1
vote
1answer
105 views

Howto configure Raid on IBM x3500 m3

I have recently acquired an old IBM x3500 m3 and I'm struggling to find the raid configuration. I've checked out everything in the uefi and post doesn't show any key combinations to access ServeRaid. ...
0
votes
0answers
30 views

IBM x 3650 M4 - enable disk slots 4-7

I have a x3650 with a ServeRaid 5110 controller. I have six disks installed - first 3 as one RAID5 array, and I want to set the second 3 up as another RAID5 array. However, only slots 0-3 seem to be ...
1
vote
2answers
209 views

M1015 pass-through and hot-swap in Linux with md raid (IBM x3620)

I'm setting up a small, but hopefully durable server for a student community, and the hardware is an IBM x3620 M3 with a builtin M1015 RAID card. To make the setup future proof and avoid vendor ...
1
vote
1answer
98 views

IBM serveraid problems

When I start my server serveraid gives me this error: not responding properly Error 00D0 any help would be appreciated. I can't find any information on this. Where can I go to get more information on ...
0
votes
1answer
539 views

IBM ServeRAID 8k level 1 critical

This is my setup: Lenovo ThinkServer RD140 IBM ServeRAID 8k controller Four Seagate Barracuda 1TB hard discs, organised in two RAID-1 arrays Now the third disk is defunct (orange light flashing). ...
2
votes
3answers
5k views

S.M.A.R.T - Predictive Failure Count

I'm monitoring my IBM ServeRAID M5015 controller for RAID status with MegaCLI, I have this on one of the disk : Enclosure Device ID: 252 Slot Number: 6 Enclosure position: 0 Device Id: 14 Sequence ...
0
votes
2answers
322 views

ServeRAID 8i setup

I purchased a second hand IBM eServer x345 with ServeRAID 8i and 3x 36GB SCSI hard drives. I'm having difficulty setting up an operating system as the drives don't appear in either Arch or Ubuntu ...
0
votes
2answers
2k views

Email alerts when RAID fails on IBM server?

Have two RAID controllers on an IBM server (X3500 M3) running Windows 2008R2: ServeRAID M5014SAS/SATA Controller LSI Adapter, SAS 3000 series, 4-port with 1064E Can anyone explain how to get email ...
1
vote
3answers
4k views

What does Quick Initialized RAID status mean?

We have re-created RAID1 on our IBM X3400, with the 8K-l RAID card, and now the RAID1 is in status of Quick Initialized. I've read online that the performance of this status is might not be optimal, ...
2
votes
1answer
1k views

IBM ServeRAID bad stripes and synchronize

After one of the drives in our IBM RAID gone, we bought a new one and replaced it. The rebuilding went fine, but now we see "Bad stripes" reported for the logical disk. Moreover, some data can not be ...
0
votes
2answers
1k views

IBM ServerRaid 8K and Sata1 issue

I have a X3400 with 8 x (43w7598 250GB SATA 3GB/S HDD) set in the frontal bay and connected to ServeRaid 8K controller. The raid array works well but, even if I set the controller PHY to 3.0 (rather ...
1
vote
1answer
3k views

X345 and ServeRaid 5i - Defunct Drives

I have an old IBM X345 server with a ServeRaid 5i card that I was running as a fileserver/test-server. It was running VMWare ESXi 3.5, with a virtualised OpenSolaris machine inside of this this (as ...
0
votes
1answer
258 views

Can an IBM ServeRAID 4mx controller work on a non-IBM server?

I have some IBM ServeRAID 4mx controllers on some aging IBM x360 servers (Pentium III 1.5 ghz CPUs); I also have a SCSI disk array with two ports, which can be attached to those controllers; and I ...