HP (Hewlett-Packard) is a server and network equipment manufacturer. This is a generic tag to be used when discussing HP hardware or software with no more specific tag available - See the list in the main tag wiki.

learn more… | top users | synonyms

3
votes
1answer
299 views

In a HP server, can low voltage DIMMS and standard voltage DIMMs be mixed?

We are adding RAM to a HP Proliant DL380 G7 and were shipped standard voltage DIMMS. We have pre-installed some low voltage DIMMS. Is it acceptable to mix DIMM voltage in general? Is it advised? A ...
4
votes
1answer
335 views

DDR3 10600 memory running at 533mhz

I bought a second-hand HP ProLiant DL160 G6 a year ago with 48GB configured in it. I discovered checking with cpu-z and doublechecked with speccy the memory runs at only 533Mhz. I checked the ...
2
votes
2answers
401 views

Combining SSD and HDD in HP dl380p?

I´m planning to buy a dl380p with 25 sff slots with 2 ssd:s raid 1 and 10 hdd:s raid 5, having room for 13 more hdd:s in the future. Is this possible or do I need two raid cards?
1
vote
2answers
8k views

stop error 0x0000007b on boot bare metal recovered Win2008R2

We had HP DL360G4p with Windows 2008 R2 which was broken a few days ago. I setup VM on ESX4 because we don't have extra same hardware and recover from WindowsServerBackup image. The recovery looks ...
2
votes
1answer
61 views

Hyper-V network dies after a few days of uptime

I have a Hyper-V server that randomly just drops off the internet in no specific pattern. It will go fine running five VMs that all have their own IPV4 in a /29 subnet. The host machine is on a ...
0
votes
1answer
2k views

Entering BIOS via HP iLo2 remote console

I want to enter BIOS remotely via HP iLo2 remote console. However, I tried to press F8,F10,Esc-8 and Esc-10. None of them works. Could someone teach me how to do so? Thank you. Regards, yuwen
1
vote
1answer
316 views

Access RBSU on ML350 G6 remotely

We have a remote server having issues and the HP Support guy suggested to "Disable No-Execute Memory Protection in the server BIOS." This is easy if you have the server onsite and there are many ...
4
votes
2answers
1k views

SAS enclosure doesn't restart - MSA60

I just inherited a HP StorageWorks MSA60 (this is a direct-attach SAS enclosure). I had to move it to another shelf so I turned off the computer which was using it. I also pulled the 2 power cords off ...
1
vote
1answer
149 views

How to change the size for HP smart array without losing data

For a HA clustered setup (RHEL 5.8), my HP DL 380p G8 server consists of this: mirrored root disk(RAID 1): array A physicaldrive 1I:2:1 (port 1I:box 2:bay 1, SAS, 300 GB, OK) physicaldrive 1I:2:2 ...
2
votes
1answer
4k views

Installing Ubuntu 12.04 on HP Proliant DL380e with 1TB SAS Drive

I have an HP Proliant DL380e with a 1TB SAS Drive and I am trying to install ubuntu server 12.04 on it. I have created a RAID array using Array Controller Utility and had a RAID0 logical volume ...
-5
votes
1answer
547 views

ESXi 5.0 - Software RAID 1

Environment: Storage: HP P2000 MSA G3 SAS Array with 24 300GB 10k SAS Disks Two Storage Controllers with redundant SAS connections to each host Hosts: Three HP DL380 G7s with a 10GB SD Card, ...
6
votes
2answers
2k views

Why are “sectors per track” still relevant on a modern OS with modern drives?

I am building out a new machine and the raid controller is asking me for sectors per track. I haven't had to deal with disk math in a long time (1998?), and I can't find anything that pertains to ...
3
votes
1answer
40 views

Raid 5 on two scsi buses with different maximum speeds

I'm quite a noob, I'm trying to set up as a study machine an old HP ProLiant DL385 G1. I've configured a RAID 5 out of six SCSI 3.5" HDDs using: - Smart Array 6i controller; - (4 x SCSI Ultra320 ...
2
votes
1answer
39 views

MSA2312i shows duplicate enclosures?

I just installed a redundant controller in my MSA70. This is in use with our old MSA2312i SAN. Now I'm seeing two entries for 'Enclosure 3' (the associated MSA70 disk shelf) in the UI. It appears ...
1
vote
2answers
514 views

Video driver for HP DL380 G6 for Ubuntu 14.04

I'm trying to install Ubuntu 14.04 w/GUI on an HP DL380 G6 I found lying around - it has an ATI ES1000 graphics chip. After install the screen is very 'laggy' and only 1024 resolution (I have 1280 ...
2
votes
2answers
1k views

Unable to create datastore extent on VMware ESXi 5.5 - HP Smart Array P800

I have a HP P800 array controller connected to a HP MSA60 with 12x 1TB SATA drives installed. I provisioned a single array with 1 spare in ACU. I have followed this KB and created 4x 1.9TB logical ...
1
vote
1answer
585 views

Installing XenServer 6.2 on Proliant DL160G6 freezes during “Installing from base pack”

I'm trying a new install of XenServer 6.2 on an HP Proliant DL160G6 with a HP P410 raid card configured as RAID 5 over 4 drives, with a 256M BBWC. The install starts off properly, but when it gets to ...
3
votes
8answers
11k views

HP ProLiant DL180 G6 Fan Noise?

Recently i did bought an HP ProLiant DL180 G6 Everything is OK except fan noise , it's too loud. I did some research but found nothing useful , I just wanted to know if there is anything I can do ...
2
votes
2answers
291 views

HP BladeSystem c3000 Enclosure : Ilo : Python : get_asset_tag() Not working

I try to connect to a HP Blade Server (HP BladeSystem c3000 Enclosure ) using Python's HP-ILO module. obj=hpilo.Ilo('172.8.2.29', login='Administrator', password='<redacted>', timeout=60, ...
2
votes
2answers
956 views

HP smart array p400 RAID 1+0; two disks crashed

I am running a RAID 1+0 on a HP ProLiant DL360 G5 with 6 disks (each 146 GB). The mirror groups looks as follows: Group 1 146 GB 1-Port SAS Drive at Port 1l: Box1:Bay1 146 GB 1-Port SAS Drive at ...
3
votes
1answer
105 views

how to determine which drive belongs to which slot on raid 5

i have an HP DL380 G8 machine with 4 hard drives of same size and running on raid 5. unfortunately during a service process of our data center one of the junior team members pulled out all four hard ...
1
vote
1answer
125 views

Transfer raided drive between to identical HP Proliant DL360 G5

I have two identical HP Proliant DL360 G5 servers with HP Smart Array P400i controllers. I want to move the drives from one of the servers into the other server. Will the controller of the new ...
1
vote
2answers
2k views

Cannot install Windows 2012 R2 on HP Blades

I have several HP ProLiant BL460c G1 blade servers where I am trying to install Windows 2012 R2. I was able to get it installed on one but can't get it installed on the rest. They all fail with the ...
3
votes
1answer
3k views

HP DL380 G6: Where is Temperature Sensor 30 (I/O Board Zone)?

In ILO2 firmware 2.15 on my DL380 G6, the Temp 30 sensor (location: I/O Board Zone) indicates 65C and my fans are running at 78% capacity. The Caution level for this zone is 110C, and the Critical ...
1
vote
1answer
437 views

Alternative system fans for EOL HP ML150 G6 servers

Background I have an HP ML150 G6 server that HP made 'End Of Life'. I added a second processor to the system but then was unable to get past POST due to a missing system fan. I found a diagram that ...
1
vote
3answers
734 views

Is it possible to see the RAM units configuration on HP ProLiant DL380 G5

I have an HP ProLiant DL380 G5 Server in the datacenter running Windows Server 2008 R2. I need to think about upgrading RAM on this server and decide on configuration of RAM units I am going to ...
1
vote
0answers
735 views

HP Dl360e Gen8 Not Detecting Hard Drives

I have a new HP Proliant DL360e G8 and it is not detecting the hard drives. We are using both non-hp, and official hp hard drives from an older server (DL120). Hard drives are 3.5" and they are not ...
0
votes
1answer
78 views

Is it possible to use a HP P410 Controller in a ML150 Gen5 server? i.e. is there a cable that interfaces with a Gen5 cage?

Specifically I want to use a SAS card (a P410) and some drives that I have spare in a ML150 Gen5 server. If there is a cable that converts mini SAS to the Gen5 SAS cage connection can someone point ...
1
vote
4answers
13k views

HP Compaq 8200 Elite SFF won't boot from USB drive

Can't get an HP 8200 Elite Small Form Factor to boot from USB. It's done so in the past & the USB boot drive works in a different machine (HP 8440p laptop). Have tried upgrading BIOS (from 2.09 ...
-3
votes
2answers
2k views

HP ProLiant DL380e Gen8 has high fan speed after installing second CPU

Today I installed a second CPU in our HP ProLiant DL380e Gen8, and after booting the fans all went to 99.96%. This causes the server to make an enormous amount of noise. Could it damage the server? ...
0
votes
1answer
159 views

Continuous I/O latency error on ESXi 5.0

Recently I posted a question on HP Proliant DL180 G6 - Smart Array P410, bay 11 error which the answers helped me to dig through. And today that I just noticed under my vSphere log which gives a ...
1
vote
1answer
507 views

HP DL380 G7 using P410 controller with a SAS Expander card

A sever is fitted with a HP SAS Expander card and 10x disks (2x mirrored Arrays). The server is not detecting any logical volumes or physical disks. So is it ok to bypass the expander card and ...
1
vote
1answer
1k views

HP SSD on ProLiant DL360p Gen8 p420i controller - no TRIM?

We have a HP Proliant Dl360 Gen8 server with the 420i 2Gg disk controller. (646905-421) we have a couple of the HP Gen8 200GB 6G SAS SLC SSDs (653078-B21), (they run in RAID1) We run Debian6 on this ...
2
votes
1answer
296 views

HP ProLiant DL360p Gen8 how to choose correct heatsink? [closed]

We purchased a new HP Proliant DL360 gen8 server (670640-425) (HP DL360p Gen8 E5-2620 Base EU) at the same time we purchased the cpu/heat-sink package for a 2nd CPU (654782-B21) (HP DL360p Gen8 ...
-1
votes
1answer
184 views

Difference of HP network adapter types?

HP have a special type of cards they call FlexibleLOM, and I can't figure out what the differences are of the following HP Ethernet 10Gb 2-port 530FLR-SFP+ Adapter HP Ethernet 10Gb 2-port ...
4
votes
2answers
966 views

How can I monitor HP P410 hardware RAID degraded in Freenas

I would like to run freenas on a HP P410 hardware RAID 5 4x600GB 15k SAS array and be alerted in the case of physical disk failure, however the freenas documentation says: to prevent problems, do ...
4
votes
1answer
836 views

HP ProLiant Gen8 Health Agents and EL6.x - cpqHoMibHealthStatusArray has changed to the value: x

I've noticed that my HP ProLiant Gen8 servers report the following message via email to root (or the destination configured in /opt/hp/hp-snmp-agents/cma.conf) upon restart. Trap-ID=11020 ...
1
vote
1answer
600 views

HP Proliant ML350 G6 Smart Error Test

I have a ML350 G6 with two array controllers : P410 and P410i. I have updated all possibile firmware on this server. I have 5 x Seagate Savvio 10K SAS drives. I am testing the drives with HP Insight ...
2
votes
1answer
656 views

HP ProLiant with SATA/SAS Drives

I Currently have a DL350 G5. I have 4 74GB SAS drives in RAID that work fine but I tried to add a 1TB WD RED SATA drive for some storage and the RAID controlling isn't giving me an option to create a ...
3
votes
4answers
2k views

HP Proliant DL180 G6 - Smart Array P410, bay 11 error

I've been trying to search over ther internet for a solution to fix this. I'm the new IT person for my organization and our previous IT have not kept any records on certain things. I do understand, ...
2
votes
2answers
849 views

HP ProLiant server - multiple raid controllers?

We just got a brand new HP DL370 G6 server with 14 X 146 gb and 2 X 300 gb sas drives. Inside we got 3 raid controllers (one HP DL370, one HP P410 and one HP P812). It has 2 disk bays and each of them ...
4
votes
1answer
4k views

Updating firmware on HP ProLiant DL380 Gen8 failed

I tried updating the firmware on my HP ProLiant 380e Gen8, but I received this error: What could be the reason? Could it be because of limited disk space in the /tmp directory? ~ # df -h ...
1
vote
1answer
90 views

How to migrate HP Service Manager?

I have built an instance of HP service manager in my Lab environment. I want to migrate the data in my old instance into this new one. It is built on top of a MS SQL-Server DB. I realize I can ...
26
votes
2answers
1k views

HP plan to restrict access to ProLiant server firmware - consequences?

I've been a longtime advocate for HP ProLiant servers in my system environments. The platform has been the basis of my infrastructure designs across several industries for the past 12 years. The ...
-1
votes
1answer
397 views

hp proliant dl380 g5 won't power up [closed]

Sorry for a probably silly question. I just bought an used hp proliant dl380 g5. It is supposed to be in a ready to use state. The problem is that it does not power up. The power green lights at the ...
4
votes
2answers
4k views

Broken BIOS detected, complain to your hardware vendor. WTF?

This is what I found in dmesg on my new Fedora 16 instalation on new HP ProLiant DL320 G6 [ 0.130963] Performance Events: PEBS fmt1+, Westmere events, Broken BIOS detected, complain to ...
2
votes
2answers
1k views

vSphere ESXi - Use both HP ProLiant DL360 G7 and DL360p Gen8 in the same cluster

I have vSphere cluster with few HP DL360 G7 servers, with Intel X5675 processor. I want to buy new server, HP 360 Gen8 with E5-2600 processors. Can I have this 2 kinds of servers in the same ...
1
vote
1answer
61 views

HP DL140 Lights-Out licensing issue

I have two HP DL140 and I recently upgraded their lo firmware. But one of them does accept the license but does not turn virtual kvm on. Do you have any idea?
0
votes
0answers
246 views

I am seeing error during boot sequence on HP ProLiant ML350p Gen8

The error states: Caution: Memory conflict detected. You may face boot problem. What steps would you recommend I take to troubleshoot this? Details: Dual Xeon E5 v1, two LSI 9286-8e ...
1
vote
1answer
770 views

logical drives on HP Smart Array P800 not recognized after rebooting

We had a Smart Array P800 configuration working fine (RAID5). Physically, we have a disk enclosure (like this) connected with a Linux Server. Here is what happened: This server was accidentally ...