1
vote
1answer
79 views

LSI MegaRAID SAS 9261-8i: Disk isn't recognized after replacement

I've got a Supermicro Server with an LSI MegaRAID SAS 9261-8i Raid Controller inside. There were 3 Disks attached to the controller which were configured as RAID5 array. One of the disks failed ...
1
vote
0answers
46 views

running commands on physical drives on different backplane with megacli

So when I run "MegaCli64 -PDlist -aALL -NoLog | egrep 'Slot|state|Inquiry|Enclosure'" to grab a list of disks and their status. I can see a total of 36 disks. The issue is that they have the same slot ...
1
vote
0answers
34 views

I forget to record the physical disk sequence for MegaRAID before transfer. Is there any way to recover.

I was so careless when I send my server for repairing. I removed disks from chassis to protect the data, but I did not record the position sequence for each disk and my raid card failed to build RAID5 ...
2
votes
4answers
225 views

LSI RAID: Write cache policy affects read performance?

I have a server with a LSI MegaRAID SAS 9260-4i controller, RAID-5 with 3 x 2 TB disks. I did some performance testing (with iozone3) and the numbers show clearly that the write cache policy affects ...
0
votes
1answer
61 views

LSI Megaraid 150-6 as regular SATA controller

I have an old but reliable server board that does not have any SATA ports on it. Also i have LSI Megararaid 150-6 (with latest firmware) which i want to use as ordinary "dumb" SATA controller. I ...
0
votes
2answers
129 views

LSI Cachecade Pro 2.0 with RAID10 SSD Cache?

I'm trying to add a RAID10 SSD Cache to a VD by this command: [root@livecd storcli]# ./storcli64 /c0 add vd cachecade type=r10 drives=252:4,252:5,252:6,252:7 assignvds=0 Controller = 0 Status = ...
0
votes
0answers
642 views

Patrol Read Aborted on PD

Getting “Patrol Read Aborted on PD" warning message on MegaRAID Storage Manager. After research I found that Patrol Read and Consistency Check (CC) was scheduled by controller to run at the same time ...
0
votes
0answers
50 views

How to rebuilding RAID1 array on MegaRAID 9260-4i

I have running MegaRAID under Windows 2012R2, the original array has been setup with two 900GB SSDs. One SSD on Slot 1 failed and I replaced it with Seagate 2TB spindle but the controller instead of ...
0
votes
1answer
70 views

MegaCli: when did a drive fail?

Using MegaCli64, is there a way to find out when a hard disk failed? I.e., /opt/MegaRAID/MegaCli/MegaCli64 -ShowSummary -aALL shows Connector : Int.Ports ...
2
votes
1answer
342 views

Should I enable “Patrol Read” on SSD drives?

LSI, Intel and Dell RAID controllers (perhaps others) have a "Patrol Read" feature to try to spot when a drive is failing before it completely fails. LSI seems to disable patrol read on SSD by ...
2
votes
1answer
756 views

How to create Raid 10 with megacli

I have OpenFiler storage server. Without installing Windows and MSM, I want to create raid10 array from disks 2 to 21. I have already successfully installed MegaCli to OpenFiler but I'm stuck in ...
4
votes
2answers
183 views

megaraid: Logical Drives at different RAID levels

I am currently using a SuperMicro machine that has an on-board LSI 2208 controller (MegaRAID class). I want to create a single array from two drives and then carve that up into: one RAID1 100GB ...
0
votes
1answer
281 views

RAID: replacing a disk before it fails

We have a RAID 5 setup (Megaraid SAS ROMB) with 4 930 Gb physical disks running as a 2.7 TB VD. Recently (a few months back) we had a drive fail and had to leave it in degraded mode for ages (various ...
1
vote
1answer
2k views

Drive is failing but LSI MegaRAID controller does not detect it

smartmontools reports an increasing number of unreadable sectors on a drive that is used in a RAID1 configuration. I thought that the LSI MegaRAID controller also checks the SMART status of its disk ...
0
votes
1answer
56 views

How to find out the amount of sectors available in a RAID physical disk for replacement?

So, to start with, let me confess I have no knowledge of RAID besides what I read in a few APC mags 5 years back and what the acronym stands for. Everything I know now comes from assumptions and the ...
0
votes
0answers
207 views

Supermicro server with aftermarket MegaRaid

My company gave me a budget to build a VM server, so I bought a Supermicro server and saved some $$ by buying an aftermarket MegaRaid - 8308ELP (I know it's old, but it fit my needs and was cheap). I ...
1
vote
0answers
165 views

Possible bad raid card / hard disks (LSI 9261-8i)

I am in a bit of bad spot at the moment, i have a dedicated server hosted by someone else, it has a LSI 9261-8i raid card installed, attached is: 3x300GB SAS 15K rpm disks (in RAID5) 5x2TB SATA ...
0
votes
3answers
659 views

MegaRAID Storage Manager Error 1920 “Service MRMonitor (MegaMonitorSrv) failed to start.” on Windows Server 2003 R2 x64

I'm trying to install the MegaRAID Storage Manager 8.10 provided by SUPERMICRO, but I keep getting an error 1920 that "Service MRMonitor (MegaMonitorSrv) failed to start. Verify that you have ...
1
vote
0answers
157 views

Adding SSD boot disk to machine running RAID 10

I have a server (dev rig) that runs Windows 2008 R2 and boots from a RAID 10 setup. Now I want to add an SSD disk that will contain Windows 7 (could be dual boot, but dont plan on salvaging the ...
1
vote
2answers
208 views

Horrible performing RAID

I have a small GlusterFS Cluster with two storage servers providing a replicated volume. Each server has 2 SAS disks for the OS and logs and 22 SATA disks for the actual data striped together as a ...
2
votes
2answers
838 views

MegaRaid damaging disk by set a drive to “Offline”?

I wanted to test performance in a RAID10 with a "damaged drive". To simulate this situation I've set a single drive to "Offline" by using this command: MegaCli -PDOffline -PhysDrv [45:12] -aAll The ...
3
votes
1answer
717 views

Megaware Raid 10

I have 22 disks and would like to create a Raid 10. Unfortunately my raid controller (MegaRAID SAS 9260-8i) is only capable to handle 8 arrays within a RAID 10. Because of that I could only use 16 ...
7
votes
2answers
3k views

LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 ...
0
votes
2answers
508 views

MegaRAID SAS 8208XLP

I'm just wondering whether anyone knows if I can use a Debian distro with the MegaRAID SAS 8208XLP controller. Currently at the moment LSI only supply drivers/support for RHEL/CentOS but I was ...
0
votes
2answers
747 views

setup raid 6 with 12 - 2 TB drives

I have two 500GTB 7.2k Sata 2.5in drives, plus twelve 2TB drives, and LSI 9260-8i SAS/SATA Card. I need to have OS on one label the rest for storage. I am unsure how to build the raid6. It has the ...
1
vote
1answer
5k views

LSI MegaRaid warning: Patrol Read can't be started

We run a HyperV server on RAID-6 (the OS is Windows Server 2008 R2). The hardware is LSI MegaRaid SAS 8704EM2 controller, with 4x 1TB WesternDigital SATA drives. The server is up & running on this ...
1
vote
1answer
1k views

MegaCLI Media Error Count

This morning, I just got a Nagios alarm because of: BRUBLUst01:/usr/local/bin# /opt/MegaRAID/MegaCli/MegaCli64 -PDList -a0 Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Device Id: 0 Sequence ...
1
vote
5answers
1k views

MegaCLI always returns blank output

This server is a Dell R200 running Ubuntu 8.04LTS using a LSI SAS1068E raid card supplied from Dell, I suspect that there might be some kind of RAID issue with the hardware raid built into the ...
1
vote
1answer
1k views

Use MegaCli to reconstruct RAID on Dell PERC 5/i?

I have a RAID 1 + hot spare that I would like to reconstruct, online, into a RAID 5 set. I know this is possible with OpenManage, but I has anyone figured out how to pull this off using the MegaCli ...