitoring solution will cease to function if that host is VMotioned In case anyone doesn't know, the ESRS is a dial home solution that works over IP. ...
1
vote
1answer
502 views

How do I find the date/time set on an EMC Symmetrix?

I'd like to find out what date and time (and possibly time zone) a Symmetrix (DMX-4 and VMAX) is set to. I've checked Powerlink as well as the man pages for symcli, but nothing pops out.
0
votes
1answer
704 views

EMC PowerPath Support Matrix

I know this is a stupid question, but I've found nothing online. Does anyone know where EMC has hidden the support matrix documentation so that I know what version of PowerPath is supported with ...
0
votes
1answer
184 views

Trouble with EMC vNXE and Cisco Catalyst Configuration for vSphere 5.5

Good afternoon, we have recently purchased -two Cisco Catalyst 2960-x switches -two Dell PowerEdge 320R server -1 EMC vNXE 3300-1 storage device I'm having a difficult time configuring the ...
0
votes
1answer
96 views

keeping the server name and IP address updated in the SAN

In the Navisphere's attached server report, the HBA UIDs are displayed along with the host names and IP addresses of the Linux and windows servers that were previously registered. The Servers now have ...
0
votes
1answer
532 views

Can the EMC grab utility be used on ESX hosts

Can the EMC grab utility be used on ESX hosts?
0
votes
1answer
383 views

is provisioning storage in VMAX difficult?

is provisioning storage in VMAX difficult? I am not getting any sort of training from my manager .There's going to be requests fro the clients in provisioning storage to their hosts (cluster, stand ...
-1
votes
1answer
1k views

EMC storage - set login/password VIA naviseccli command

I have two NETRA machines that connected to EMC storage ( EMC flare 28 ) I installed Solaris 10 on both NETRA machines my question - is it possible to set the login and password for EMC storage by: ...
1
vote
0answers
47 views

Does a dead LUN path cause an increase in I/O times on the remaining LUN path(s)?

We use an EMC SAN appliance. There are 2 'paths' from the cluster to the SAN. Today we experienced that one of the LUN paths was 'dead' (as reported in the windows event logs). Presumably the ...
1
vote
0answers
305 views

How to change / replace a failed “system” disk on EMC Clariion CX500?

On the first DAE, the first 5 disks are considered "special" because they host the OS of the storage array. One of those 5 disks is faulty : what is the procedure to change it? By the way, what ...
1
vote
0answers
105 views

Using EMC DAEs standalone

I've got a number of EMC DAEs filled with drives, for free. I'd love to use them, as they total to around 30TB, with possibly more available from the same recycling facility. As of right now I can ...
0
votes
0answers
29 views

VDI LUN and RAID Group design optimization

I have a shared storage SAN for our VDI environment that was configured in a specific way by a third party and I was wondering what (if any) was the benefit of the design. The SAN is divided into ...