0
votes
1answer
95 views

access same subnet on different interfaces

I have a router with external (WAN connection) subnet 192.168.1.0/24 and also on same router a tunnel to a remote location which have the exact same subnet (192.168.1.0/24), and i need from my LAN to ...
0
votes
1answer
30 views

DHCP wont release allocated IPs [closed]

I have a TP-Link td28151 router and I am using DHCP. I need to connect 40 devices to my router by Ethernet. I have set the count of my clients to 100, and my subnet mask is 255.255.255.0. I have ...
0
votes
0answers
23 views

Command “ip rule show” not showing anything

I try to list all routing rules, and as far as I know this should be accomplished with the "ip rule show" command. In my case there is nothing returned (really nothing at all). Why? Could it have to ...
1
vote
0answers
18 views

Static routing doesn't route correctly

I have Router 1 and Router 2. For R1 I have 1.1.1.1 with /24 mask, for R2 I have 1.1.2.1 with /24 mask. R2 is connected to R1 interface with 1.1.1.2 address. Following image shows my topology ...
0
votes
2answers
64 views

What ISP needs to provide in order to route native IPv6 /56 range to several VLANs

I have a theoretical question. Network topology is like this: ISP <--- eth0 -> Router1 <- eth1 ----+--> VLAN1 '--> VLANx For the sake of ...
0
votes
0answers
95 views

Creating a multi-wan/isp failover router where wan IPs are dynamic on Debian

I'm having an incredibly hard time creating a basic router on Debian which has connections to two ISPs where the ip addresses are dynamic. I don't need bonding, I really just need some way to detect ...
0
votes
1answer
131 views

How to forward traffic to VPN device

I have set-up OpenWRT in a virtual machine which acts as a router. It has two network interfaces: br-lan: connected to vm internal network eth1: connected to internet through host via NAT I have ...
0
votes
1answer
113 views

HP MSR 30-10a Router - Route Traffic over Default Route

We have a brand new HP MSR 30-10a Router. We have a fairly simple routing situation - we have two IP blocks, one which has a route out. We need things on the first block to go through the router, and ...
0
votes
1answer
42 views

Reachability with OSPF on firewalled network

I'm trying to figure out how OSPF establishes routes when used on a network with firewalls. Say I have four routers (A, B, C, and D) and two firewalls (F1 and F2), arranged like so: (LocalA) A - F1 ...
0
votes
0answers
75 views

Can we use ICMP redirect message to pass routing information among interior routers in an autonomous system ?

Can we use ICMP redirect message to pass routing information among interior routers in an autonomous system ? why or why not? I know that routers send out ICMP redirect message if they find a better ...
-5
votes
2answers
218 views

Can a computer route IP trafic between two LAN if it is not configured as gateway? [closed]

Having two LAN, each one have its own gateway, DHCP and internet connexion LAN 1 - IPs: 192.168.0.0-255, Mask: 255.255.254.0, Gateway: 192.168.0.1 LAN 2 - IPs: 192.168.1.1-255, Mask: 255.255.254.0, ...
0
votes
1answer
54 views

HP MSR20 Router VPN Questions

I have limited experience with routers, I was wondering if some offer some insight. I am considering deploying a series of HP MSR20 (or similar routers) at a number of satellite offices which have ...
0
votes
2answers
582 views

OSPF routers (with BIRD on debian) recognize each other as neighbors but can't ping each other

I've created a "line" topology using virtual box - creating 4 machines and making a separate link between each using internal networks - R1 (eth0, 10.0.1.1) <-> (eth0, 10.0.2.1) R2 (eth2, 10.0.2.2) ...
0
votes
1answer
65 views

Can ESXi host get IP from VM DHCP Server?

I have a server with 2 nics, 1 is public and 1 is private, the private nic is connected to a switch which is the LAN. Can the ESXi host draw an ip address and get service through the LAN just like the ...
0
votes
2answers
120 views

Ubuntu Server SSH Connectivity Issues (Potentially Router) [closed]

I have a server set up with Ubuntu 12.04. I've installed OpenSSH, and I'm trying to access it from another computer, on another network, using this command (modified for the correct values): ssh ...
1
vote
0answers
83 views

Why might one host be unable to access the Internet, when it can ping the router and when all other hosts can?

I have a Draytek Vigor 2830n. It's kicking out a 192.168.3.0 LAN. It performs load-balancing across dual-WAN ports, although I've turned off the second WAN to simplify testing. There are many hosts ...
-2
votes
1answer
44 views

vlans communicate with each other

I am setting up three vlans in a cisco router with the following configurations. Vlan 10 Subnet: 192.168.1.0/24 Netmask: 255.255.255.0 Gateway: 192.168.1.1 Vlan 20 Subnet: 192.168.2.0/24 Netmask: ...
-1
votes
1answer
111 views

Linux server not routing my packets

I have a linux server (Ubuntu 12) with 2 NIC's. eth0 is connected WAN (inet 10.0.2.15 mask 255.255.255.0) eth1 is connected LAN (inet 192.168.0.1 mask 255.255.255.0) I want my windows machine to ...
1
vote
1answer
98 views

How can I access my router that is on other office network

Hi I'm working on ROUTER A and I want to access ROUTER C, the config is: ROUTER A <-conected with-> ROUTER B <-conected with-> ROUTER C ROUTER A: LAN:192.168.1.1 255.255.255.0 ...
1
vote
2answers
129 views

Routing to a floating IP between 2 servers on different networks

I have two servers in two different network subnets, there is a heartbeat between the servers and they automatically select active / standby. the active server will have a floating IP assigned to one ...
-2
votes
1answer
156 views

OSPF configuration in packet tracer

assume that I have 4 buildings which all connected to main building and in each building I have privileged subnet ( red circles ). privileged subnet must be able to connect each other, and rest of the ...
0
votes
2answers
348 views

cisco ip nat / port forwarding

I have been trying to get port forwarding working with a newly installed cisco router. I cannot seem to find where my fault is and have been looking for quite a while. The relevant section of my ...
0
votes
2answers
128 views

Debian router drops connection [closed]

I have a home network with a debian server running kernel 3.8 setup as a router, doing DHCP, DNS-caching, samba and Squid. The motherboard is a Gigabyte GA-Z77X-UD5H with two ethernet ports, one Intel ...
0
votes
2answers
95 views

Juniper Router - Load Balancing

I have a single Juniper router which is connected to multiple external ASs. I am looking to load balancing for best way to automatically move traffic away from one link the others (without hardcoded ...
0
votes
2answers
149 views

Can I use a software router to filter traffic coming from a Cisco router?

I have the following topology working but i would like to be able to filter the traffic using a software router such as Zentyal. Current [INTERNET] === [Cisco 2600] ===[Cisco Switch] === [Machines] ...
1
vote
1answer
1k views

Routing between two routers with static routes

I have a Draytek 3200 router and a pfsense rackmount router that I am trying to get to route to each other. I have a subnet on each router and a subnet for the link between, as shown here: As it ...
0
votes
2answers
167 views

Routing from one router to another?

I'm trying to route from one basic router to a pfsense box. It's basically so that I can have VPN users on both router aswell as VPN tunnels to test which router performs best. I am also trying to ...
1
vote
1answer
79 views

Why can't I reach the LAN side of a slave vrrp router?

I have a dual linux firewall/router setup that is connected to 2 different upstream providers. Internally the default route is a failover using vrrp. The setup looks something like this. The routes ...
4
votes
2answers
241 views

EIGRP neighbors flapping

I have a EIGRP topology set up in GNS3. It looks like this: The neighbor relationship between R7 and R8 is constantly flapping and I cannot figure out why. Hello timers and time delays are all set ...
1
vote
1answer
255 views

DMZ config on RV082 router

We are connecting 2 offices with a dedicated point to point connection. Both offices have the Cisco RV082 router. In both offices, the routers are being used for internet on the WAN1 port. This ...
1
vote
2answers
111 views

Performance Impact of adding more NIC cards to a Linux router box

What would be the impact on performance if more and more NIC cards are added to Linux box for routing traffic to different networks. Lets say i have 10 different networks and i only have a single ...
-1
votes
1answer
124 views

how do i automatically add a new route to the routing table?

I'm looking at linking two networks with a long range Ethernet bridge. I know I can connect my two networks with a router, but my problem is how will my computers know where to send packets if I don't ...
1
vote
1answer
315 views

Fritz!Box IPv6-Address different than IPv6-Prefix

In my Fritzbox it states the following: IPv6-Adresse: 2a02:8070:600::14b6:c7******, Gültigkeit: 100465/86065s IPv6-Präfix: 2a02:8070:62c:3200::/56, Gültigkeit: 100464/86064s I am not able to ...
0
votes
1answer
118 views

Connectiong adsl router/modem and router with bridgemode

I have one adsl modem/router which is not "top" of the line and it lack allot of options which I need. I was able to acquire one Cisco router recently which has all options that I need ( like DMZ, ...
2
votes
2answers
456 views

Routing using Linux with 2 NIC cards

Configured Clear OS to be in Gateway mode on a machine with two NIC cards. eth0:192.168.2.0/24 with ip 192.168.2.27 which is connected to a modem and thus have internet connectivity. ...
0
votes
1answer
67 views

How do I setup a network that would allow both wired and wireless clients to go through a proxy first?

In my current setup, I have a NETGEAR Wiressless-N Gigabit router WNR3500NL and a 3COM 10/100 24-pt switch. The router has 5 ports, a single Internet port(yellow) followed by 4 Ethernet ports(orange) ...
-4
votes
2answers
93 views

How to access an IP address as if on a different network using SSH [closed]

In preparation for a lengthy business trip, I set up my router such that I can access my home computer over the internet via port forwarding over SSH. One thing I neglected to do was setup access to ...
-2
votes
2answers
186 views

Network traffic across different (sub-)nets, how does the route get determined? [duplicate]

Possible Duplicate: How does Subnetting Work? Imagine there is a small network with 2 subnets. Both of the subnets have their own switch (means: all machines on that subnet share the same ...
2
votes
2answers
569 views

Layer 3 switch routing

I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I ...
0
votes
2answers
884 views

Set up router with 2 WANs and multiple subnets

I'm trying to set up a Debian box as a router for an office. I need to have 3 subnets in the LAN and 2 WAN connections, and I want one of the subnets to ALWAYS use WAN 1 and the other subnet to ALWAYS ...
0
votes
2answers
2k views

How to route/redirect my Internet traffic through another router/node on the net?

I am trying to access some content on the Internet which has some stupid geographic restrictions (access limited from a specific country. Most likely the restriction is IP based. I happen to have ...
3
votes
3answers
2k views

How do I get internal hosts to use a VPN connection set up on a FreeBSD router?

Question in short: How do I get traffic from a host on an internal network, using NAT behind a router, to use a VPN connection set up on the router? I have a FreeBSD 9 router with 4 network ...
-2
votes
3answers
1k views

Packets dropped due to NAT? Firewall? Unroutable private IP addresses?

Preliminary note This question is out of academic interest. I know how to work around the limitation. I use this setup to control access from one subnet to the other on IP level which works great so I ...
0
votes
1answer
484 views

default route propagation under rip - quagga

How would I propagate a default route under RIP, from a router? The operating system is Ubuntu. Can this be done in Quagga? What would be the command? I found a solution for a cisco router: ...
1
vote
1answer
253 views

More than 8 WAN aliases on routers?

We have a Draytek Vigor 2820 in our office and we have a few servers running websites and email applications. These servers each have their own public ip using WAN aliases that are mapped to their ...
2
votes
2answers
4k views

Routing between subnets with one router?

I have a Draytek Vigor 2820 which is connected to three gigabit Netgear Layer 2 switches. Currently the network is fairly simple, 192.168.1.0/24. One the network I have 7 servers, around 50 ...
0
votes
2answers
145 views

Linux as a router for public networks

My ISP had given me a /30 network. Later, when I wanted more public ips, I requested for a /29 network. I was told to keep using my earlier /30 network on the interface which is facing ISP, and the ...
1
vote
2answers
3k views

Configure Mac OS X Server as Router?

I'm trying to configure a Mac OS X box with two NICs as a router complete with DHCP and NAT which in theory shouldn't be too much of a challenge but at the moment I'm learning theory and reality are ...
3
votes
1answer
2k views

OpenVPN redirect-gateway does not work on Windows 7?

i have set up openvpn, and it works. pinging from client to server and backwards works just fine. but now i wanted to redirect all the clients traffic through the vpn. so i did the following steps as ...
0
votes
1answer
312 views

Bridging and routing IPv6 Router Advertisements

I have a bridge called "br01" in which the interfaces "eth1" and "eth0" are participating. There is a rule in the broute table of ebtables that drops RAs when they arrive in the interface eth1, so the ...