-1
votes
1answer
59 views

HP ProLiant - Does ILO 2 Advanced offer additional SNMP or IPMI features?

We've got ML350 G5 servers with iLO 2 standard license. Does upgrading to higher iLO license will unlock new SNMP or IPMI data registers? If it will, which ones?
2
votes
0answers
63 views

HP SNMP Traps signalled every 10 seconds for a NIC

I'm trying to setup SNMP traps on my HP DL160 G6 (Xenserver) to notify me whenever I have issues with the server. Following suggestions from this serverfault post, I've installed the HP SNMP agents ...
4
votes
1answer
97 views

HP ProLiant Gen8 Health Agents and EL6.x - cpqHoMibHealthStatusArray has changed to the value: x

I've noticed that my HP ProLiant Gen8 servers report the following message via email to root (or the destination configured in /opt/hp/hp-snmp-agents/cma.conf) upon restart. Trap-ID=11020 ...
0
votes
1answer
319 views

Get port vlan tag via snmp on HP Procurve

I'm trying to write a nagios check that will check if a port is a member of (tagged in) a perticular VLAN. I've discovered the following SNMP location SNMPv2-SMI::mib-2.17.7.1.4.5.1.1.40 for checking ...
0
votes
1answer
117 views

DL360 G2 SNMP drive failure location

I've got this service call with the snmp information provided below, about the drive failing in HP DL360 G2 server: Error log Event Type: Error Event Source: Storage Agents Event Category: Events ...
1
vote
1answer
231 views

HP Network Device Management Software

I look after a network with 11 x new HP v1910 24-port 1GB switches and 2 x HP 4204vl 1GB Chassis switches. I'm looking for software to enable me to: Map the network graphically - there are a lot of ...
1
vote
1answer
1k views

System load by HP-SNMP-Agents is high

After installing the hp-snmp-agents on my proliant server, I noticed the system load never goes below 1. Is this normal behavior, or is it possible to reduce the load of the HP tools? Update: the ...
1
vote
1answer
346 views

hp sim Firmware And Software Revision (how does it get that data)

I have installed all the insight agents, and I have sim showing the Firmware And Software Revision information on the System status screen. Can anyone explain how sim is getting that information from ...
3
votes
1answer
1k views

Installing HP Agents on OpenFiler

We're hoping to solve a need for a low-cost SAN at one of our sites by deploying an OpenFiler on a DL360 strapped to an MSA70. We've been running a similar setup for 18 months at our locel site, so ...
3
votes
1answer
4k views

Getting hp-snmp-agents on HP ProLiant DL360 on Lenny working [duplicate]

Possible Duplicate: System load by HP-SNMP-Agents is high After receiving our HP ProLiant DL360 I'd like to integrate the machine into our Munin system and thus enable ProLiant specific ...
3
votes
3answers
11k views

Does HP's iLO support SNMP polling?

I use Nagios for monitoring my servers and network hardware. Can I poll hardware stats (temp, fan speed, etc) via the iLO 2 management port? How about iLO 100i via the dedicated management port ...
0
votes
2answers
2k views

What is the SNMP OID for the duplex page count on a LaserJet 4000 series printer?

I'm trying to read the number of pages and the number of duplex pages (or the number of sheets and number of impressions, which is equivalent) from a large number of printers via SNMP. The idea is to ...