1
vote
1answer
21 views

Transfer raided drive between to identical HP Proliant DL360 G5

I have two identical HP Proliant DL360 G5 servers with HP Smart Array P400i controllers. I want to move the drives from one of the servers into the other server. Will the controller of the new ...
1
vote
0answers
35 views

HP Dl360e Gen8 Not Detecting Hard Drives

I have a new HP Proliant DL360e G8 and it is not detecting the hard drives. We are using both non-hp, and official hp hard drives from an older server (DL120). Hard drives are 3.5" and they are not ...
0
votes
1answer
62 views

How to check HP Smart array status on ESXi 5

I've been reading How to run the HP Online ACU CLI for Linux in ESXi 4.x & trying to figure out a way to see the RAID status of the server without having to restart it. This is because, I've ...
2
votes
1answer
101 views

HP ProLiant with SATA/SAS Drives

I Currently have a DL350 G5. I have 4 74GB SAS drives in RAID that work fine but I tried to add a 1TB WD RED SATA drive for some storage and the RAID controlling isn't giving me an option to create a ...
3
votes
1answer
69 views

how to merge 2 controller (6 Bays each) in HP DL370 G6

I am having a server DL370 G6 as seen in the image below, and I want to install Windows Server 2008 E. we are using it for camera recording. Each slot has 6 2 TB hard disks. I want to merge both as ...
2
votes
1answer
220 views

CentOS 6.5 with HP ProLiant DL360e Gen8

I have a chance to install a new HP ProLiant DL360e Gen8 server. There are three hard drives. How do I configure RAID 1 on this type of server. Will RAID already be configured so that it will look ...
1
vote
1answer
119 views

Installing XenServer 6.2 on Proliant DL160G6 freezes during “Installing from base pack”

I'm trying a new install of XenServer 6.2 on an HP Proliant DL160G6 with a HP P410 raid card configured as RAID 5 over 4 drives, with a 256M BBWC. The install starts off properly, but when it gets to ...
3
votes
2answers
109 views

Switch disks between array controllers

I have an HP ProLiant ML 350 G5, which has an HP Smart Array E200i/128 BBWC Controller embedded. This controller manages two arrays (each with three 72 GB disks in RAID 5) This controller has ...
0
votes
2answers
72 views

Display HP RAID logical and physical drives sizes in megabytes

It does not seem possible to show more precises logical and physical drives sizes using hpacucli. For example, below I can only see sizes in TB and I cannot figure out how to display them in MB. ...
-5
votes
2answers
35 views

Drive fault was asserted DELL [closed]

i have a DELL PowerEdge 2950 Server whit raid for 3 HDD. A friend whit a HP Proliant server which has broken, come to my help, to save information from the hard drive only had. When i put on my server ...
3
votes
1answer
94 views

Multiple Servers, Multiple Drive Failure within 12 hours?

In the IT world I just won the Lottery Twice.... Today we had a hard drive fail in a raid array. A few hours later we had another drive fail on a different server.... We started checking all the ...
1
vote
1answer
139 views

Proliant DL320G5P, Embedded RAID controller: Windows installation shows phisycal disks, not logical drive

I am installing Windows 2012R2 on Proliant DL320G5P, with the Embedded SATA RAID controller. I have 4 disks, with two different RAID 1 (mirror) arrays. I have a "strange" situation: Windows ...
0
votes
1answer
478 views

HP Dynamic Smart Array B120i ESXi performance issue

One of our small offices was in need of a small server to perform certain tasks. Because the noise and size an of a regular server i went with the HP ProLiant Microserver Gen8 G1610T. Witch i expected ...
0
votes
1answer
124 views

Replacing a HP P410 RAID Card

I'm getting kernel panics and I'm suspecting it's the RAID card locking itself up based on the messages in the panic log. I'm not sure if it's really the card or not. When it boots back up, it says ...
-1
votes
3answers
102 views

Turn off RAID on HP DL380? [duplicate]

Can anyone tell me how I can turn RAID off on a DL380-G5. I just want the disks connected directly without any RAID as I want to use this to test Microsoft's software RAID. Can't seem to find ...
9
votes
2answers
366 views

Are consumer class hard disks okay for zfs?

I just recently bought a new server an HP DL380 G6. I replaced the stock smart array p410 controller with an LSI 9211-8i. My plan is use ZFS as the underlying storage for XEN which will run on the ...
1
vote
1answer
37 views

Raid 1+0 on HP ML350 G5

I'm trying to setup a Proliant ML350 that has a SmartArray E200i Raid controller. I want to setup RAID 1 but there isn't any option for it, just 0, 1+0, and 5. I only want to use 2 drives since I just ...
2
votes
2answers
179 views

Detect HP ML370 G5 Bad disk in RAID0

I have one HP ML370 G5 server. Which has four 146GB SAS disks and two 300GB SAS disks that are configured as RAID 0. I have encountered a problem with one of my disks. The windows server event viewer ...
0
votes
1answer
174 views

Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from ...
1
vote
3answers
278 views

How to identify faulty drive on a HP DL160 G6 - P410 Smart Array

I have a HP DL160 G6 Server with 4 HP SAS drive, firmware have been updated to the latest on the HD and the Smart Array... The issue im having is that one of the disk have a steady amber light turned ...
1
vote
2answers
160 views

How to move RAID 1 to RAID 1+0

I have two HP disks in RAID 1 (300 Gb), and would like to at 2 additional disks in RAID 1+0 having in total of 600 Gb on C:. I would like to know is it possible to do it using Array Configuration ...
3
votes
1answer
107 views

RAID 5 drive upgrade

We have an HP ProLiant ML350 G5 server with an 8-bay RAID 5 array configured on a Smart Array E200i controller. The system volume and data are on the same logical drive. The drives are 72GB each and ...
1
vote
0answers
335 views

HP P410 “Parity Initialization Status: Initialization Failed” How to fix?

I'm using HP P410 raid card with BBU with 12 x 3TB drives on RAID50 After a power outage at the datacenter, the hpacucli shows this: Parity Initialization Status: Initialization Failed However, all ...
2
votes
1answer
52 views

5 dead hard drives in a span of 2 months - what should I be checking?

So we got a nice new HP DL380 server with a fancy RAID card about one year ago. 2 months ago a hard drive failed. Thank goodness for RAID5... except that the RAID card only sort of worked and the ...
1
vote
2answers
591 views

HP P410 RAID CARD Issue - unassigned drives not detected by the OS

i just bought lot of HP DL180 G6 Servers, it's using HP P410 RAID Card, i plugged 12 x 2TB SAS Drives + 2 x 73GB SAS (for OS - RAID1) all drives showing up IN RAID Creating array page, so i just ...
1
vote
1answer
124 views

HP Smart Array E200i controller

Can HP Smart Array E200i 128MB RAID controller wotk without Posted-Write Cache moduler? It's battery have finished its life.
0
votes
2answers
77 views

HP P800 PCI controller disables(!) HP 410i internal controller

I have a HP DL360 G6 server with a very strange RAID controller behavior. I installed a P800 PCI RAID Controller card and all of the sudden I cannot access my hard drives that are connected to the ...
1
vote
2answers
54 views

HP p400i - 512MB RAID Controller card

Anyone know if the HP p400i raid controller can support multiple arrays? Say if I wanted a raid 0 with 2x146GB drives, and 3x300GB drives in a raid 5, both on the same card? Also, is it possible to ...
5
votes
1answer
172 views

Drives randomly dropping from RAID array

We have 3x 3TB WD Red drives configured in a RAID 5 on an HP P812 controller with the latest firmware on. However, drives keep being dropped randomly from the array upon reboots, though not always. ...
2
votes
1answer
2k views

Installing Ubuntu 12.04 on HP Proliant DL380e with 1TB SAS Drive

I have an HP Proliant DL380e with a 1TB SAS Drive and I am trying to install ubuntu server 12.04 on it. I have created a RAID array using Array Controller Utility and had a RAID0 logical volume ...
5
votes
1answer
582 views

HP Proliant ML350 G5 SAS HDD

I am getting problem in HP Proliant ML350 G5. Some few days back one of the SAS HDD failed. It was 146GB SAS 15krpm HDD. We got new one which is 146GB SAS 10k rpm HDD. Its on RAID 1(1+0) ...
2
votes
2answers
716 views

HP P410 ADU (hpacucli) generates empty report

I'm trying to monitor hard drive's smart status. I've tried smartctl tools and HP's own hpacucli to generate ADU report. However, neither of them are useful. smartctl does not show values like Power ...
1
vote
1answer
84 views

Using hpacucli to disable auto logical volume disabling when failed

By default, when a physical drive fails in an HP RAID array, the controller takes the logical volume offline to prevent data loss, instead of taking it in "degraded" status like LSI/Adaptec does and ...
0
votes
2answers
668 views

data lost with RAID5 on proliant DL360 when drives fail

For some reason the Array Controller on my Proliant DL360 G6 couldn't recognize 2 of the 6 750GB drives I am running in a RAID 5 configuration with VMware ESXi 5.1. When I rebooted the server I chose ...
5
votes
1answer
102 views

RAID Recovery after Firmware issue

This may be a duplicate but I think the situation is different. We were having problems with a HP MSA2000 SAN, speaking to support they suggested that we upgraded the firmware to the latest version ...
-5
votes
2answers
320 views

P812 “forgot” RAID6 - can't see disks at boot time in ORCA

We have an MSA60 with 12x4TB non-HP issue Seagate Constellation ES.3 drives connected to a P812/FBWC, on which I created a RAID6 over all of those disks with hpacucli and started to copy data on them. ...
1
vote
2answers
83 views

Install RAID1 without Second Hard Drive?

HP P410i Raid Card. I am waiting for a second hard drive to arrive. Is it possible to start with 1 hard drive and enable RAID1 without loosing data when the second drive is installed?
2
votes
0answers
89 views

HP DL380 G7 RAID controller detecting bays incorrectly - port or mobo?

I've been passed a DL380 G7 which appears to work fine (all usual checks come back OK, Linux boots OK, LV creation is OK and disk access is OK) -- except the left hand four bays connected to port 1 of ...
1
vote
1answer
240 views

HP 420i RAID raid level transform

I have HP DL360p Gen8 8 with internal 420i controler and FBWC + battery. ACU says that raid level is 1+0. But in details of the controler i've found: Mirror Group 0: physicaldrive 1I:1:1 ...
2
votes
2answers
629 views

HP smart array p400 RAID 1+0; two disks crashed

I am running a RAID 1+0 on a HP ProLiant DL360 G5 with 6 disks (each 146 GB). The mirror groups looks as follows: Group 1 146 GB 1-Port SAS Drive at Port 1l: Box1:Bay1 146 GB 1-Port SAS Drive at ...
3
votes
1answer
1k views

HP Smart Array P400 controller reports physical drives incorrectly

I've been researching on this the majority of the day, when I had time to blow. But now it's just becoming a headache, when I ask the HP P400 for detailed Information on the drives connected to the ...
4
votes
1answer
1k views

Accidentally deleted wrong logical drive HP Smart Array P800 controller

I was tasked to do some rearranging on my company's HP Proliant storage server. In the p800 configuration utility I managed to delete the wrong logical disk, which was a 10 disk RAID 6 array. I'm just ...
3
votes
1answer
3k views

Proliant server will not accept new hard disks in RAID 1+0?

I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ...
3
votes
1answer
874 views

Smart Array P400i Physical Drive failed after being replaced

We have replaced the bad drives in a few HP systems (ProLiant DL360 G5), but they continue to show failed. The drives are part of RAID, and I think this might be why they are appearing as failed. The ...
-1
votes
1answer
150 views

HP P410i RAID10 performance causing Xen to crash

It seems HP P410 RAID card is causing some of my servers to crash when under high IO. Configured RAID10 with 4x SAS 15k HDDs. Is this normal? Do I need some other hardware to add to the RAID card ...
8
votes
2answers
815 views

Can different drive speeds and sizes be used in a hardware RAID configuration w/o affecting performance?

Specifically, I have a RAID 1 array configuration with two 500gb 7200rpm SATA drives mirrored as logical drive 1 (a) and two of the same mirrored as logical drive 2 (b). I'd like to add two 1tb ...
-6
votes
1answer
66 views

Can i boot the server [closed]

Hello and good day. I have a ml350 g4 and i have these questions: I dont have the cpu-fan & heatsink does it need that to boot? Does it need the chassis fan to boot? What ram does it need? ...
1
vote
1answer
2k views

HP RAID array - hpacucli

I've noticed that one of the drives has "unassigned" status. Does it mean that it's a spare disk? # hpacucli controller all show config Smart Array P410i in Slot 0 (Embedded) (sn: ...
3
votes
3answers
1k views

What is the memory module on a RAID card needed for?

As above, what is the reason for needing a memory module on a RAID card? The card I am looking at (HP P410) comes with either 256MB or 512MB but unsure which to get and why.
6
votes
2answers
4k views

Disk/RAID Monitoring for HP Proliant Servers and Ubuntu 12.04

How can I monitor the status of the hard disks and the RAIDs of an HP Proliant server using Ubuntu 12.04. In Ubuntu 10.04 I could use the cciss-vol-status to query the RAID status periodically but ...