The tag has no usage guidance.

learn more… | top users | synonyms

5
votes
1answer
583 views

IPSec + L2TP + NAT-Traversal does not work for multiple clients behind same nat

I have recently configured a VPN server hosted in AWS EC2. Details: Centos 6.4, openswan, xl2tpd, NAT-traversal. The configuration works great for a scenario when only one user connects form a given ...
3
votes
1answer
355 views

VPN ERROR 500 STATE_MAIN_I1, unable to start phase2

i'm trying to set up a site to site vpn to a fortigate 60c from a CentOS 7 with openswan, the error i get everytime is the following 000 #1: "office":500 STATE_MAIN_I1 (sent MI1, expecting MR1); ...
4
votes
0answers
852 views

How do I configure OpenSwan to allow pure IPsec (not L2TP) connections from an iPhone?

Similar to this question, I want to configure an IPsec server on Linux which will accept connections from the iPhone. However, unlike the other question, I want to be able to test with pre-shared keys ...
2
votes
0answers
77 views

Is there an extension of host to host ipsec to a many-many configuration?

Having a typical host to host transport mode ipsec configuration, conn appserver01-to-swift01 leftid=@appserver01.server.com left=10.133.176.246 leftrsasigkey=xxxxxxxxxxxxxxxxxxxxxxxx ...
2
votes
0answers
801 views

Creating redundant IPSec connections using OpenSwan

I have a linux (netkey) instance with openswan installed, the instance has two connection to the same IPSec peer that needs to act as redundant connections. both connections' properties are the same ...
2
votes
0answers
159 views

Openswan bad routing record after connect

I have a problem in openswan configuration. In the routing table create following lines on the client, after connect to server: Dest mask Gateway Conn Metric 0.0.0.0 ...
2
votes
0answers
582 views

OpenSwan + AWS + Ubuntu 14.04 - Cannot reach server

i'm currently trying to set up a VPN in order to login into a private subnet hosted on AWS. The target host has Ubuntu 14.04 and installed OpenSwan. I've setup ipsec.conf, ipsec.secrets, xl2tpd.conf, ...
2
votes
0answers
4k views

ipsec IKE phase 1 failure

I have a wireless gateway that supports site-to-site IPSec. I have configured openswan on Ubuntu Server 12.04 (left side of the tunnel) with the following /etc/ipsec.conf: version 2.0 config setup ...
2
votes
0answers
220 views

Sending L2tp/IPsec PSK client packets to OpenSwan server

I'm trying (kind of) to create VPN client, I set my server on Ubuntu using OpenSwan (L2tp/IPsec PSK). What I'm doing right now is sending packets to my server and trying to exchange my keys with the ...
1
vote
0answers
57 views

Openswan IPSec VPN on AWS tunnel established but no traffic

I am setting up a tunnel with a telco using AWS/VPC/EC2/Centos7/Libreswan and have been stuck for weeks. Appreciate any help! I have 192.168.16.73 (VPN GW, EIP 52.76.x.x) and 192.168.16.116 ...
1
vote
0answers
229 views

Openswan through Amazon VPC Routing to Office Network

Were trying to create a road warrior VPN network. Since the internet in our office is slow, we are running it through a VPC with a replicated AD and File Server. There is currently an Amazon VPC VPN ...
1
vote
0answers
157 views

openswan IPSEC site to site randomly disconnects on debian server

goodmorning my friends, this is my situation: I have two debian servers with static IP connected through a site to site VPN OPENSWAN, everything works like a charm, I can ping the entire lan from any ...
1
vote
0answers
227 views

amazon ec2 instance going to a remote ip using openswan tunnel is up but no traffic being established on the remote ip

I having establishing a vpn tunnel to a remote peer/public ip using amazon ec2 openswan. The tunnel is up but no traffic has been seen on our side or the remote side? Is there I been missing? Please ...
1
vote
0answers
179 views

Openswan and Cisco ASA

i have post this same question on "Unix & Linux" but iv got no answer and will delete from there but ill try here too. I need this as soon as possible to solve it or at least to find out what is ...
1
vote
0answers
300 views

Openswan ip tunnel not passing traffic

I had this tunnel already working, but now I needed to add two more ips 10.50.240.48/28 and 10.50.96.0/20. I set up my left and right and leftsubnets and rightsubnets properly in the openswan config. ...
1
vote
0answers
2k views

Cannot connect to IPSEC/L2TP VPN Arch Linux/Windows 8

I have check a lot of other L2TP/IPsec VPN post and none of them seem to quite match the issues I am having so here is what going on. I am trying to set up a VPN on my Arch Linux server that I can ...
1
vote
0answers
272 views

Openswan and sonicwall and encryption parameters

This error leads me to investigate my encryption parameters: 003 "sonicwall" #2: ignoring unknown Vendor ID payload [...] Can some expert please have a look at tell me what is wrong? Sonic wall ...
1
vote
0answers
571 views

Is it possible to do IPSec Site to Site VPN without static & public IP on one end?

I am working on a project for my engineering degree that requires me to interface with some pre-existing equipment, so I am rather limited on my options. I'm rather new to VPN and ipsec for that ...
1
vote
0answers
248 views

IPsec connection established but xl2tpd times out

This may or may not be related to my problem with passing ipsec verify. I have configured L2TP/IPsec VPN on Ubuntu 13.04 following Ubuntu's community documentation and while IPsec connection seems ...
1
vote
0answers
714 views

L2TP & IPSec (OpenSwan) on Centos time out when connecting

I'm having big trouble setting up a very simple VPN. Using Centos 6. My Server Address : 61.34.26.32 (fictive) Whenever I try to connect (from iPhone5 or MacOS X) i get a connection timeout. I ...
1
vote
0answers
299 views

Trouble connecting my server to a firefwall trough VPN

I have a server running Ubuntu and Openswan, but I'm not able to connect to the remote firewall. I hope that anybody can help me. My ipsec.conf-file is as follows: config setup protostack=netkey ...
0
votes
0answers
19 views

Routing Outbound Traffic through IPSEC Tunnel

I've been trying my hardest to figure this out for the past week, and think I have a general idea of what's going on, but can't figure out how to solve it. We have an OpenSwan server in an AWS VPC ...
0
votes
0answers
13 views

OpenSwan on Amazon EC2 - max number of retransmissions reached STATE_MAIN_I3. Possible authentication failure:

We are communicating with one of our clients over a VPN Tunnel. Openswan tunnel was working perfectly fine before. Today we attached an Elastic IP to the server and rebooted. Since then the tunnel ...
0
votes
0answers
6 views

IPsec Tunnel Deterministic Delay

I setup a site-to-site IPSec tunnel using OpensWan. I notice a constant delay of 15sec before the firewall gives back the response to the application running on a host behind it. 17:50:41.638828 IP ...
0
votes
0answers
35 views

Why I have 2 tunnels up on Openswan?

I have started to use Openswan on Centos6 and was able to configure Host to Host using the following document: ...
0
votes
0answers
18 views

Why ping stop to work when I stop ipsec service?

I have started to use Openswan on Centos6 and was able to configure Host to Host using the following document: ...
0
votes
0answers
21 views

Openswan and nat_traversal

I got a problem with openswan and nat_traversal option. If it is set to no, my tunnel goes up but i cannot exchange packets with the peers because i'm behind a router. If it is set to yes, a lot of ...
0
votes
0answers
203 views

One Way IPSEC VPN Traffic (Centos/Ubuntu to pfSense)

I have servers sitting at Digital Ocean and I need one of them to be able to get into my internal network and pull information via SNMP. The particulars: (server)--DO Private Net--(vpn-2 ...
0
votes
0answers
37 views

Hyper-V and Openswan

I have Openswan on Hyper-V and I have notice that for every tunnel I have there is no route. So the tunnels are established, local pc can ping each other. With "ip xfrm policy" the policy are shown, ...
0
votes
0answers
344 views

IPSec Tunnel AWS VPC <-> openSwan CentOS 6.6 Tunnel up, no traffic

EDIT: Allow ESP traffic through firewall. This resolved the issue. I managed to get a tunnel up between a CentOS 6.6 box and our AWS VPC. It shows as connected on the box, and in AWS, but the ...
0
votes
0answers
70 views

OpenSwan IPSec tunnel not routing correctly

I am trying to enable site-to-site connectivity between my network and a Windows Azure network. I have configured openswan in the local network and service ipsec status reports that the tunnel is up ...
0
votes
0answers
48 views

Openswan : Traffic not passing through tunnel

PLEASE HELP : whenever I ping one of the other site servers , the connection does not go through the other site public ip. the setup is as follows : Public gw ip of other site : 6.6.6.6 Server that ...
0
votes
0answers
43 views

Openswan VPN routing issue

I have configured the openswan VPN correctly on an EC2 server ( Elastic IP ), and it shows 2 tunnels up. Given the following setup : MY_PUBLIC_IP: x.x.x.193, MY_ENCRYPTION_DOMAIN: ...
0
votes
0answers
217 views

Ubuntu 14.04 Cant connect to openswan/xl2tpd/IPsec VPN via iOS

I am setting up a VPN using openswan, xl2tpd, and IPsec and i am getting issues with connecting via an iOS device with the error "You were disconnected by the communication device". This is configured ...
0
votes
0answers
295 views

Windows Phone 8.1 client unable to connect to Ubuntu VPN server (L2TP with IPsec)

I have set up an L2TP + IPsec VPN server on my Ubuntu server (14.04.2 64bit) using openswan. I got it working with Android and Windows 8.1 clients, though Windows 8.1 required some tweaking. When ...
0
votes
0answers
856 views

Site-to site Configuration between OpenSwan and Cisco ASA

I am making site-to-site vpn connection using amazon ec2 linux and cisco asa router ( please note i donot have access to router only configuration is provided.) CISCO ASA CONFIGURATION : ...
0
votes
0answers
106 views

openswan initiating from wrong IP, but answers with the right one

I'm running a Debian 7.8 openswan 1:2.6.37-3+deb7u1 server with one external interface, but many different aliases : inet xxx.xxx.xxx.94/24 brd xxx.xxx.xxx.255 scope global eth1 inet ...
0
votes
0answers
835 views

subnet-to-subnet libreswan ipsec vpn

I'm configuring a "subnet to subnet VPN" between two Centos 7 server using libreswan. Each server has two nic as showed in the following image. I would allow secure communication between the subnets ...
0
votes
0answers
86 views

Site to Site VPN tunnel to private network

I'm looking for a little help with a network setup. I have a router which I will be using for routing network, this will be 10.0.100.1 and it will be connected to the internet with a public static ...
0
votes
0answers
206 views

iptables DNAT packets into an openswan IPSEC tunnel

I have the following network setup: +-----------------------------------+ | | ...
0
votes
0answers
485 views

Configuring OpenSwan for IKEv2 (via iOS8)

I'm trying to configure OpenSwan (running on Ubuntu) to accept connections from an iOS8 device. I receive the following logs, which seems to indicate the server denies IKEv2 connections (even though ...
0
votes
0answers
177 views

IPSec tunnel between Cisco and openswan

We need to setup a site to site vpn connection and Our provider use Cisco system and we are planing to use openswan on centos (hosted on digitalocean). Our provider asking us following information. ...
0
votes
0answers
352 views

Openswan malfunction since update

For security reasons i performed and update from a previous version of openswan to U2.6.32/K2.6.18-194.el5 (netkey) Since that moment i've been experiencing constant tunnel drops, i've checked the ...
0
votes
0answers
538 views

OpenSwan IPsec connection drops after 30 seconds

I'm trying to connect from my Linux Mint 16 box to a CloudStack server through IPsec L2TP. Building up the connection works (pings work across the tunnel). However 30 seconds later the IPsec tunnel ...
0
votes
0answers
859 views

Multiple Windows clients behind a same NAT gateway cannot connect to L2TP/IPsec VPN server at the same time

I have set up a L2TP/IPsec VPN server on a cloud VM (with a public IP address) running CentOS 6.5 (kernel: 2.6.32) with openswan/xl2tpd (openswan: 2.6.37, xl2tpd: 1.3.6). However, if multiple Windows ...
0
votes
0answers
479 views

Debugging IPSEC log

A Fortigate unit and a Openswan based Linux server. Tunnel is up but no data goes through. This is the log from the Forti unit: Line 204: ike 0:Brazil_VPN:2803378:19809969: responder received first ...
0
votes
0answers
70 views

Iptables being changed without rebooting

I configured a tunnel between my network and a remote network with OpenSwan. On my tunnel endpoint, running on Ubuntu, I added iptables rules to disable source NAT (SNAT) when the destination was the ...
0
votes
0answers
786 views

l2tp vpn is disconnected after few minutes

I installed IPSec/L2TP on my vps server. I tried to connect from my mac to this VPN server. First time, connection is succeeded. But after a few minutes, connection was broken by itself. After ...
0
votes
0answers
78 views

VPN Server Doesn't Allow Internet Access

I recently set up a VPN on my local network to test and confirm that I could do it before sending it to my production server on Amazon AWS. It worked perfectly well, and I was satisfied with the ...
0
votes
0answers
110 views

OpenSwan issuing same IP

So I have finally got the authentication to work, and it will now connect, but when I go to use the connection I can't actually use the network. looking at the connections it seems to be issuing the ...