Hewlett Packard's range of Intel and AMD-based free-standing, rackmount and blade servers.

learn more… | top users | synonyms

-3
votes
2answers
1k views

HP ProLiant DL380e Gen8 has high fan speed after installing second CPU

Today I installed a second CPU in our HP ProLiant DL380e Gen8, and after booting the fans all went to 99.96%. This causes the server to make an enormous amount of noise. Could it damage the server? ...
0
votes
1answer
133 views

Continuous I/O latency error on ESXi 5.0

Recently I posted a question on HP Proliant DL180 G6 - Smart Array P410, bay 11 error which the answers helped me to dig through. And today that I just noticed under my vSphere log which gives a ...
1
vote
1answer
629 views

HP SSD on ProLiant DL360p Gen8 p420i controller - no TRIM?

We have a HP Proliant Dl360 Gen8 server with the 420i 2Gg disk controller. (646905-421) we have a couple of the HP Gen8 200GB 6G SAS SLC SSDs (653078-B21), (they run in RAID1) We run Debian6 on this ...
1
vote
1answer
185 views

HP ProLiant DL360p Gen8 how to choose correct heatsink? [closed]

We purchased a new HP Proliant DL360 gen8 server (670640-425) (HP DL360p Gen8 E5-2620 Base EU) at the same time we purchased the cpu/heat-sink package for a 2nd CPU (654782-B21) (HP DL360p Gen8 ...
3
votes
3answers
679 views

Available Memory Slots DL380G5

I have an HP ProLiant DL380 Generation 5 in a remote data center. Is there any way that I can check remotely how many memory slots are occupied (and more importantly how many are available)? The ...
-2
votes
1answer
98 views

Difference of HP network adapter types?

HP have a special type of cards they call FlexibleLOM, and I can't figure out what the differences are of the following HP Ethernet 10Gb 2-port 530FLR-SFP+ Adapter HP Ethernet 10Gb 2-port ...
3
votes
2answers
557 views

How can I monitor HP P410 hardware RAID degraded in Freenas

I would like to run freenas on a HP P410 hardware RAID 5 4x600GB 15k SAS array and be alerted in the case of physical disk failure, however the freenas documentation says: to prevent problems, do ...
4
votes
1answer
420 views

HP ProLiant Gen8 Health Agents and EL6.x - cpqHoMibHealthStatusArray has changed to the value: x

I've noticed that my HP ProLiant Gen8 servers report the following message via email to root (or the destination configured in /opt/hp/hp-snmp-agents/cma.conf) upon restart. Trap-ID=11020 ...
6
votes
1answer
223 views

Is it possible to enable RAID 1 on an already in-use HP Proliant DL380 G5

I have a HP Proliant DL380 G5 with two HDDs in RAID 0 (Stripe)(72GB+72GB). It has been running Windows Server for quite a while now and has 30GB of occupied space on a stripted volume. I've now ...
1
vote
1answer
478 views

HP Proliant ML350 G6 Smart Error Test

I have a ML350 G6 with two array controllers : P410 and P410i. I have updated all possibile firmware on this server. I have 5 x Seagate Savvio 10K SAS drives. I am testing the drives with HP Insight ...
2
votes
1answer
378 views

HP ProLiant with SATA/SAS Drives

I Currently have a DL350 G5. I have 4 74GB SAS drives in RAID that work fine but I tried to add a 1TB WD RED SATA drive for some storage and the RAID controlling isn't giving me an option to create a ...
3
votes
4answers
1k views

HP Proliant DL180 G6 - Smart Array P410, bay 11 error

I've been trying to search over ther internet for a solution to fix this. I'm the new IT person for my organization and our previous IT have not kept any records on certain things. I do understand, ...
2
votes
2answers
764 views

HP ProLiant server - multiple raid controllers?

We just got a brand new HP DL370 G6 server with 14 X 146 gb and 2 X 300 gb sas drives. Inside we got 3 raid controllers (one HP DL370, one HP P410 and one HP P812). It has 2 disk bays and each of them ...
4
votes
1answer
2k views

Updating firmware on HP ProLiant DL380 Gen8 failed

I tried updating the firmware on my HP ProLiant 380e Gen8, but I received this error: What could be the reason? Could it be because of limited disk space in the /tmp directory? ~ # df -h ...
1
vote
2answers
494 views

HP Smart Array P822 w. Dual D2700 - cabling for best performance

Reading the D2600/D2700 User guide, there's a section called "Cabling examples", but none of the examples match what we intend to do. I just want to make sure that it makes sense, before we do it. ...
26
votes
2answers
816 views

HP plan to restrict access to ProLiant server firmware - consequences?

I've been a longtime advocate for HP ProLiant servers in my system environments. The platform has been the basis of my infrastructure designs across several industries for the past 12 years. The ...
-1
votes
1answer
288 views

hp proliant dl380 g5 won't power up [closed]

Sorry for a probably silly question. I just bought an used hp proliant dl380 g5. It is supposed to be in a ready to use state. The problem is that it does not power up. The power green lights at the ...
2
votes
2answers
963 views

vSphere ESXi - Use both HP ProLiant DL360 G7 and DL360p Gen8 in the same cluster

I have vSphere cluster with few HP DL360 G7 servers, with Intel X5675 processor. I want to buy new server, HP 360 Gen8 with E5-2600 processors. Can I have this 2 kinds of servers in the same ...
0
votes
0answers
182 views

I am seeing error during boot sequence on HP ProLiant ML350p Gen8

The error states: Caution: Memory conflict detected. You may face boot problem. What steps would you recommend I take to troubleshoot this? Details: Dual Xeon E5 v1, two LSI 9286-8e ...
1
vote
1answer
451 views

logical drives on HP Smart Array P800 not recognized after rebooting

We had a Smart Array P800 configuration working fine (RAID5). Physically, we have a disk enclosure (like this) connected with a Linux Server. Here is what happened: This server was accidentally ...
1
vote
1answer
1k views

HP P410i Array Controller and lost logical Drive

Today earlier we lost the logical drive information for a 4 drive raid array that was array B! The system had two arrays A and B A being the single system drive and B the Data drive of 4 x 136Gb ...
2
votes
1answer
98 views

Installing DIMM modules in HP ProLiant DL180G6 not in recommended order

I have two DL180G6 servers, I used them with 2x2 GB RAM modules, now I'd like to upgrade the memory to 16 GB for each. I have spare 6x2 GB RAM modules per machine (parameters match for the existing ...
-1
votes
2answers
877 views

Poor SQL performance on HP ProLiant ML310e Gen8 v2 with raid10

I recently bought HP ProLiant ML310e Gen8 v2 server with 8G's RAM and 4 HP 1TB 6G 7.2k rpm SATA (3.5in) Non-Hot Plug MDL HDD disks. It was surprise to me that HP didn't provide debian drivers for ...
3
votes
1answer
2k views

CentOS 6.5 with HP ProLiant DL360e Gen8

I have a chance to install a new HP ProLiant DL360e Gen8 server. There are three hard drives. How do I configure RAID 1 on this type of server. Will RAID already be configured so that it will look ...
1
vote
3answers
1k views

HDD with HP Proliant ML310e

I recently purchased a HP Proliant ML310e off PCNation.com as it seemed like a great deal. Come to find out, when I go to open up the case and install HDDs, the system is equiped with a ...
3
votes
3answers
832 views

VMware ESXi 5 on HP ProLiant DL320 G5

Can someone confirm that ESXi5 v.5.1 works on a HP ProLiant DL320 G5. VMWare compatibility matrix shows DL320 G6. If it works, do you use any specific drivers ?
2
votes
1answer
224 views

HP DL380G6: Where is the Temp. Sensor #29 (System Zone)?

The Temp. Sensor #29 of my HP DL380G6 seems to give me a wrong number. It says that the temperature is more than 50C (Caution: 60C, Critical: 65C) while the actual value is 13C. And I think it may be ...
3
votes
1answer
82 views

Network card location

I am generally familiar with hpacucli and hpasmcli but how do I determine in which slot a network card is installed? I need to be able to map to and from the slot and the MAC (and from there to the ...
6
votes
2answers
5k views

Disk/RAID Monitoring for HP Proliant Servers and Ubuntu 12.04

How can I monitor the status of the hard disks and the RAIDs of an HP Proliant server using Ubuntu 12.04. In Ubuntu 10.04 I could use the cciss-vol-status to query the RAID status periodically but ...
3
votes
1answer
124 views

RAID 5 drive upgrade

We have an HP ProLiant ML350 G5 server with an 8-bay RAID 5 array configured on a Smart Array E200i controller. The system volume and data are on the same logical drive. The drives are 72GB each and ...
-1
votes
1answer
162 views

HP ProLiant - Does ILO 2 Advanced offer additional SNMP or IPMI features?

We've got ML350 G5 servers with iLO 2 standard license. Does upgrading to higher iLO license will unlock new SNMP or IPMI data registers? If it will, which ones?
3
votes
2answers
136 views

Switch disks between array controllers

I have an HP ProLiant ML 350 G5, which has an HP Smart Array E200i/128 BBWC Controller embedded. This controller manages two arrays (each with three 72 GB disks in RAID 5) This controller has ...
4
votes
2answers
2k views

HP ProLiant DL360 G6 reporting missing fan

I have several refurbished HP ProLiant DL360 G6 servers and several of the systems are reporting fan failures - possibly incorrectly - on fan #2. When running: hpasmcli -s 'SHOW FANS' I get the ...
2
votes
0answers
197 views

HP SNMP Traps signalled every 10 seconds for a NIC

I'm trying to setup SNMP traps on my HP DL160 G6 (Xenserver) to notify me whenever I have issues with the server. Following suggestions from this serverfault post, I've installed the HP SNMP agents ...
-5
votes
2answers
101 views

Drive fault was asserted DELL [closed]

i have a DELL PowerEdge 2950 Server whit raid for 3 HDD. A friend whit a HP Proliant server which has broken, come to my help, to save information from the hard drive only had. When i put on my server ...
3
votes
2answers
1k views

HP DL320e Gen8, 3TB drives, Windows Server 2012 R2 - HDD full capacity alocation difficulties during installation

One interesting task to do but not so easy as i thought. The server is HP DL320e gen8, The main difficulty is with partitioning the RAID1 (2x3TB HDDs) during the installation on 2 partitions (System ...
5
votes
1answer
2k views

Identify HP Array Logical Drive From Windows

Probably something simple, but I'm trying to identify which logical drive in my HP Server's Array relates to a particular disk presented in Windows Server 2003. So I have a Proliant DL580 G5 server ...
1
vote
2answers
3k views

HP DL380e Linux not seeing drive array for installation

I am trying to install Linux and FreeBSD on a HP DL380e. However, during the installation process all of the OS's are stating that they can't find any disks to install to. Even RHEL. If I try to use ...
0
votes
2answers
723 views

“HP Insight Management WBEM Providers” download

I am trying to query a Proliant Server's health thru Powershell. But I can't find a place to download the HP Insight Management WBEM Providers from here. Is there any other Powershell equivalent of ...
32
votes
2answers
7k views

HP ProLiant DL360 G7 hangs at “Power and Thermal Calibration” screen

I have a new HP ProLiant DL360 G7 system that is exhibiting a difficult-to-reproduce issue. The server randomly hangs at the "Power and Thermal Calibration in Progress..." screen during the POST ...
0
votes
0answers
177 views

hp-health install doesn't work on Debian 7 (Wheezy)

I try to install hp-health on my HP ProLiant ML350 G4 server with a Debian 7 (Wheezy) installation. I downloaded the package on : ...
3
votes
2answers
14k views

Can't enter HP SmartArray P410 RAID ORCA set-up on HP ProLiant DL320G6

I've just installed an HP SmartArray P410 controller into my HP ProLiant DL320G6 server. The controller seems detected by the server BIOS (it shows up in controllers list in the BIOS set-up), hard ...
1
vote
1answer
67 views

Sideband on HP ILO2 and initial in-OS setup possible?

Is it possible to configure sideband (ILO being physically accessed from one of the main NICs as opposed to the dedicated ILO NIC) for the ILO2? Also is it possible to configure the ILO2 initially ...
1
vote
1answer
1k views

HP DL360 G7 P410i controller troubleshooting

Server is HP DL360 G7 with P410i disk controller. 2xE5620 CPU's. 16GB RAM. Linux mysql 2.6.32-5-amd64 #1 SMP Mon Feb 25 00:26:11 UTC 2013 x86_64 GNU/Linux (Debian 6.0.7) hpacucli "ctrl all show ...
2
votes
1answer
1k views

HP ILO utility for Ubuntu - hponcfg fails due to missing hp-ilo package

I'm working with an Ubuntu-based system running on an HP ProLiant DL360p Gen8 server. I prefer to install HP's management agents when I can for full hardware monitoring/configuration capabilities. ...
0
votes
1answer
306 views

How to set up direct access storage between a BL460c Gen8 (Win Server 2012) and D2220sb storage blade

I have installed a D2220sb storage blade in a c3000 enclosure. The storage blade's partner device is a HP BL460c Gen 8 Server. How do I setup a direct access storage? I have googled and tried to ...
7
votes
6answers
16k views

SATA drives in HP ProLiant server?

Does anyone know if I can install normal 2.5" SATA drives inside an HP DL360 G5 server? Right now it has 6 72GB SAS drives. I am looking for raw storage for my files SAS performance in not required.
1
vote
1answer
82 views

HP SL250s will not boot from the network, does not appear to DHCP

I have an HP Proliant SL250s Gen8 (right-hand) server which is apparently not able to boot from the network. If I configure the system to PXE boot in the BIOS, or if I hit F12, it does start up the ...
1
vote
1answer
354 views

Fastest server ram configuration for 48GB?

I have an HP ProLiant DL160G6 server, with 2 CPU's and 48GB ram, with following modules: 4x 8GB Module - DDR3 1066MHz (KTH-PL310Q8/8G) 4x 4GB Module - DDR3 1333MHz (KTH-PL3138/4G) I'm re-purposing ...
2
votes
2answers
320 views

HP DL380G6 + MSL2024 LTO6 SAS : Which HBA? [closed]

I'm going to upgrade our backup server and I'd like to confirm that the following specs won't choke after the purchase. It'd be great if you could tell me your opinion Our current setup is: HP ...