1
vote
2answers
203 views

routing back to LAN from RV082

We have an RV082 Linksys/Cisco router with a normal configuration of the WAN port connected to the internet, and the LAN port configured as 192.168.188.1. This might be a simple question, but I have ...
1
vote
1answer
294 views

Cisco SLM248G Switch Hardware Reset

We have two Cisco SLM248G switches within our environment. After some research, it seems that one is causing a few problems because during heavy loads, it is sending transmissions to our firewall ...
0
votes
1answer
2k views

Setting up QuickVPN clients with a Cisco small office router and getting a message indicating I must change the router's internal addressing scheme

I have a Cisco RV110W small office router (this configuration process is common to many Linksys/Cisco routers) and I am trying to define QuickVPN clients. When add a client of type "QuickVPN" the ...
0
votes
2answers
197 views

Bridging two networks

I'm hoping you may be able to offer some advice as I'm not very familiar with setting up routers/access points. I have a network of computers on an active directory domain on the 192.NET. I then have ...
0
votes
3answers
868 views

Does the Cisco SPA range of phones work with CallManager/CME?

I have about 15 phones and am looking to upgrade from asterisk to an all Cisco solution. Do we need to replace the phones as well?
2
votes
4answers
8k views

What serial cable do I need for a Cisco/Linksys SRW2024P?

Some idiot (one guess as to who) installed a Cisco/Linksys SRW2024P in a 2nd location and forgot to change the IP before doing so. Now it's on a new subnet and I need to control it via console port. ...
0
votes
1answer
735 views

Cisco LAP1142N-A-K9 wireless range similar to SOHO Linksys?

I've just started testing wireless for our building, we plan to implement it across the board this fiscal year. Currently we have no wireless except in our IT area (DSL for outside testing). I've ...
0
votes
1answer
725 views

What is the difference between Firmware v 1.3.7.2 and 4.0.0.07?

I got a RV042 (v1.2) and tried flashing 4.0.0.07; After some research I found out that the current firmware version is only flashable on v3 hardware. Does anybody know what the difference is/where ...
2
votes
4answers
872 views

Two cisco gigabit switches refuse to link to each other. Any idea why?

I have 3 Linksys SR2024 switches which are basically non-managed 24 port Gbit + 2 miniGBIC. I now had to add another switch to the network, and my provider didn't have the SR2024 switch anymore, so I ...
0
votes
2answers
824 views

Flashing Cisco SPA942 phone with SPA504G firmware

I have a Cisco SPA942 phone, which is no longer supported by Cisco. It's running the latest firmware available for this phone: 6.1.5(a). Cisco replaced the SPA942 with the SPA504G, which is almost ...
1
vote
2answers
796 views

open ports on a cisco/linksys wrt54g2 v1.5

Im upgradeing my router from a netgear fvs318 one of the problems im running into is on the old net gear i have opend ports under the "Add Service " for our voip udp 69 tcp 80 tcp 2000 udp ...
6
votes
2answers
2k views

pfSense Firewall or Linksys/Cisco router for small offices

I'm about to start switching some networks around for multiple small offices. Each office has about 10 to 15 users and 10 to 15 computers. Each office has a spread of generic routers and access ...
1
vote
2answers
6k views

What is the default username and password for the Cisco SPA-942?

I can't seem to find the default admin username and password for the web administration interface for the Linksys/Cisco SPA-942 VoIP phone. What is it?
0
votes
1answer
3k views

Why doesn't QuickVPN on the RV082 work anymore?

Anyone know why users who were able to access the VPN on a Linksys RV082 router via the QuickVPN client would no longer work? Below is a screen shot of the error message that users are receiving. ...
0
votes
1answer
836 views

Is it necessary to create a client to gateway VPN tunnel for QuickVPN users on the RV082?

Using the Linksys/Cisco RV082 router, is it necessary to create a Client to Gateway tunnel if all of the remote VPN users will be using Cisco's QuickVPN client, or can you simply configure the ...
1
vote
1answer
792 views

Upgrade firmware on a Linksys/Cisco RV082 from Mac OS X client

I'm trying to upgrade the firmware on a Linksys/Cisco RV082 router using Mac OS X and it's not working. The current firmware version is 1.1.6.14 (Jul 28 2005 18:12:59), and I've tried upgrading to ...
1
vote
2answers
1k views

What's the purpose of setting the static IP entries in a Linksys RV082 router?

I'm wanting to configure our Linksys RV082 wired router as our primary DHCP server and then have our Linksys WRT54G wireless router as a secondary DHCP server. My plan is to have them serve different ...
2
votes
2answers
1k views

Losing 1/3 of my download speed with my new router, any ideas on how to fix?

This is a cross post from superuser.com since no one over there seems to know anything. I recently replaced a dying D-Link router (DI-524) with a Cisco/Linksys RSV4000. I'm really happy with the ...
0
votes
4answers
3k views

What is a “Dead loop on virtual device” and how do I fix it?

I just recently got a new router from Cisco/Linksys which is the RVS4000. I keep getting messages in the log saying “Dead loop on virtual device sit1, fix it urgently!” but I’m not sure what it means ...