The Network UPS Tools are a set of open-source programs that facilitate UPS monitoring in a networked environment using a client/server model.

learn more… | top users | synonyms

3
votes
0answers
80 views

Server not start in low battery (Network UPS Tools)

I have server (Centos 6.5 + nut-2.6.5 + Powercom BNT-600AP USB) everything works well, UPS picks up problems with electricity. When no electricity more than 10 minutes UPS shutdown the server, and ...
0
votes
0answers
195 views

Nut says APC UPS is on battery. It is not

Since 2 days my Smart-UPS 1500 RM reports it is on battery but this is clearly not the case since it's been running for more than two days indicating 100% battery with 01:30:00 running time. Batteries ...
1
vote
1answer
557 views

NUT UPS-Dummy driver in repeater mode for Synology NAS

I have a NUT client that requires the UPS it monitors to be named ups. The client (a Synology NAS) does not provide a method to change this configuration. My setup consists of multiple UPSes monitored ...
0
votes
1answer
875 views

install-man5 Error 1 after running 'make install' after compiling NUT (Network UPS Tools)

In an attempt to solve my NUT energy-saving problem that I've asked about in a lengthy serverfault question, I read that in the latest NUT version, nutdriver_qx replaces blazer_ser and I think it's ...
2
votes
1answer
2k views

How to disable UPS energy_saving with NUT?

I've got a Proline 650 UPS (Serial) installed Extra details: The UPS has a serial connection with a single 12v SLA battery. (It was not listed in the NUT compatibility list but after compiling NUT-...
0
votes
1answer
68 views

NUT UPS: stop specific service on power failure

Does anybody know how to stop a service when there is a power failure using NUT? I made a custom script like this, the problem is that the script user (NUT) does not have root permissions to stop the ...
0
votes
1answer
3k views

apcupsd vs NUT in Proxmox environment

I have a Proxmox node which is actually is HP Proliant DL 320e G8 server + APC SmartUPS 750 connected directly to the server by usb cable. On the host are running several Linux VMs. My question is - ...
-3
votes
1answer
3k views

Is a Virtualbox FreeNAS VM reliable (with a UPS)? [closed]

I started looking at - Is FreeNAS reliable? I would have taken issue with TV10's comment : "longer than a UPS would handle it" (but I don't yet have a rating high enough to do so). I am running a ...
4
votes
2answers
436 views

How to have NUT automatically power off a UPS before the monitoring system shuts down?

I've got NUT configured on a few systems in the following way: One host is connected to four UPSes via USB. That host is plugged into two of the four UPSes. Two other hosts are on the same rack, ...
0
votes
2answers
2k views

APC 2200 RM in a continual self-test! Why?

I've purchased two different used APC 2200 RM units, and both have entered into a mode where they execute a continual self-test: that is, they go on battery briefly, test, then the test comes back ...
1
vote
1answer
2k views

APC SC1000I over USB and NUT

I've got an APC SC1000I which I want to set up to be monitored with NUT, likely with newhidups. The basic config doesn't work: # tail -n 1 /var/log/messages Poll UPS [apc@localhost] failed - Driver ...
0
votes
3answers
2k views

FreeNAS NUT Slave and not master?

I have 2x FreeNAS servers and one UPS. The First FreeNAS server has the NUT stuff configured, running and working just fine. Is there a way to configure my second freeNAS server to be a slave to the ...