0
votes
0answers
47 views

network trouble with hp bl465c g7 and rhel6.5

I have an HP BL465c g7 that worked fine with RHEL6.3. After upgrading to 6.5 the network stopped working. Can ping itself but no the gateway or anywhere else. IPtables are clear, eth-tool reports a ...
3
votes
1answer
87 views

Network card location

I am generally familiar with hpacucli and hpasmcli but how do I determine in which slot a network card is installed? I need to be able to map to and from the slot and the MAC (and from there to the ...
1
vote
2answers
762 views

HP ProLiant DL380e Gen8 server - SPP use

I am planning to install Oracle Linux 6.4 on an HP ProLiant DL380e Gen8 server. I have been advised to use Service Pack for Proliant SSP DVD to install/update the missing utilities drivers for Oracle ...
1
vote
1answer
383 views

Red Hat 5.10 fail to boot on HP DL380 G7

I'm trying to install Red Hat 5.10 x86_64 on an HP DL380 G7 server, everything goes fine and I get the successful installation message but don't know why the server fails to boot! I've done the ...
0
votes
0answers
87 views

kernel: The lpfcdfc driver detected that no HBA ports are available

Got the following error in syslog on a hp server running redhat 6.2: kernel: The lpfcdfc driver detected that no HBA ports are available. I found nothing in the redhat knowledge base/ Customer portal ...
3
votes
2answers
504 views

RHEL 5.5 server has most devices listed as “Unknown Device”

When I run lspci on my RHEL 5.5 Server (HP ProLiant DL360p Gen8), most items look like this: 00:03.3 PCI bridge: Intel Corporation Unknown device 3c0b (rev 07) 00:04.0 System peripheral: Intel ...
8
votes
1answer
2k views

Can't Remove Logical Drive/Array from HP P400

This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The ...
0
votes
2answers
387 views

RedHat 5: HP Server ethtool not working

I am trying to check/change my network card speed settings with RedHat 5 and a Proliant G6 server from HP. On eth0 I can not really use ethtool - it just says Link detected. The network card is a ...
0
votes
3answers
253 views

Install Red Hat Enterprise Linux 5.5 on Proliant ML150 G2 server

I am investigating if I can install Red Hat Enterprise 5.5 on Proliant ML150 G2 server but I don't know if this configuration is possible. Is this configuration possible?
2
votes
1answer
952 views

HP ProLiant Support Pack (PSP) creates multiple grub entries

After installing HP's PSP 8.73 on RHEL5 with a G7 Blade, I end up with 4 grub entries 1 The Standard RHEL 2 HP (choosen as default) 3 HP hpahcisr 4 HP mptlinux I'm confused as to why I get all ...
1
vote
1answer
369 views

Redhat Kernel patching advice

An audit has pointed out that a RHEL server I manage has not had the latest kernel patches applied. I'm confused about kernel patching and within RHEL in relation to RHEL dot releases i.e 5.2 , 5.3 ...
1
vote
1answer
274 views

is there any conflict between HP blade system ProLiant BL680c G5 hardware and Redhat Linux Enterprise 5.5 or 6

We're going to install Linux Red Hat enterprise 5.5 on HP blade server that is connected to a part of SAN storage MSA 2000. I've tested both marked and unmarked sda option in partitioning. I did this ...
-2
votes
2answers
711 views

Red Hat 5.3 on HP Proliant DL380 G5 and failed drive on RAID controller

I have a development ERP server here in my office that I assist with support on, and originally the DBA requested a single drive setup for some of the drives on the server. Thus the hardware RAID ...
1
vote
4answers
1k views

execute switch command over ssh

I want to write a script that will log into several switches and check the status of several ports. I am running RHEL 4, and I have HP ProCurve 3500yl switches. I want to run something like the ...