-5
votes
1answer
43 views

Hdd for server, will it work? [closed]

i have a server : IBM System x3250 M3 its have 2 HDD slots, but currently only have 1 HDD, that is : HDD 500 TB Hotplug, sata, with part number 9CA154-176 i want to add one more HDD, but i only ...
0
votes
1answer
26 views

Using Seagate 3TB drives with a Dell PERC 710 - do I have to worry about align and sector size?

I'm going to setup our new server with 8 3TB HDD from Seagate. They come, as far as I know, internally with 4K sectors. I've run this past weekend some burn-in tests on the disks, before setting them ...
-1
votes
1answer
33 views

mdadm reports faulty disk, but smart doesn't find problems

I've got a 9 disk raid 5 array. Today i got a mail from my server: This is an automatically generated mail message from mdadm running on Eldorado A Fail event had been detected on md device ...
0
votes
2answers
28 views

Wiping hard drives in an IBM DS3512

I have an IBM DS3512 RAID storage device, which I'm planning to sell. How would I reliably wipe my data off of all the hard drives? As far as I can tell, it abstracts away all direct access to the ...
3
votes
1answer
102 views

Steady red light on 2 HP SAS drives in RAID 1

I have a HP ProLiant web server with two HP 300GB SAS SFF 2.5 inch drives (Model: HP 507127-B21). Both drives have a solid red light, however there is no indication within the management software that ...
0
votes
1answer
86 views

Degraded RAID1 on debian 7.5

I am in a bit of a problem with my root server and a degrading RAID. Unfortunately, I'm no expert when it comes to RAID. System informations: Debian 7.5, SSD software RAID1, problem occur since a ...
-2
votes
2answers
272 views

Dell Power Edge R515 - Replacing a Bad Hard Drive in a RAID

I've ordered a new hard drive to replace a bad one in a Dell Power Edge R515. The manual covers obvious topics regarding physical replacing of hard drives, but I've never done this before on a ...
8
votes
4answers
747 views

SW SSD Raid 1 over HW RAID 10

A provider(data center) recommended I go with 1TB SSDs in a software RAID 1 over HW RAID 10 with mechanical drives. Their quote: Typically SSDs are most reliable than RAID cards and since you ...
1
vote
2answers
119 views

Identifying failed hard drive in RAID

I have a server which is running customized version of Debian. It is attached a sun storage raid. It has very limited tools and installing new tools is not allowed. :( This message I see in dmesg: ...
-2
votes
1answer
43 views

Amazon EBS Durability

According to this link: http://aws.amazon.com/ebs/details/#availabilityanddurability It said: Amazon EBS Snapshot can expect an annual failure rate (AFR) of between 0.1% – 0.5%, where failure ...
3
votes
1answer
135 views

How often should I scrub my RAID?

In general I would like to know how often a RAID array needs to be scrubbed. What contributes to the need to scrub more often (reading data?, writing data?, unexpected shutdowns?, drive age?, drive ...
1
vote
0answers
460 views

HP Dl360e Gen8 Not Detecting Hard Drives

I have a new HP Proliant DL360e G8 and it is not detecting the hard drives. We are using both non-hp, and official hp hard drives from an older server (DL120). Hard drives are 3.5" and they are not ...
1
vote
1answer
660 views

LSI MegaRAID SAS 9261-8i: Disk isn't recognized after replacement

I've got a Supermicro Server with an LSI MegaRAID SAS 9261-8i Raid Controller inside. There were 3 Disks attached to the controller which were configured as RAID5 array. One of the disks failed ...
1
vote
0answers
48 views

Unable to access disks in rhel 6.5

I work for a biology lab. We recently bought a new microscope that produces an enormous amount of data - it is simply not feasible to store it on a desktop. So, we bought a storage server - the idea ...
4
votes
1answer
330 views

How to access SMART attributes when using RAID with a Dell Perc 4e (LSI)

I can't easily shut down this windows server, so I'd like 'online' solutions. I tried the following unsuccessfully: Seatools Enterprise: caused a BSOD smartmontools: scan only showed virtaul RAID ...
0
votes
1answer
65 views

Error at partitioning disk

I am struggling to install debian squeeze (64 bit) OS in the system which is having RAID 1. While partitioning the drive, It says an error Operation not permitted during write on /dev/md126 . I am ...
0
votes
1answer
505 views

How to diagnose failed drive on server with raid storage controller?

I have problem with one of my Dell PowerEdge R210. Machine is with Centos 6, today system logs started to inform that the hard drive is failing. Jan 6 03:20:12 centos6 kernel: LSI Debug log info ...
1
vote
2answers
86 views

How can it be that mounting and unmounting takes hours to complete?

I am running an Ubuntu server 10.10 machine with 24 hard disks (and two OS drives). I am using a script to mount all the drives to their desired mountpoints. This works pretty fast, as expected, ...
0
votes
2answers
128 views

Expandable Linux filesystem w/ redundancy & support for different drive sizes?

I did a bit of research already and didn't come across any filesystems so far that have the following features: Expandability, Redundancy, and the ability to utilize the full capacity of different ...
0
votes
1answer
290 views

Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from ...
2
votes
3answers
7k views

Reinserted a RAID disk. Defined as foreign. Is import or clear the correct choice?

I have re-inserted a RAID disk, on a DELL server with Windows Server 2008. The drive-status indicator was changing between a green and amber light, and the monitor gave the following message: ...
0
votes
2answers
115 views

Replacement Alternative for Dell FY606 in a Poweredge T105

I have recently upgraded my Poweredge T105 server to use a SAS 6/ir RAID controller. Unfortunately, I did not realize at the time that adding the card would cause the BIOS to complain about a missing ...
1
vote
3answers
504 views

How to identify faulty drive on a HP DL160 G6 - P410 Smart Array

I have a HP DL160 G6 Server with 4 HP SAS drive, firmware have been updated to the latest on the HD and the Smart Array... The issue im having is that one of the disk have a steady amber light turned ...
2
votes
1answer
169 views

Is my hard disk failing?

I've just had the hard disk on my server replaced. It was part of a RAID 1 array. The sdb1 partition keeps failing every few hours now. # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] ...
0
votes
0answers
143 views

Half of disk space missing on RAID1, all disks it seems to be ok

Hi there. I have a problem with raid array. I miss it a half. My disks layout is 2 x 250 gigabytes velociraptors (Array_0000) 2 x 1TB velociraptors (Array_0001) ....both connected in RAID1. OS ...
-2
votes
1answer
53 views

Preparing for RAID5 failure [closed]

I've got an Ubuntu system with a bunch of hard disks in it acting as my home router, DHCP server, file server, etc. Twice in the past 24 hours it has suddenly decided to set the root filesystem to ...
0
votes
3answers
161 views

RAID 5 with two failed devices

I have a software RAID 5 with 6 devices and one of them needs to be rebuilt. Until now, everything is OK. But, while the disk is rebuilt, it was found bad sectors on another disk and is being marked ...
2
votes
1answer
52 views

Benchmark individual drives in RAID5

I'm running a server with 3 RAID5 arrays through an ARECA 1880i coupled with a HP-SAS Expander. After experiencing a massive degradation in performance lately, I want to benchmark the drives ...
2
votes
2answers
78 views

Progressive upgrade of a RAID array

I have a 16 disk backup RAID6 array. Currently, those 16 disks have the following specs; 500 GB 16 and 64MB cache 3 Gb/s SATA I would like to begin upgrading these disks if possible, primarily ...
0
votes
2answers
934 views

Software for RAID Failure Alerts?

I have two 256 GB Samsung 840 Pro SSD disks in a RAID 1 array. I would like to receive a notification if one of the disks in the array fails. Can anybody recommend an application I can install on the ...
0
votes
1answer
2k views

How do I detect whether my Hard Drive is RAID configured?

I'm not certain if this question makes complete sense. I'm trying to find out if a server is RAID configured. The Device is HP Proliant SCSI, but that's all I know, it's a terabyte drive. I've used ...
4
votes
3answers
607 views

RAID - buy spare disks at same time as originals?

When using RAID1, is it best practice to buy spare disks at the same time as the original disks to ensure you have the identical type in case they become unavailable in future?
-2
votes
1answer
254 views

SATA disks instead of SAS - DELL 2950 [closed]

I have a DELL 2950 with a PERC5/i controller and a SAS backplane and my intention is to switch to SATA on the cheap. I don't even have drive trays. This backplane has SAS ports. I just bought 2 ...
-2
votes
1answer
97 views

mini-SAS SFF-8087 xy connector and 24 hard drives? [closed]

I have 24x drive 4U case with 4U Expander Backplane http://www.supermicro.com/products/chassis/4u/846/sc846e16-r1200.cfm MegaRAID SAS 9260-4i RAID Card ...
0
votes
1answer
200 views

Will configuring a server with RAID 5 and (2*500gb) + (2*1TB) work?

I'm currently setting up a DELL server, which came with 2*500gb disk drives but is configured in RAID 1. I want to increase the total capacity of the disk storage to at least 1TB. Now with it being ...
0
votes
2answers
421 views

RAID 1 hard disks errors, file system is not mounting

I have a Server with 2 HDDs in soft RAID 1, the OS is Debian Wheezy. After some database testing, the file system has gone to read-only mode, after which I have rebooted the machine. The server is not ...
-1
votes
3answers
290 views

Raid 0, Raid 1, Raid 5, Raid6, Raid 10 Read/Write performance? [duplicate]

Assume a single disk has a baseline of 1W & 1R performance, how does the different RAID configurations behave? My initial guess: Raid 0: 2W 2R Raid 1: 1W 2R Raid 5: ? ? Raid 6: ? ? Raid 10: ...
2
votes
2answers
287 views

RAID 10 — how do you know a drive is going or is bad?

I have some servers with a datacenter all the servers have RAID 10 setup. How do I know when one of the drives is going bad or is bad and needs to be replaced? EDIT: These servers are unmnaaged and ...
0
votes
1answer
127 views

Is there anything I can do with a software RAID 1 on linux to workaround temporary 'bad' sectors?

Basically I have two identical hard disks that are in perfect working order, they just don't have the vibration tolerance they need for the environment they are in. (I am making an educated guess that ...
1
vote
1answer
171 views

HDD compatibility to rebuild for RAID

Last year we build a RAID 1 with Western Digital 2 TB drive model number WD20EARS. Unfortunately one of the drives failed. We are unable to find any new drives of the same model number. What do we do? ...
0
votes
1answer
765 views

3ware 9500S-4LP - Replacing faulty drive

An old Windows 2003 server is running on a 4 disks (each250GB) RAID 5 array, attached to a 3Ware 9500S-4LP unit. This morning I got two alarms from the controller: - 0x04:0x0025 Cache flush failed; ...
-1
votes
2answers
109 views

The device, \Device\Harddisk4\DR37, has a bad block

I've received the error below and wondering if it's something I should be worried about? I've checked the RAID controller and all are functioning without errors. Log Name: System Source: ...
0
votes
1answer
184 views

RAID 1 Failure - Unable to boot to single drive

This is sort of baffling me. A computer we manage had a series of failures causing one of the hard drives (SATA Port 0) to fail. The drive still recognizes that there is an OS on it but fails to boot ...
0
votes
1answer
159 views

Windows 2003 Near Freezing

Problem: Our server becomes very very slow (near freezing) if I copy a file from any directory on C: and D: to any other directory. In short It becomes very slow if I touch the hard disk. Currently I ...
3
votes
1answer
387 views

RAID-5 or RAID-6 - is RAID-5 really that bad? [duplicate]

Possible Duplicate: Which is better: RAID5 + 1 Hotspare / RAID6? I need to decide myself between RAID5 and RAID6. The servers have a hardware-RAID controller and 6 drives each. The ...
3
votes
1answer
1k views

Smart Array P400i Physical Drive failed after being replaced

We have replaced the bad drives in a few HP systems (ProLiant DL360 G5), but they continue to show failed. The drives are part of RAID, and I think this might be why they are appearing as failed. The ...
0
votes
1answer
2k views

end_request: I/O error, dev sda, sector xxxxxxxxx

I have a IBM server. This server contains 3 hard disk with RAID 5. It was working fine earlier. Unfortunately this machine got the following error message. After that I have rebooted the systems. ...
0
votes
1answer
46 views

Server upgrade configuration - raid vs. multiple drives vs. combo raid / backup

We're upgrading our Linux box, and moving from CentOS (quad core AMD, 8GB RAM, SATA drive) to RedHat OS (dual quad core Xeon, 8GB RAM, SAS drives) and was wondering... what will provide the best ...
1
vote
1answer
603 views

How to detect hard disk failure?

So, one of my servers has a hard disk failure. It's running software RAID, the system locked up and according to /proc/mdstat (and /var/log/messages), it's really down: Personalities : [raid1] md2 : ...
21
votes
4answers
1k views

Do raid controllers syncronize HDD platter rotation?

I'm in the market for a new storage solution. While researching various specs one of my coworkers said that some raid controllers can synchronize HDD rotation to the effect of all drives' sector/block ...