HP (Hewlett-Packard) is a server and network equipment manufacturer. This is a generic tag to be used when discussing HP hardware or software with no more specific tag available - See the list in the main tag wiki.

learn more… | top users | synonyms

0
votes
0answers
13 views

hp proliant microserver not detecting hard drive

So, I've hit a bit of a wall with the HP Proliant Microserver N40L. I'm trying to install a new hard drive, 4 TB, but it's not being detected by the BIOS and thus, not the OS either. It just spins up, ...
-1
votes
1answer
15 views

HP ProLiant DL365 G5, USB and PS/2 Do not work during Boot

Good evening all, The situation up until the REAL point of failure; Dual Opteron 2300 Quad-Core (I'm not positive but I think theyre running at 2.6Ghz) 24Gb RAM (2Rx4 PC2-5300P-555) (lost 8Gb to a ...
2
votes
1answer
30 views

How do I install HP Smart Storage Administrator (hpssa) on a Proliant N40L running Ubuntu Server 14.10?

I have an HP Proliant N40L MicroServer with an HP Smart Array P410 raid card. The boot drive is an SSD running Ubuntu Server 14.10. The P410 is getting hung up while initializing. From what I've ...
7
votes
3answers
6k views

VMware - persistent “Host memory status” alarm in vSphere

I have a particular VMWare ESX 4.1 host that has a very persistent "Host memory status" alarm. This is running on an HP ProLiant DL360 G7 server. The HP ILO and System Management agents don't know ...
1
vote
2answers
3k views

HP Smart Array P400/256MB SAS Controller BATTERY

This is probably a dumb question. I recently purchased a couple of refurbished HP SB40C storage blade for our HP Bladesystem c3000 enclosure. Each comes with an HP Smart Array P400/256MB SAS ...
2
votes
1answer
2k views

hp DL380 G4 won't boot with disk plugged into front USB

We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the ...
5
votes
1answer
158 views

Expand RAID array on HP Dynamic Smart Array B320i controller

I have a few HP ProLiant DL360e Gen8 servers that are equipped with the Dynamic Smart Array B320i RAID controller. One particular system was shipped with a single disk installed instead of a pair of ...
2
votes
2answers
5k views

HP Dynamic Smart Array B120i ESXi performance issue

One of our small offices was in need of a small server to perform certain tasks. Because the noise and size an of a regular server i went with the HP ProLiant Microserver Gen8 G1610T. Witch i expected ...
-1
votes
1answer
27 views

What HDDs for HP Proliant Gen9 DL160, or suggest an alternative? [closed]

I'm currently looking at a replacement for our old server, running Server 2012r2. Its struggling. I was looking at the HP DL160 Gen9 and was wondering if I can use WD Reds with it? IT's for light ...
0
votes
2answers
564 views

Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from ...
0
votes
0answers
10 views

HP ProCurve 4208vl - Show PSU information?

I'm working with a few older HP ProCurve 4200-series chassis switches (4204vl and 4208vl). Some of these units have single power supplies, while others have dual power supplies. I'm trying to ...
0
votes
0answers
15 views

Automatically start machine if another fails

Is it possible to get a backup server (machine) to automatically start if the main server (machine) fails (i.e. does not longer respond to ping, or something). We're talking physical servers, not ...
-1
votes
0answers
12 views

How to add HP storevirtual storage on Vmware Vcenter [closed]

I have 3xHP Proliant DL380 Gen9 server and HP StoreVirtual 4530 storage, I want to add this storage server on Vmware vcenter, I already added my 3 server to Vcenter, but i cant add my storage, pls ...
1
vote
0answers
8 views

brocade 6520 san switch is not supporting in hp storage essential

I was trying "discover" Brocade 6520 SAN SWITCH in HP Storage essential, is not supported but the same configuration same speed switch "brocade 6510" is able to discover. how to make brocade 6520 ...
4
votes
3answers
4k views

Broken BIOS detected, complain to your hardware vendor. WTF?

This is what I found in dmesg on my new Fedora 16 instalation on new HP ProLiant DL320 G6 [ 0.130963] Performance Events: PEBS fmt1+, Westmere events, Broken BIOS detected, complain to ...
1
vote
1answer
401 views

HP Proliant 380 G4 iLO stuck in recovery mode

The iLO interface on this server is stuck in recovery mode. I've tried flashing the firmware via FTP per the iLO manual. It seems like the flash succeeds & the iLO interface resets, but it comes ...
1
vote
0answers
23 views

Ubuntu dd test becoming slow over time under ESXi 5.5

I have a HP DL320e running the custom HP build of ESXi 5.5.Guest is a Ubuntu server 14.04 with vmware tools installed. Write speeds to the two SSDs in RAID1 (disk added with thin provision) are great ...
7
votes
1answer
117 views

Automated hardware testing of HP servers?

As part of provisioning servers we run HP's Insight Diagnostics to test the hardware. This is a manual process. Is there a way automate the running of Insight Diagnostics? There is the hpdiags ...
1
vote
1answer
16 views

MSA60 fault light on while not faults showing in ACU

I have a MSA60 with the front side fault light on as well as the back side. No individual component has a fault light on. I check the Array Configuration Utility (ACU) and there no faults. The MSA ...
7
votes
3answers
985 views

What is the name of this screw? (from HP ProLiant quick-deploy rail kits) [closed]

I need the name of the screw for the HP quick deploy rail kit. The screw clicks into the square holes of the rack. It is a Gen4 Rail kit but the screw is like the Gen8 Rail kit ones. I called HP ...
2
votes
2answers
1k views

Get port vlan tag via snmp on HP Procurve

I'm trying to write a nagios check that will check if a port is a member of (tagged in) a perticular VLAN. I've discovered the following SNMP location SNMPv2-SMI::mib-2.17.7.1.4.5.1.1.40 for checking ...
1
vote
1answer
17 views

Which print driver do I deploy? What is a print driver capable of?

My organization recently purchased a HP DesignJet T3500 printer with the HP Designjet PostScript/PDF Upgrade Kit. HP offers 3 specific drivers in 2 packages. Which driver do I use? When I run the Add ...
1
vote
0answers
13 views

Server deployed without HP Intelligent Provisioning. How do I bring up to spec?

I have a few servers that were configured without HP Intelligent Provisioning, possibly because the datacenter was without Internet access at the time. Is is possible to reliably, and consistently ...
0
votes
2answers
856 views

HP Proliant DL320 G5 Memory Registered or Unregistered?

I have an old HP Proliant DL320 G5 with 2x 1GB of RAM. I would like to swap out the old ram and install 4x 2GB of RAM to bring it to the max capacity. The manual calls for PC2-5300 unbuffered modules. ...
2
votes
2answers
3k views

HP ProLiant Smart Array “lock up” code 0x11

I've a ProLiant DL580 G7 server that experienced a storage subsystem failure during production. The system appeared available and responded to pings, but all I/O access stalled (the system load must ...
9
votes
1answer
3k views

Admin mode on Procurve Switches

Not being a network expert, I spent some time configuring my network, until I found my mistake: On my HP ProCurve Switch 1810G, I thought that "Admin mode" means whether the administrative interface ...
1
vote
2answers
744 views

Alternative system fans for EOL HP ML150 G6 servers

Background I have an HP ML150 G6 server that HP made 'End Of Life'. I added a second processor to the system but then was unable to get past POST due to a missing system fan. I found a diagram that ...
-3
votes
1answer
37 views

raid 1 & ml350 gen8 server with centos 6.2

I have a proliant ml350p gen8 HP SERVER with centos 6.2 and two hard disk with 1 TB for both. I have several GB of files and software about 100) with their configurations but I want to install RAID 1 ...
-3
votes
1answer
34 views

HP ProLiant DL360 Gen9 - server to server connetion [closed]

Just want to know if I can do a server to server connection via Cat6 cable for: HP ProLiant DL360 Gen9 thanks
1
vote
1answer
536 views

HP ProLiant DL380 G6 with 2 x Intel x5650 CPUs

I have an old HP DL380 G6 server, I am trying to upgrade the processor. I added 2x X5650. but each time I powered the server on, the fans stat working loudly and keep like that. the server never never ...
1
vote
2answers
45 views

No LUN available to extend datastore

I have a HP DL380G5 with ESXi 5.5 and x4 146GB Sata disks in a RAID5 array. I have added one more disk to the server exactly as the other ones and, using SmartStart CD I managed to add the disk to the ...
0
votes
2answers
2k views

HP MSA2000, how detect faulty disks?

I have an HP MSA2012fc, it happened a few times that my large vdisk (6x 1TB raid 5) get offline, seems some disks are faulty, the event log only shows 2 of the drives had "bad blocks" and some disk ...
0
votes
4answers
70 views

How can I find out what RAM is in my ProLiant DL380p?

I know what RAM is compatible with my server, but without taking the lid off I don't know what specific modules I've got. It took two seconds to find out from vSphere that I've got eight(8) 8GB DDR3 ...
2
votes
1answer
3k views

CentOS 6.5 not booting after installation on Hp ML310e Gen8

I have experience with Installation and configuration of Windows Server system. I am trying to install CentOS 6.5 on the above mentioned HP box and the installation process goes on without a hitch. ...
4
votes
3answers
1k views

Extend RAID 1 (HP SmartArray P410i) running Linux

I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) ...
0
votes
1answer
151 views

Can HP Proliant server be set to use no RAID?

I recently purchased 2 HP Proliant DL380 G6 servers for the purpose of virtulization; each will be a new host in our VMware environment. I know that I will get heat for this, but I do not want to use ...
0
votes
2answers
101 views

auth on msa2324fc via xml api failed

I'll try to use my script ( which has been written for msa p2000 g3 ) with old san array msa2324. It seems like array actually do authorization and return session key, but my next request ( with ...
1
vote
1answer
50 views

SAS drive replacement in Proliant server and compatible drives

I am use an Prolian Server ML350-G5. The server has got two disk in RAID 1+0. The model of the disk is 432320-001 (146GB). One disk has shown an ambar light that means the disk needs to be replaced ...
2
votes
2answers
3k views

How to change hard disk array on HP Proliant ML 350?

We have a hd damage and we need to replace this hd, How to change and add more hd to array to HP Proliant ML 350 G5 server ?
-1
votes
0answers
9 views

Can I run HP UFT/QTP on AWS from license point of view? [duplicate]

Google does not know much about it. Can I run HP UFT/QTP on AWS from license point of view?
0
votes
0answers
153 views

Connection problems with Microsoft NIC teaming

I've got three HP servers: DL380G7 running Hyper-V Server 2012 DL120G6 running Windows Server 2012 DL120G7 running Windows Server 2012 R2 Running various Hyper-V VMs and also running many ...
2
votes
2answers
117 views

ProLiant ML310e GEN 8

I have a ProLiant ML310e GEN 8 that always shows early system initialization on startup, and never gets past 90%. It also has the status code 0114 down in the bottom right hand corner. Steps I have ...
2
votes
4answers
281 views

What features of a HP DL server make it so much more performant than commodity hardware?

I've used HP DL machines at work. I found them to be blazingly fast, but very expensive - up to $15k, I am curious though, although the spec we typically used (e.g. dual AMD Opteron 2.6GHz, 8 or 16GB ...
1
vote
1answer
857 views

HP Server attention light is blinking?

We have an older HP Server RP2470 running HP UX. I've been assigned to perform some hard drive clean up and OS Maintenance on the server before we move it into production. Everything is going just ...
2
votes
1answer
1k views

Why isn't my RAID array rebuilding?

Got a notice last night that a drive failed on a server. Got in this morning to replace it, and we're getting the following. Controller config report for the array looks fine, with the unusual status ...
7
votes
4answers
5k views

How to make my HP server boot faster?

I have an HP ProLiant DL370 G6 server that I am using as a workstation. It takes 60 seconds during reboot and cold boot before screens post with a discrete Radeon HD6xxx GPU. What can I do to make ...
1
vote
3answers
88 views

HP ProLiant disk failure, proceed or do not proceed

We have a HP proliant DL385 G7 server that’s a vmware ESXI host with a failed hard drive – the drive is a HP SAS-MDL, 7.2 K, 2TB. When we boot the server we get the attached message and we are not ...
-2
votes
2answers
96 views

HP proliant SE316M1 G6 drivers for windows server 2008 R2

I have a HP proliant SE316M1 G6 and we have just installed windows server 2008 R2 the machine didn't come with any drivers and i can't seem to download any windows server seems to have found most of ...
14
votes
3answers
8k views

What happens when the USB key or SD card I've installed VMware ESXi on fails?

An SD (SDHC) card installed in an HP ProLiant DL380p Gen8 server running VMware ESXi just failed :( I encountered some ominous looking messages on the vCenter console and in the HP ProLiant ILO event ...
1
vote
1answer
26 views

Finding out which cciss disk is what /dev/sdX disk (smartmontools & cciss raid controller)

I have a HP server, which has a hardware RAID array (that mostly isn't being used for raiding, the disks are just passed through to the Linux OS). I have 6 SSD disks. 2 are riad mirrored together by ...