2
votes
1answer
75 views

Linux bridging for KVM

I have a Debian Wheezy machine on which I tried to setup KVM with bridged networking. Unfortunately, the bridge does not appear to forward traffic correctly. My setup is the following: The physical ...
1
vote
1answer
40 views

KVM virtualization with two bridges, want routing to use each bridge as mapped in KVM

I can't seem to find an existing question like my scenario. I'm using 2 public bridges for 4 VMs. Two VMs per bridge device. Interface stats show there is use of the assigned bridge for the VM on ...
0
votes
0answers
25 views

KVM Networking guest issue due a provider networking limit

I have a KVM setup on Centos 6.4 64 Bits. My server provider assign us a Main IP to the Host with a gateway and netmask. Also our provider assign us additionals IP ( not in the same block as the Main ...
2
votes
1answer
60 views

KVM bridging for virtual machines is not working

After restarting the server, I can not ping and reach my virtual machines from the net and vice versa [root@pc1(192.168.0.114) ~]# ping 192.168.0.63 PING 192.168.0.63 (192.168.0.63) 56(84) bytes ...
0
votes
1answer
107 views

Ping (DUP) with Linux bridges and tap devices

http://imgur.com/qPoy2QJ I have two Linux (Ubuntu 12.04) VM (running on KVM) that networked together using two Linux bridges as shown above. The network interfaces are Linux TAP devices. The problem ...
1
vote
2answers
174 views

How do I configure bridged networking for VMs

I'm setting up a KVM virtualization server in CentOS 6. How do I configure bridged networking? (I think I need network interface eth0 to be accessible to VMs) I have tried to follow this guide: How ...
0
votes
0answers
112 views

Access KVM guest via hostname on private virtual network

KVM on CentOS 6.5. Setup one bridge connected to internet. And one virtual network on subnet 192.168.100.0/24 DHCP start: 192.168.100.128 DHCP end: 192.168.100.254 How to ...
0
votes
0answers
35 views

Forward connecting IP address to KVM guests

I'm running kvm with iptables configured to use DNAT and masquerading. However the guest machines are logging the host bridge ip not the connecting client IP address. Is there a way to configure ...
2
votes
1answer
265 views

Ubuntu/KVM Bridge Interface IP Assignment

I have a Ubuntu 12.04 LTS machine running KVM/libvirt. It has two physical ethernet interfaces. I have dedicated eth0 as the primary interface and configured bridging on eth1 for my VMs. The KVM host ...
0
votes
1answer
119 views

assign public IPs to vm guests

I have a set of public IPs for virtual machines. Each unique public IP is to be assigned to a unique guest. With bridged networking I share eth0 with KVM machines. The ifcfg-eth0 file has ...
2
votes
2answers
543 views

How to assign multiple public IP address for 3 KVM guest using a single NIC [closed]

i've a CentOS 6.5 KVM Host with 3 KVM-Guest CentOS 6.5. Now I want to assign a public IP for the host and one public IP for each guest using a single network interface. My IPs (assigned by network ...
1
vote
0answers
64 views

Bridging Adapter in Ubuntu 12.04 LTS for KVM

Fresh install of Ubuntu 12.04 LTS with libvert/KVM installed. I have 2 virtual machines that I need need to be on the same LAN as the host. The host has two physical interfaces eth0 and eth1. eth1 is ...
0
votes
2answers
41 views

My KVM machine can't get the network

I'm setting up a virtualization server for my company based on Fedora 19 and KVM. Our goal is to being able to convert and run a bunch of VirtualBox VMs. So I setup my F19 server, and created a br0 ...
1
vote
1answer
699 views

Assign ipv6 address to KVM guests on bridge mode

System: CentOS 6.5 Network: Bridge on br0 IPv6: ISP Native /64 block. IPv4: ISP address (not internal LAN) Purpose: To assign IPv6 only to guests (manually), I don't want ipv4 address to be ...
1
vote
1answer
71 views

Prevent hijacking IPs in a bridged network (KVM/libvirt)

Is there a solution to prevent a VM user assign/use IP addresses he doesn't own but are routed over the same bridge like his own addresses? The current setup looks like this with libvirt and KVM: ...
1
vote
1answer
2k views

Multiple, different VLAN trunks to KVM guests (Linux)

I've hit a roadblock of sorts with an architectural challenge. I've got a server running KVM - which will feature a number of guests, some running virtualised firewalls and others, just plain web ...
0
votes
1answer
100 views

libvirtd - Getting vps to use existing bridge

I've been working on getting KVM running on CentOS 6.4 and ran into a snag. After pouring through several online docs about setting up a bridge for the vps to connect to, and manually attempting to ...
0
votes
2answers
416 views

bridge networking KVM

i am having a problem connecting VMs to the bridge interface. My VMs cannot connect to the host and LAN outside the host, when i ping it just say destination host unreachable. it seems that my VM is ...
0
votes
1answer
92 views

Ubuntu 12.04: KVM and assigning public IPs to VMs

I'm setting up an environment where I have a VM host running behind a NAT firewall and plan to install VMs with public IPs so that they can be directly accessed over the internet like in the following ...
1
vote
1answer
737 views

how to make bridge networking with KVM work in Fedora19

I'm attempting to get several virtual machines setup on a Fedora-19 host system, with the traditional bridge network devices (br0, br1, etc). I've done this many times before with older versions of ...
4
votes
1answer
305 views

New KVM guests cannot access outside LAN

I have a KVM host (at 192.168.0.10) that currently has one working KVM guest (at 192.168.0.12). On attempting to install a new KVM guest today, I reached a problem where the network on the new guest ...
0
votes
2answers
340 views

Why VM cannot get the public IP I have from provider?

I have a KVM-Host (on Debian) with root@kvm-host:/# cat /etc/network/interfaces auto eth0 iface eth0 inet manual auto vmbr0 iface vmbr0 inet static address 176.x.y.133 netmask 255.255.255.224 ...
2
votes
1answer
559 views

Why are eth0 and vmbr0 (bridge) having the same MAC addresses?

I configured my Debian (with KVM on board) as following: /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto vmbr0 iface vmbr0 inet static address ...
0
votes
1answer
304 views

How to configure a network on KVM using only public IPs?

I have a KVM server and two VMs. I have one main IP and two additional "single" IPs (not a subnet). I don't want have a local network with private addresses on my KVM, but I want to assign my public ...
0
votes
1answer
122 views

KVM firewall to disallow internet access for group of guests

I've got a KVM server inside a local network (192.168.10.0/24). This server has three interfaces, which are all publicly bridged [1]. Atm I'm only using two of the three interfaces, so the virtual ...
0
votes
1answer
188 views

KVM Physical NIC access

I'm new to KVM. I have a host with 4 NICs. I want to set this up, is it possible? eth0+eth1= bond0 -> internal network build two guests each guest will have network access to 2 subnets ONLY eth2 -> ...
1
vote
0answers
424 views

debian KVM - network bonding fails with vlan and bridge

i have a Debian 6 system configured with 2 NICs these NICs are used on a bond (bond0) which is used by bridge that require to use VLAN. i can get connection between guests running on VLAN10 but it ...
0
votes
0answers
102 views

how to carp two interfaces on same node?

I have this CentOS machine with 2 interfaces. eth0--> br0 (.10) eth1--> br1 (.11) Although part of the same network, each interface is being fed from a different switch. I use each bridge in ...
0
votes
1answer
140 views

KVM guest can't find gateway

I try to setup a KVM server with bridged networking. I followed the docs, but still can't get it working. The guest system can ping the host system and the host the guest system, so the connection ...
1
vote
1answer
156 views

Changing Linux Layer2 forwarding decision?

Are there tools to define in Linux something similar to Policy-based Routing, but on Layer2 level? Usual Linux bridge uses destination MAC to decide, which interface to send frame to. Can this ...
0
votes
1answer
122 views

KVM guest has a wrong outgoing ip address

I have a KVM host with a bridge configured on eth0 that has a public ip: auto br0 iface br0 inet static address xx.xx.aa.111 netmask 255.255.255.0 network xx.xx.aa.0 broadcast xx.xx.aa.255 ...
3
votes
1answer
406 views

Assign public and private IP addresses for a KVM guest

I would like to create a KVM guest with two different IPs, like one public IP and another private IP for the same KVM guest. My host is 210.x.x.x. Series and Guest are also configured with the ...
8
votes
2answers
2k views

Jumbo frames between KVM guest and host?

I am trying to implement a 9000 byte MTU for storage communication between KVM guests and the host system. The host has a bridge (br1) with a 9000 byte MTU: host# ip link show br1 8: br1: ...
1
vote
1answer
1k views

KVM is NOT seeing multiple bridges (only macvtap devices)

I am in the process of doing some thesis research about using ebtables and iptables on a KVM host to perform on-the-fly firewall restrictions to KVM guest VM's. Here is the problem: I have a bridge ...
0
votes
1answer
2k views

Use one NIC to create multiple interfaces for Linux KVM

I am working on a thesis research project, and I am having some difficulty figuring out how to make one NIC spawn several "bridge" interfaces such that each KVM VM can be seen on the local network. I ...
0
votes
1answer
443 views

KVM with external IP without NAT?

I have a CentOS 6.3 server with 1 NIC (eth0) and an external IP (lets say 1.2.3.4). On this server I'm running a CentOS 5.6 KVM with the "default settings" (virbr0 on 192.168.122.x). What I want to ...
1
vote
1answer
2k views

Centos/OVH: public IP on KVM virtual machine

Since a few days, I'm trying to configure my KVM vm to have a public IP address, without any success. First, I'm on OVH, and you need to know they don't allow networking from different mac addresses. ...
3
votes
2answers
2k views

Debian: Should I add vlan interface into bridge for KVM?

I am setting up a Debian Squeeze box as a KVM host. I want to add multiple interfaces to each KVM guest so I want them to be on different VLANs. After reading about this, I believe the best method is ...
0
votes
2answers
235 views

Ubuntu with KVM guest VM and broken bridges

I have an Ubuntu box with a KVM guest VM running. They use bridging so the guest VM attaches to the physical network of its host. The guest VM has 2 NICs in 2 different bridges. First NIC of the VM ...
0
votes
0answers
484 views

Two servers on the same network can't ping eachother

According to this guide I setup two servers. Now these two servers can't ping each other, this is arp -n result: # arp -n Address HWtype HWaddress Flags Mask ...
2
votes
1answer
971 views

IP Bridge for KVM with multiple subnets

I have a machine set up running KVM and a bridge on eth0 with the ip address for the machine. The machine has an IP address in a range with no more ip adresses free. I am trying to make a second ...
1
vote
1answer
170 views

Multiple IPs on eth0, bridging to VMs and routing

Current situation: I have a host running 3 virtual machines. One IP for eth0 (xxx.xxx.xxx.239) and one additional for eth0:1 (yyy.yyy.yyy.35). This works fine for me... Host (eth0) (xxx.xxx.xxx.239) ...
1
vote
2answers
4k views

How to bridge a range of public IPs to KVM virtual machines on Debian/Ubuntu

I've been trying for weeks to figure out the right network configurtion for sharing a range of public IPs with KVM virtual machines running on my server, but so far with little luck and with the help ...
1
vote
0answers
328 views

kvm bridge network not working

I have several KVMs and using public bridge mode. VMs can talk to each other but VMs can't access real network and the host can't reach VMs. One weird thing is that it used to work before and it ...
2
votes
2answers
3k views

KVM/Libvirt bridged/routed networking not working on newer guest kernels

I have a dedicated server running Debian 6, with Libvirt (0.9.11.3) and Qemu-KVM (qemu-kvm-1.0+dfsg-11, Debian). I am having a problem getting bridged/routed networking to work in KVM guests with ...
2
votes
1answer
702 views

NFS and KVM. Slow Speed

I have a KVM virtualization in Debian with 2 guests (Debian and Windows 2008). I want to have a 'mount point' shared that can be accessed by the 3 system (host and 2 guests) at the same time. So the ...
3
votes
1answer
973 views

Bridge and OpenVPN with shorewall

I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged ...
1
vote
3answers
2k views

Is there a way to determine which virtual interface belongs to a virtual machine in a kvm host?

I'm using qemu/kvm whith bridged networking. In the host machine there are several "vnetX" network interfaces without IP. I'm looking for a way to know which vnetX belong to a virtual machine. I ...
2
votes
3answers
1k views

KVM-Guests can't get past bridge - no internet connection

I'm running a backported KVM on a Debian Squeeze. ATM the KVM-Guest can't connect to the internet through the bridge I have set up. The guests can reach each other, the host but nothing outside. I can ...
4
votes
2answers
1k views

Creating a private network for two VMs

I am trying to create two VMs which are both connected to the same private network. I'm using Linux with qemu-kvm 1.0. My plan of attack has been this: brctl addbr bridge ifconfig bridge up tunctl ...