1
vote
0answers
108 views

Need help recovering RAID 6 array

My CentOS 6.5 server had its primary drive fail the other day. Our hosting company replaced the primary drive and reinstalled the OS. The system is up and running, but the 15TB of RAID6 storage isn't ...
2
votes
1answer
135 views

Concerns of simultaneous failure of SSD Raid1

Since SSD's have a write limit requiring wear leveling one would assume that all things being equal 2 identical SSD drives would wear nearly identically if they mirror data writes. When one drive ...
2
votes
2answers
74 views

Progressive upgrade of a RAID array

I have a 16 disk backup RAID6 array. Currently, those 16 disks have the following specs; 500 GB 16 and 64MB cache 3 Gb/s SATA I would like to begin upgrading these disks if possible, primarily ...
0
votes
1answer
619 views

3ware raid controller, unit unusable, several degraded disks

I was switching the disk drives in my server, running RAID 6 on 5 disks on a 3ware 9650SE controller, for newer disks and have run into a problem. The two first disks went fine, I took out one disk ...
3
votes
1answer
363 views

RAID-5 or RAID-6 - is RAID-5 really that bad? [duplicate]

Possible Duplicate: Which is better: RAID5 + 1 Hotspare / RAID6? I need to decide myself between RAID5 and RAID6. The servers have a hardware-RAID controller and 6 drives each. The ...
0
votes
1answer
313 views

mdadm: superblock on /dev/sdd1 doesn't match others - assembly aborted

OS: Debian Squeeze Kernel: 2.6.32-5-amd64 mdadm version: 3.1.4 (31 August 2010) mdarrays md1 = raid1 (this is working) (devices: /dev/sd[fg]1) md0 = raid6 (previously raid5, ...
4
votes
1answer
2k views

3Ware 9650SE RAID-6, two degraded drives, one ECC, rebuild stuck

This morning I came in the office to discover that two of the drives on a RAID-6, 3ware 9650SE controller were marked as degraded and it was rebuilding the array. After getting to about 4%, it got ...
-1
votes
1answer
396 views

3ware 9650SE-24M8 INOPERABLE data recovery

I have a raid6 array with 16 hdds. Two harddrives had failed (device error), but when I went to replace them, I pulled out one wrong disk! Now the raid array is INOPERABLE. Is there any way to ...
9
votes
2answers
844 views

Areca 1280ml RAID6 volume set failed

Today we hit some kind of worst case scenario and are open to any kind of good ideas. Here is our problem: We are using several dedicated storage servers to host our virtual machines. Before I ...
3
votes
3answers
641 views

Is it safe to write data to a RAID 6 while it's rebuilding?

I have a test RAID controller on my network which hosts a very large RAID 6 (11 drives, 3TB each). One of the drives failed, and the array is now rebuilding. At this rate, I think it will take about 3 ...
3
votes
1answer
187 views

mdadm raid6 recovery reads more from one drive?

I just replaced a fault drive in my raid6-array (consisting of 8 drives) during the recovery I did notice something strange in iostat. All drives are getting the same speeds (as expected) except for ...
1
vote
1answer
5k views

LSI MegaRaid warning: Patrol Read can't be started

We run a HyperV server on RAID-6 (the OS is Windows Server 2008 R2). The hardware is LSI MegaRaid SAS 8704EM2 controller, with 4x 1TB WesternDigital SATA drives. The server is up & running on this ...
0
votes
2answers
469 views

How to identify RAID (5 or 6) controllers that allow dynamic resize of the array

I'm building a server with a RAID5 array, based on a hardware controller. I want to be able to later add additional disks and have the array rebalance across all of the disks, enlarging the usable ...
3
votes
2answers
814 views

How to diagnose intermittently slow raid data transfer rate?

I have an encrypted RAID6 set up on Centos 5.5. When I transfer a large 10gb file from the raid to my computer it will pause at around 4-5gb and again at 9gb. The data transfer drops from 25mb/sec to ...
1
vote
2answers
1k views

RAID6 setup - adding additional drives

I want to setup a dedicated server. To begin with we need a minimum of 8TB. I believe I can begin with 6x2TB drives in a RAID6 setup to achieve this. Now when I need to increase this capacity to ...
1
vote
3answers
824 views

mdadm & raid6: does “re-create(with different chunk size) + resync” destroy orig. data?

I would like to rescue data on my software raid-6 array. I did some stupid actions (described bellow) with this original array. Main Question: I need to know if original data stored on raid-6 array ...
1
vote
5answers
755 views

RAID 6 to RAID 1 with mdadm

My home network is changing and I am moving my file storage solution away from my Ubuntu server and onto a Drobo FS. I currently have 6 500GB hard drives in a RAID 6 array providing 2TB of capacity. ...
1
vote
3answers
2k views

RAID Virtual Disk Configuration / Partitioning in Operating System?

I have 6 x 1TB SAS for my new server. I want to create 3 partitions: one for OS, one for Virtual Machines, one for share data. There are 2 options for me: Option A: Create 3 Virtual Disks in RAID ...
2
votes
2answers
244 views

Remove second RAID6 drive during resync from first failure?

I have a RAID6 comprised of five 1TB drives in good working order. I'd like to redistribute the array differently in my system (change the drive distribution over controller cards). I pulled the first ...