1
vote
1answer
32 views

apt warnings with HP SDR/MCP repo on Ubuntu

I'm using the HP SDR system (MCP specifically) for Linux packages to manage the HP hardware RAID, iLo, etc. The kernel drivers for the hardware are upstream, so these are just management utilities. ...
1
vote
2answers
224 views

Video driver for HP DL380 G6 for Ubuntu 14.04

I'm trying to install Ubuntu 14.04 w/GUI on an HP DL380 G6 I found lying around - it has an ATI ES1000 graphics chip. After install the screen is very 'laggy' and only 1024 resolution (I have 1280 ...
2
votes
1answer
788 views

HP ILO utility for Ubuntu - hponcfg fails due to missing hp-ilo package

I'm working with an Ubuntu-based system running on an HP ProLiant DL360p Gen8 server. I prefer to install HP's management agents when I can for full hardware monitoring/configuration capabilities. ...
5
votes
2answers
530 views

How can I pass kernel arguments via PXE to an Ubuntu-like OS installer ISO?

I'm in a tough situation in which I need to perform a remote installation of a QuantaStor (Ubuntu-based - hiss) appliance onto hardware with limited out-of-band access functionality. The target ...
1
vote
1answer
240 views

Smartarray hpacucli command not showing individual drive status

Having a problem with the HPACUCLI cmd on linux, at boot a hp p600 card is reporting an error, but I'm unable to determine which drive it is. Instead of listing the separate drive status, I get one ...
2
votes
1answer
3k views

Installing Ubuntu 12.04 on HP Proliant DL380e with 1TB SAS Drive

I have an HP Proliant DL380e with a 1TB SAS Drive and I am trying to install ubuntu server 12.04 on it. I have created a RAID array using Array Controller Utility and had a RAID0 logical volume ...
0
votes
1answer
234 views

HP DL380 G3 and Ubuntu

I have bought a HP Proliant DL380 G3 and am attempting to install Ubuntu Server 12.04 LTS. My server's got two Ultra320 SCSI HDDs but in the Ubuntu installation process, the OS fails to recognize ...
6
votes
2answers
5k views

Disk/RAID Monitoring for HP Proliant Servers and Ubuntu 12.04

How can I monitor the status of the hard disks and the RAIDs of an HP Proliant server using Ubuntu 12.04. In Ubuntu 10.04 I could use the cciss-vol-status to query the RAID status periodically but ...
0
votes
2answers
169 views

Scanning on Ubuntu Server 10.04 LTS? [closed]

Fellow SF Linux users, I have a question for you. I'm currently trying to set up scanning with a HP LaserJet 3330, but I'm having a tough time. I was wondering how I can get Ubuntu Server 10.04 LTS ...
3
votes
3answers
306 views

Shutdown server, won’t startup

So, this is a little embarrassing. Just got a new server (HP ProLiant), installed Ubuntu, set an IP address, then wanted to move it into the server room. Used sudo shutdown -P now to shutdown, the ...
0
votes
5answers
4k views

HP Proliant ML110 G6 as first file server (RAID)?

Bit of a noobie and this will be the 1st server hardware I have purchased. We are a small design studio and I am about to buy our 1st server. I have successfully run Ubuntu on an old PC which has ...
1
vote
2answers
3k views

Should I use SW RAID / setting up RAID on HP Proliant server with Ubuntu

I have looked at a number of messages regarding software vs. hardware RAID here on SF but can't figure out which one I should use. The server I'm installing is HP Proliant ML330 G6 and the RAID ...
0
votes
4answers
3k views

Proliant Support Pack and Ubuntu on older HP Proliants

We have a couple of oldish HP Proliant servers -- one DL385 G1 and one DL360 G5, to be exact -- that we'd like to upgrade from CentOS 5 to Ubuntu LucidLynx. The problem is that HP doesn't offer Ubuntu ...