2
votes
2answers
127 views

Linux RAID 1: How to make a secondary HD boot?

I have the following RAID 1 on a Centos 6.5 server: # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdb1[3] 974713720 blocks super 1.0 [2/1] [_U] bitmap: 7/8 pages [28KB], ...
0
votes
1answer
36 views

Use old raid drive as boot device without data loss

There were two disks in sw-raid. There were /dev/md1 as swap, /dev/md2 as boot and a /dev/md3 with ext4. The sw-raid was disabled by stopping and removing mdadm and then zeroing the superblock on ...
1
vote
1answer
315 views

How to boot after RAID failure (software RAID)?

Previously I had a software raid set up using (mdadm) of drives sda and sdb. sdb failed and the only way to reboot the system was by unplugging the second hard drive. Now I've added fresh sdb and sdc ...
0
votes
1answer
414 views

Grub can't find Xen multiboot file

I am running Debian Wheezy on a software RAID 0 with LVM. I'm trying to get Xen to work but grub refuses to boot in it. I installed Xen by following the instructions here: http://wiki.debian.org/Xen ...
0
votes
1answer
228 views

/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/sdam1

When upgrading the kernel I get: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/sdam1. Check your device.map. Auto-detection of a filesystem of /dev/sdam1 failed. Please report this ...
1
vote
1answer
107 views

Does Ubuntu 12.04 LTS support booting from RAID 6?

I'm setting up a new Ubuntu server using 12.04.2 LTS. I have five drives that I am setting up in a RAID 6 with LVM. Can I use this for bootup? Or should I make a separate RAID 1 partition for bootup ...
1
vote
0answers
81 views

Fresh debian squeeze software raid install wont boot

I am following these instructions: http://www.iprobot.net/linux-tutorial/how-to-setup-software-raid-in-debian-ubuntu/ (I used debian-live-6.0.6-amd64-gnome-desktop.iso and DD'd that onto a usb key, ...
2
votes
2answers
2k views

Cant boot newly created mdadm software raid in Debian linux squeeze

Hello I have very strange problem creating swraid on Debian Squeeze Linux. I started creating RAID1 from existing standard instalation of Debian on single drive. So I bought new drive and started ...
1
vote
3answers
2k views

Creating a partitioned raid1 array for booting a debian squeeze system

I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 ...
0
votes
2answers
192 views

Grub install devices & Software RAID

Server has a software RAID 1 (sda+sdb) configured as /dev/md0 device. Later system upgrade was launched and grub updated. Now it promped to select grub unstall devices from the list to finish update: ...
0
votes
1answer
185 views

Centos 5.5 SoftRaid Grub Installation

I did the Soft RAID 1 installation with Centos 5.5 on my server with 2 SATA 1TB disks. I followed this great guide here: http://wiki.centos.org/HowTos/SoftwareRAIDonCentOS5 However, there is one ...
1
vote
2answers
2k views

GRUB2 not detecting OS on raid partitions

I have recently added a drive to a system and have successfully raid'ed (RAID-1) the paritions, with the exception of the boot partition. I have it ready and mirrored, but can't get GRUB2 ...
1
vote
1answer
2k views

Rescuing grub on RAID+LVM

I have a dual SATA drive setup for a file storage/general purpose box, which is arranged thus: /dev/sda1 + /dev/sda1 = /dev/md0 RAID1 --> /boot /dev/sda2 + /dev/sdb2 = /dev/md1 RAID1 --> LVM with ...
4
votes
2answers
629 views

Setting up Linux softRAID10 so it can boot after a drive failure

I would like my RAID10 to survive the failure of the bootdisk. I want to write grub to the MBR of each disk in the array so that in the case of a failure the array will still boot on the remaining ...
1
vote
1answer
2k views

Getting Grub2 to recognize a Raid 10 boot/root

I've been trying to get my raid to boot from grub2 for about 2 days now and I don't seem to be getting closer. The problem appears to be that it doesn't recognize my raid at all. It doesn't see (md0) ...
1
vote
1answer
218 views

Fastest way to migrate Linux data

I'm looking for a fast to migrate Linux installation to another hardware. As I wrote in another question (http://serverfault.com/questions/110501/unable-to-access-resume-device-in-centos), I moved 2 ...
1
vote
1answer
2k views

Unable to access resume device in CentOS

I moved my CentOS soft-RAID1 drives to another box, and now it fails to boot. When I launched the boot process from the grub menu, I get the following error: "Unable to access resume device ...
19
votes
2answers
19k views

How do I tell if grub is installed on a device?

How can I tell if grub is installed on a disk, and if it is what settings it has (noteably, what it has for the root parameter) I need to check a lot of disks in software RAID1 arrays to make sure ...