1
vote
0answers
28 views

How to change SAS address on Expander

I have the following setup - two supermicro backplane attached to one controller LSI SAS 9207-4i4e and unfortunately cannot access the disks, during boot there are disks only in one backplane, the ...
0
votes
1answer
49 views

How to perform disk test attached to LSI RAID controller

I have four Seagate ST33000657 SAS drives attached to LSi 9260-4i controller. I want to test them for hw errors and bad sectors, before launching into production. I ve tried SeaTools, but it's not ...
0
votes
2answers
434 views

No drives showing on LSI 2008 SAS + HP SAS Expander

Followin this guide http://www.servethehome.com/supermicro-x8si6-f-motherboard-review-including-onboard-lsi-sas-2008-controller/ I got myself an RPC 4224 case (They are called Inter-Tech in Europe, ...
2
votes
1answer
288 views

Does the Intel DX79TO motherboard support x8 devices (SAS HBAs) on PCIe x16 slots?

Context: I have an Intel DX79TO motherboard and a Sun SAS3081E-S/LSI 1060E-S HBA card with a PCIe x8 interface. I plug the HBA into my mobo next to my graphics card, and the HBA power lights ...
0
votes
1answer
506 views

Difference between LSI SAS3081E-R vs. LSI SAS3081E-S SAS/ATA HBAs

I'm trying to figure out if there are any differences between the "R" vs. the "S" of this SAS controller. As far as I can tell, the "S" is a Sun Microsystems re-branded version. I can't find much ...
7
votes
2answers
3k views

LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 ...
0
votes
2answers
508 views

MegaRAID SAS 8208XLP

I'm just wondering whether anyone knows if I can use a Debian distro with the MegaRAID SAS 8208XLP controller. Currently at the moment LSI only supply drivers/support for RHEL/CentOS but I was ...
1
vote
0answers
466 views

LSI 9211-8i won't boot in KVM

I'm running ubuntu 11.04 with an LSI 9211-8i in IT mode with the latest firmware (10). I'm using KVM with VT-d enabled to pass the entire PCIe device through to the guest OS. I have the device ...
0
votes
1answer
1k views

IBM System x3500 M3 refuses to boot from LSI SAS card if blank SATA drive is connected on mainboard

Have an IBM System x3500 M3 that refuses to boot from the IBM branded LSI SAS card if any SATA drive is also connected to the mainboard. The system restarts itself over and over. No error messages. ...
3
votes
1answer
202 views

Are PCIe v2 RAID controllers backward compatible with PCIe V1?

I am looking to add a PCIe V.2 RAID controller (LSI SAS 9280-4i4e) to an older Intel server (SR2500) which has PCIe V.1 slots. Does anyone have any experience with using RAID controllers designed for ...
0
votes
2answers
1k views

Is it possible to run LSI SAS 9211-8i PCI-E 8 in PCI-E 16 Slot?

I just bought an LSI SAS 9211-8i HBA(Host bus adapter) to use with my new hardware. I realized after looking at the card that it required an x8 slot and my new mobo only x16 available. I keep on ...