1
vote
1answer
57 views

Private VLANs/Port Isolation on HP ProCurve 2524

I am trying to set up Private VLANs (as described on Wikipedia) on a HP ProCurve 2524, but I can't find any references to it in the online manual. Searching the internet hasn't yielded much either ...
3
votes
3answers
574 views

What do switches do to tagged and untagged VLAN packets?

Let's say we have a 4-port switch that is VLAN capable. 1 2 3 4 Port 1 is TAGGED to VLAN10` and `UNTAGGED to Default_VLAN(1) Port 2 is UNTAGGED to VLAN10 Port 3 is UNTAGGED to ...
1
vote
1answer
222 views

HP Procurve 2610 vlan routing

Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all ...
2
votes
2answers
571 views

VLAN Traffic changing source when captured at firewall

1) HP Switch config below 2) Fortinet Policy in attached image Right now, we are a flat network of roughly 320 wireless devices, and about 100 wired devices. We have a FortiGate 300C firewall with a ...
0
votes
0answers
95 views

Is it possible to set up a management VLAN on HP switches without configuring routes on the WAN routers?

The network I help manage/maintain is configured like so: Location A - 10.0.0.0/22<br /> Location B - 10.0.4.0/22<br /> Location C - 10.0.8.0/22<br /> etc. Our ISP owns and ...
1
vote
1answer
214 views

Default Gateway in a VLAN

Could I have a router/firewall device providing WAN connectivity, part of a VLAN on a switch? For example: 2, L3 Switches. 2 VLANs DefaultVLAN 10.1.1.0/24 VLAN100 192.168.1.0/24 Two ...
1
vote
1answer
344 views

VLAN Gateways and Routing

This for hypothetical purposes - more of a learning question than an production question. If I have switch (Layer 3, lets say a Procurve) with a handful of VLAN's configured. Lets say: DEFAULT VLAN ...
0
votes
1answer
424 views

Getting invalid input error on procurve 2510 when setting up ip helper-address

I have 3 HP Procurve 2510G-48 and I want to setup a VLAN for public wifi (VLAN100). Originally I just had the default vlan1. I have computers communicating across switches on VLAN100 with static IP ...
5
votes
1answer
748 views

Procurve Primary VLAN

I'm trying to depreciate usage of VLAN 1 on my ProCurve switches; 1 is unused. I understand that VLAN 1 must exist, but I want to remove it from all ports, especially trunks between switches. The ...
1
vote
0answers
171 views

How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

As you can see from my question, I have a VLAN configuration problem with a ProCurve 3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I ...
0
votes
3answers
523 views

Multiple VLAN on one switch port

I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the ...
1
vote
0answers
82 views

Datacenter redundant hosting setup advice

We are moving our servers to a new DC and I am looking for a bit of advice with our new COLO setup. I have some knowledge of networking but I am an enthusiast more than anything so it gets a bit ...
1
vote
1answer
272 views

Procurve VLAN configuration

I have two ProCurve 1800-24G J9028B linked toghether by a fiber channel on ports n.23. I want an ethernet port (ex. port 21 of switch n1) to be isolated from all the others except of one of the other ...
1
vote
0answers
2k views

HP Procurve 2910AL allow traffic from VLAN to VLAN

We are trying to setup so that the switch handel routing and communication between a few vlans. And then have a link network up to the fw. Here is the config: Running configuration: ; J9145A ...
2
votes
1answer
734 views

Setup VLAN agnostic ports on HP ProCurve 1810G (Ingress Filter, Trunking)

I am wondering if it is possible to configure some ports of the web managed ProCurve Switch 1810G to participate in all VLAN traffic. Even if no VLAN with that ID has been set up inside the switch. ...
0
votes
1answer
372 views

Tagged VLAN with Procurve switch and RHEL is not working as expected

I want to configure tagged VLAN on RHEL6 where the ethernet switch involved is a ProCurve one. Now what I did is: I created VLAN interfaces eth0.1001 and eth0.1002 on RHEL6 for server1 and VLAN ...
5
votes
2answers
915 views

Multiple vlan issue with procurve switch

I have a cisco asa5505 as my rtr/fw(10.1.3.254). I have vlan 1 and vlan 3. Vlan 1 is my default all access vlan. Vlan 3 is my Guest(dmz) vlan. I can't seem to get a dhcp ip address when my laptop ...
2
votes
2answers
3k views

VLAN security on HP ProCurve 1810G-24?

I'm looking into the managed switch HP ProCurve 1810G-24 to see if it can meet our office demands. The specs say it has IEEE802.1Q - whatever that means. Our office consists of four companies that ...
-2
votes
2answers
1k views

VLAN routing issue

I have HP Procurve Switch 2910AL-24G. Please see attached configuration. Client inst2is01 (10.247.167.80) and VLAN ID is 37 Server ILO (Management Port) IP : 10.247.172.70 and VLAn ID is 54 From ...
3
votes
1answer
794 views

vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that ...
8
votes
3answers
2k views

HP Procurve Issue Passing Multiple VLANs over a link

Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2610 switch. This switch is then ...
2
votes
2answers
484 views

Adding second HP 2410G-24 Switch

We have a single HP Procurve 2410G-24 Switch. For the sake of simplicity, there are 2 VLANS configured, and the ports are roughly equally split between them. VLAN1 (LAN) is for server LAN ...
1
vote
0answers
397 views

HP ProCurve & Cisco switches interoperability

I have a couple of questions regarding Cisco and HP ProCurve interoperability. Here's a link to pdf with my network topology. Can someone help me with basic VLAN configuration in such topology? Below ...
2
votes
1answer
172 views

Wifi hosts can't contact one another (but wired hosts on the same vlan can)

Our current network is vlan'd, and the wifi network is on its own separate vlan (130). To connect to the 130 vlan, you connect to the access point (a HP MSM310), which is connected to an HP Procurve ...
7
votes
1answer
2k views

How to configure a HP Procurve network for IPv4+IPv6

The setup: We are an apartment complex with approximately 1700 units. Every apartment has internet with an ethernet plug in each. The network has 60 HP 2910al-48G switches connected to a central HP ...
3
votes
1answer
4k views

Procurve 2810 command line - reassigning ports to a different VLAN

A very basic question, but my googling has failed to find an answer... At present the VLAN config looks like this: vlan 1 name "DEFAULT_VLAN" untagged 1 ip address 10.200.1.134 ...
1
vote
3answers
3k views

Cisco Catalyst VTP to HP ProCurve GARP?

I have two L3 capable ProCurve switches (2810-24G) which I would like to use in our Cisco environment. The Cisco switcheshave vtp configured, and all VLANs are added/maintained basically on the ...
0
votes
1answer
413 views

Procurve Switch Multiple Gateways

I have a Procurve 3500yl switch that is currently handling all of the VLANs and the default gateway for my network. Currently, the gateway is set to our old FreeBSD firewall/router and I am trying to ...
2
votes
1answer
10k views

Configuring VLAN's on two HP procurve switches

Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects ...