Serial Attached SCSI (SAS) is a computer bus used to move data to and from computer storage devices such as hard drives and tape drives. SAS depends on a point-to-point serial protocol that replaces the parallel SCSI bus technology that first appeared in the mid 1980s in data centers and ...

learn more… | top users | synonyms

1
vote
1answer
34 views

HP DL360 G5 RAID controller not recognizing drive bays 5 and 6

I have an HP DL360g5 bios P58. With a Slot 0, HP Smart Array P400i Controller (256MB v2.08) The server originally was running Windows Server 2003 with 2 72GB 15k SAS drives in RAID0. One of the ...
4
votes
1answer
36 views

SAS balancing vs Network balancing

I want to configure file server in MS Windows Server 2012 R2 environment, which would load balance traffic. I have got a SAS disk array with 2 SAS controllers which is connected to 2 Hyper-V cluster ...
1
vote
0answers
27 views

Dell r730 + Dell 12Gb SAS + Centos 7 + netvault 9.2 quantum superloader 3 not found

In the above configuration Netvault does not find the library attached to the sas controller. What driver should I see with lsmod for the SAS card? I have: ... mpt3sas 195379 0 ...
0
votes
0answers
23 views

Is there a way to disable or hide SAS drive on LSI SAS 3008 controller?

I am setting up Dell Precision 7910 workstation that has LSI SAS 3008 controller and 2 SAS drives connected to it. It came with Windows 7 installed on drive with smaller drive number (0x09 on LSI bus ...
6
votes
1answer
3k views

replace controller, add second controller, or use expander?

I have a Proliant DL380 G6 that I am re-purposing as a Hyper-V host for a new, off-site data center that will host our DR services. The server currently has a P410i controller with the 512MB BBWC ...
1
vote
0answers
9 views

SAS direct dual link connection to an embedded LSI Fusion-MPT controller

This is a hardware question. I have a dual-link SAS hard drive and a Intel S5000XVNSAS motherboard without the drive cage option. Recently, I bought a direct dual-link cable ...
3
votes
2answers
60 views

Max SAS throughput of a disk stack?

I've been trying to figure out something. I have a stack of SAS shelves (attached to a NetApp if that's relevant). Each devices within the shelf is 6G SAS. According to the vendor, the sustained ...
3
votes
1answer
59 views

SFF-8087 cable and connector variations causing fault?

I recently bought a set of 6 cables to connect my LSI MegaRAID card to my Norco-4224 backplane. The connector on both ends is SFF-8087. However, when they arrived, the disks would not be detected. ...
2
votes
2answers
174 views

Redundant Paths between DELL R720 and MD3420 in ESXi 5.5

We had some trouble configuring redundant paths between a DELL R720 and MD3420 storage connected via two LSI 12GB SAS-HBAs using ESXi 5.5. The datastore was accessible and worked fine, except for the ...
0
votes
2answers
36 views

daisy chain SAS tape drives?

I need to add a second SAS Tape drive to my server. I have a second PCI-E SAS card, however I don't have any free PCI slots in the server. Is there any way to daisy chain external SAS devices together ...
0
votes
1answer
35 views

IBM BladeCenter S: How to configure new SAS disks

I have an IBM BladeCenter S, and I have added two new 450GB SAS disks. I want to configure the disks as a RAID 0, and assign the new disks to one of the servers in the Bladecenter. When I connect to ...
0
votes
2answers
45 views

What types of workloads require SAS disks compared to SATA?

I am looking to outfit my new server (new to me) with larger capacity disks. The server right now has 4 SAS 146GB disks in it. My original thought was to just buy larger SAS disks and replace or add ...
0
votes
1answer
657 views

Install SAS/SATA backplane in Dell PowerVault 220S

Is the backplane of a Dell PowerVault 220S svc tag 3sdpcb1 (14 drive, 80 pin hot swap scsi) upgradeable to a SAS/SATA backplane & controller card replacement? The unit already seems to be quite ...
2
votes
1answer
147 views

Cabling for SAS drives in a Dell T420 with Perc H710

After having purchased a Dell T420 with SATA drives and without RAID, and discovering this was a mistake for performance reasons, I'm obtaining a Perc H710 PCI card and SAS drives. Now I'm stuck with ...
1
vote
1answer
78 views

What kind of Dell Perc H710 card is a “VM02C”?

A number of vendors (e.g., on eBay) sell a Perc H710 card they say is a part number VM02C. However, I can't find this in Dell's website, either by looking at every H710 card list in the parts area, or ...
125
votes
6answers
14k views

Are SSD drives as reliable as mechanical drives (2013)?

SSD drives have been around for several years now. But the issue of reliability still comes up. I guess this is a follow up from this question posted 4 years ago, and last updated in 2011. It's now ...
3
votes
2answers
145 views

Slow writes Dell Server R720

I have a Dell R720 Server with PERC H310 hardware raid 5 and 4 x Seagate Cheetah 15K.7 ST3300657SS 300GB hard drives. Windows Server 2008 R2. The reads look good, but the writes are painfully slow. ...
1
vote
0answers
143 views

How to change SAS address on Expander

I have the following setup - two supermicro backplane attached to one controller LSI SAS 9207-4i4e and unfortunately cannot access the disks, during boot there are disks only in one backplane, the ...
0
votes
0answers
25 views

FreeBSD disk device names/targets on LSI SAS9211i (IT)

I have a machine with an LSI SAS card (8 SAS/SATA ports) with 8 drives that were initially named da1-da8. The numbering stayed consecutive (first drive -> da1, scbus3 target 0 lun 0, etc.) until I ...
0
votes
1answer
117 views

How to make Dell PowerEdge R410 boot from two hard drives?

I have a Dell PowerEdge R410 with two SAS drives connected to the SAS controller and I would like that both of them can be in the boot sequence tried to boot. I would like to use md software RAID-1 in ...
5
votes
1answer
642 views

Recovering data from a failed SAS drive? (RAID0…yes, I know)

We have a HP DL360 server with a P400 controller, which has two 72GB 10K SAS drives in a RAID 0 configuration (yes, I know...RAID 0). The HP Model number for the drives is DG072A8B54 Recently, one ...
2
votes
1answer
491 views

ZFS: SAS v SATA - does it matter?

I understand from NEC's white paper, Silent data corruption in disk arrays, that: some SAS drives should have a "T10-DIF" feature to detect silent data corruption; whereas "There is no standard for ...
7
votes
5answers
1k views

ML350 G5 - upgrade hot swap drives to 6 Gb/s?

I support a non profit. They got an ML350 G5 donated to them and I immediately put it to good use for them :) It came with four HP 300GB 15K SAS drives - and of course, they have all now failed. I ...
3
votes
1answer
112 views

Can I recover my raid after blown backplane / mobo?

We had a catastrophic server failure the other day. The server was the head to our NAS. Multiple disk shelves were attached via SAS (SFF-8088 to a HP Smart Array RAID Card). Also connected to the RAID ...
19
votes
2answers
585 views

Sanity check on 40TB server configuration

I've got 40 years in computing, but I've never had to build a server quite like this one, so this might be a n00b question. I have a client that is going to offer ultra-high def music files for ...
1
vote
1answer
80 views

connecting HP gen 5 SAS raid cage to a third party (3ware, LSI) controller?

I have a ML350 G5 that I'm thinking of repurposing to save money. I'm looking to install FreeNAS but it (ZFS) doesn't play nice with the HP e200i card that's part of the motherboard from what I've ...
2
votes
2answers
1k views

How can I enumerate SAS addresses/WWNs in Linux?

I have some SAS devices in a server, I would like to find out what their SAS addresses are. How can I do that in Linux? I'm using CentOS 6.
0
votes
1answer
39 views

Understanding SAS transfer speeds

I've been tasked with building some large storage and i'm first working to expand my SAS knowledge. As i consider transfer bottlenecks and SAS speeds, i can't help but wonder how 12 Gb/s SAS equates ...
0
votes
1answer
2k views

HP ProLiant ML350e Gen8 v2 Not Detecting Hard Drives

I have tested several solutions but non of them cant detect my 2 hard drives (legacy mode , acpi and raid embended) I have a 2 Dell-Seagate SAS Cheetah 15k,7 hard drives (ST3300657SS) (they are not ...
1
vote
4answers
359 views

Do Equallogic PS6010s accept non-EQL firmware disks?

We have a PS6010 which is just out of its support contract. We are looking to give it another lease on life so would like to replace all the drives with new ones. It currently has 16x ...
1
vote
1answer
352 views

ProLiant DL380p not recognising HP hard drives on boot

I have two ProLiant DL380p rack mounted small factor servers. I have installed the following drives onto both servers: 1x 240GB SSD drive (Crucial NOT HP branded) 2.5" SATA 7.2k rpm 1TB ...
1
vote
1answer
1k views

How to upgrade the firmware of HP SAS expander card without Smart Array controller or Proliant Server?

How can I update/upgrade/flash the firmware of an HP SAS expander card [468406-B21 a.k.a. 487738-001]? I used to do this using Windows and a HP P410 Smart Array controller, however that controller is ...
1
vote
0answers
180 views

HP Proliant ML350 G5 - smart array initializing

I have a big problem with a HP ProLiant ML350 G5 with 2 SAS HDD 146Gb : it start with the message : "Slot 0 HP Smart Array E200i ... initializing" without any error message. if I test the HDD with ...
4
votes
2answers
282 views

SAS Expander backplane performance drops when more than 8 drives are active?

We are using an LSI 9211-8i raid controller (flashed in IT mode) in a PCI-e 2.0 x8 slot. It's connected to a supermicro SAS 836EL1 backplane with 1 SFF-8087 cable. We have 16 drives installed. When ...
6
votes
1answer
491 views

How do you connect more than 4 drives to a LSI 9361-4i MegaRAID controller?

I’m fairly new to proper hardware RAID having only used it in pre-built server machines before, but on the recommendation of some friends who work for datacentres I’ve bought an LSI 9361-4i MegaRAID ...
2
votes
2answers
4k views

Can IBM System x3650 passthrough SAS?

I am looking at the specs and manual for the IBM System x3650. According to the specs a ServeRAID-8k-l hardware RAID comes standard, but there's an option to upgrade to ServeRAID-8k. If I understand ...
3
votes
2answers
337 views

Hardware mods: kludging a conversion from U320 SCSI to SAS/SATA

I apologise if this isn't an appropriate question for this forum. I've an elderly server that works well and that I'd therefore prefer not to scrap entirely. But I would like to replace the current ...
2
votes
1answer
44 views

Failing drive in RAID10 array; which degraded state will be least punishing on performance?

Running on LSi 9260-16i, with 16 SAS drives (Seagate Savvio 15k.2). One drive is getting media read errors, so we're going to RMA it out. Which of these is the least performance destroying option in ...
0
votes
1answer
68 views

How to enable SAS-12 on LSI 9361 RAID controller

By default, this SAS-12 controller runs with SAS-12 SSDs at SAS-6 speeds. How to unlock SAS-12?
0
votes
2answers
215 views

LSI MegaRaid - Image Drive from Failed RAID

I had a power failure and my LSI MegaRaid 3 disk SAS RAID 0 failed. My attempts to recover the RAID have also failed. I plan to rebuild the array and go with RAID 5 and add another SAS disk. ...
-1
votes
2answers
106 views

Mini-SAS Connector Issue

allow me to apologize in advance, because I am horribly uneducated in this realm, yet I find myself with this problem: My company hired ProMax to setup all of our networking in our office. One of the ...
1
vote
2answers
277 views

Unsupported Storage Connection Detected on HP DL380 Gen8

I'm hoping this is the right place to ask. I recently received a new HL DL380 Gen8 server, on which I want to install Server 2012 R2 via Intelligent Provisioning. According to the specifications, ...
4
votes
3answers
2k views

Why do servers have SAS instead of SSDs? [closed]

I was wondering why do servers still come with SAS disks instead of SSD disks? I know that SAS are faster than normal hard drives but they are still much slower than SSDs. I think they are more ...
0
votes
1answer
467 views

How does loss of DWORD synchronization affect the health of an SAS disk?

I tried to get more information from the error log of an SAS disk by running the following command that prints values and descriptions of the SAS (SSP) Protocol Specific log page. # smartctl -d scsi ...
0
votes
2answers
132 views

1 x Raid card and 6 sata drive over 1 SFF-8087 port [closed]

I have a question regarding LSI00328 LSI MegaRAID SAS 9271-4i Can I connect 6x sata drives to -4i card or I need -8i version
0
votes
1answer
42 views

“Core Charge” on defective server HDDs

I have collected a pretty decent amount of SAS and SCSI disks over the years that have a predictive failure warning. I was just about to throw them all out, but wondered if any of the manufacturers ...
0
votes
1answer
455 views

Bandwidth with SAS expanders and RAID controllers

Having a RAID controller that has eight internal SATA3 lanes, you can get 6 Gb/s on all eight drives. What if I connect a 24 port SAS expander to an eight port RAID controller, do I still get max ...
1
vote
2answers
763 views

Will Intel RES2CV360 SAS Port Expander Work With Adaptec 6805 RAID Controller?

Have both the expander and the RAID controller. Hooked everything together according to the docs on-line, but no drivers are seen. Can't tell if this is just a compatibility issue, or perhaps a bad ...
3
votes
1answer
555 views

Steady red light on 2 HP SAS drives in RAID 1

I have a HP ProLiant web server with two HP 300GB SAS SFF 2.5 inch drives (Model: HP 507127-B21). Both drives have a solid red light, however there is no indication within the management software that ...
-2
votes
1answer
530 views

Why does a low level format take very long time?

I can write ~100MB/s on a particular 4TB SAS drive when it have a file system on it, but a low level format on this drive took >16 hours. That's ~70kB/s. Since there is not filesystem and only zeroes ...