0
votes
0answers
33 views

SNMPv3 messages not generating

I am new to configuring SNMPV3 on my redhat linux net-snmp. I have made some changes in the /etc/snmp/snmpd.conf file and also added the user with createUser directive in snmptrapd.conf file. The ...
0
votes
0answers
25 views

How can I listen to SNMP Traps v1 and v3 with authentication enabled

I'm having problems setting up the snmptrapd daemon to listen to SNMP v3 traps with authentication and SNMP v1 traps (without authentication, obviously). I know that if I uncomment the ...
0
votes
1answer
112 views

snmpbulkwalk hangs at certain OIDs

While setting up some hosts in Check_MK for SNMP-only monitoring I've found some hosts where snmpbulkwalk appears to 'hang' and then timeout while processing a certain OID. eg: OMD[prod]:~$ ...
1
vote
0answers
31 views

snmpget on IPv6 local address timesout though snmpd is listening on ipv4 and ipv6

I am doing snmpget from a RHEL machine to the localhost. It works for IPv4 and doesn't work for IPv6. # snmpget -v2c -c public udp6:[::1] sysName.0 Timeout: No Response from udp6:[::1]. # snmpget ...
-1
votes
1answer
68 views

How to find SNMP community string?

I've been trying to find the SNMP community string in Ubuntu here, but haven't had much luck. I'm using Ubuntu 12.10 and have followed the instructions here, but my /etc/snmp/snmpd.conf file has ...
1
vote
1answer
105 views

snmpd.conf disk directive dskIndex order

I'm trying to configure snmpd on my CentOS hosts to monitor the free disk usage in percent. If I set snmpd.conf to disk / disk /var , the values can be queries with 1.3.6.1.4.1.2021.9.1.1.1 for ...
1
vote
0answers
89 views

Unable to send v3 trap using snmptrap

I am trying to send snmp v3 trap using snmptrap command on ubuntu 12. I tried: sudo snmptrap -v 3 -c 1 localhost -a MD5 -A abcdefgh -l noAuthNoPriv -u myuser sudo snmptrap -v 3 -c 1 localhost -a MD5 ...
1
vote
1answer
251 views

How does snmpd know where to send a trap?

I'm trying to get my head around our snmpd.conf file in order to begin managing snmp with puppet. The existing file has several alarms setup for things like excessive disk space, load, etc. I'm ...
5
votes
1answer
251 views

SNMP bytes received disagrees with ifconfig

SNMP ifInOctets = 2145342796 - about 2GB. ifconfig: RX bytes:174302710687 (174.3 GB) Interestingly, the sent bytes agree almost perfectly: ifOutOctets: 1002415050 - about 1GB ifconfig: TX ...
3
votes
1answer
5k views

Cacti not working for SNMP data sources

I installed packages cacti and snmpd on a Debian server. I'm able to display common graphs in Cacti (such as memory usage, load average, logged in users, etc) using the data templates listed as Unix. ...
0
votes
1answer
253 views

snmp trap using disman-event mib related issue

notificationEvent ifMtu.1 IF-MIB::ifMtu.1 1.3.6.1.2.1.2.2.1.4.1 monitor -I -u root -s -t -r 18 "Warn: High ipp Usage" -e ifMtu.1 1.3.6.1.2.1.2.2.1.4.1 != The above lines are in my snmpd.conf file ...
3
votes
2answers
3k views

/usr/local/share/snmp/snmpd.conf: line 5: Error: unknown payload OID

using ubuntu with net-snmp snmp work but in sys.log i see a lot of errors about snmpd.conf snmpd.conf: rwcommunity community 10.0.0.1 rwcommunity community 10.0.0.2 agentAddress udp:10.0.0.1:161 ...
0
votes
1answer
1k views

snmp.conf how to allow any remote client

Using linux (Ubuntu) with net-snmp. I want to allow any remote client to execute snmpget. The remote client not have to be from the same subnet , so i cannot do this by define subnet. Now i add line ...
3
votes
1answer
1k views

Can I give my own MIB any OID that I want? Is there a convention to application MIB OID?

I created a scalar MIB for my application, monitor request_queue_size. I followed the write MIB tutorial . The OID there is a long hierarchical OID. I wonder if I can give a short hierarchical OID ...
-5
votes
1answer
1k views

how to instal snmp server in redhat linux?

I am having some problem with snmp server installation.I want to install snmp server and agent also by which i can query to my local host. i have downloaded the snmp tar version as I want to write a ...
0
votes
0answers
315 views

SNMP Disk Monitoring

So I put the following lines in my snmpd.conf: disk / disk /usr disk /localhd I restarted snmpd and tried to do an snmp walk on the following OID: 1.3.6.1.4.1.2021.9.1. What I pasted bellow is just ...
1
vote
1answer
2k views

SNMPD starts without errors but is not listening on any port?

HP ProLiant DL360 G7 running CentOS6 5.7 with Net-SNMP 5.3.2.2-14. I have 7 of these servers in a remote site all running mixture of CentOS 5.7 and RHEL 5.7 with same Net-SNMP installed from RPM. On ...
3
votes
2answers
1k views

Howto prevent snmpd cache results from extend script

On my freebsd box i have snmpd daemon from net-snmp-5.5_4 packet. In snmpd.conf file i have: extend .1.3.6.1.4.1.2021.2 inpt /usr/bin/perl /usr/local/etc/snmp/mpdinput.pl where mpdinput.pl my ...
1
vote
1answer
781 views

How to disable version 1 and version 2c in snmpd?

Because I just use snmp v3 and want to disable version 1 and version 2c in snmpd. How can I do this?
1
vote
1answer
264 views

Will the OID for a custom extend SNMP call be the same on multiple boxes?

CentOS 5.7 | SNMPD This question is a little messy so I apologize in advance for any confusion. I'm using the extend command in /etc/snmp/snmpd.conf to run a script. I later used the snmpwalk ...
1
vote
1answer
927 views

Debian Testing - SNMPD Configuration for Zenoss

Linux server1.xen.prgmr.com 3.0.0-1-686-pae #1 SMP Sat Aug 27 16:41:03 UTC 2011 i686 GNU/Linux snmpd 5.4.3~dfsg-2.3 zenoss-stack 3.2.1-0 I have installed Debian Testing, Zenoss and smpd on the same ...
0
votes
1answer
221 views

Cannot query SNMP agent from hosts in the local network

I'm trying to configure SNMP (net-snmp) daemon on my OpenSuse box. Agent works on 192.168.1.3 address, and I'd like to send requests from other hosts in 192.168.1.0/24 network. My snmpd.conf file has ...
1
vote
1answer
204 views

snmp get value from a file

I've a script getting value in form of 33333 or 23939 etc. i.e. ./script output: 24310 Is there any possibility that i could monitor in nms over snmp by using the above value. If the value is greater ...
0
votes
2answers
4k views

Set up SNMP Trap for disk usage?

I would like to configure snmpd to send traps for disk usage. Currently the file includes these lines: disk /ramdisk ignoreDisk /dev/sda1 ignoreDisk /dev/sda3 disk / 1% load 60 30 15 ...
0
votes
3answers
3k views

How to restart snmpd on Opensolaris after changing snmpd.conf?

I need to restart snmpd after updating /etc/snmp/conf/snmpd.conf, so it recognizes the changes. I'm using Net-SNMP 5.4.2 on Opensolaris 10. I've tried these two: snmpd restart kill -9 pid The ...
1
vote
1answer
289 views

Forwarding SNMP GET requests

I have a cluster of linux servers and a single (gateway) linux server that can access the machines in the cluster by hostname or ip. From outside of the cluster the machines are not accessible by ...
0
votes
1answer
152 views

Automatically adding comments to snmpd.conf

I have a snmpd.conf which looks like this. I would like the comments to auto-fill i.e. make the file human readable with explanations. If it were one file, I could have done copy/paste from default ...
2
votes
3answers
6k views

Finding out why Dell Controller is Degraded

I installed open manage on a couple of my PE 2950s for snmp monitoring of the RAID. All the checks seem to come back okay except for controllerState: [root@aMachine ~]# snmpwalk -v 2c -c ...
1
vote
2answers
994 views

Setup Windows7 To accept snmp requests and forward to my own snmp server

I'm a newbie to snmp. I've written an SNMP server (Based on this open source code). I can succesfully send it get request and receive responses with MIBBrowser locally (on localhost) Next, I tried to ...
2
votes
4answers
9k views

Snmp configuration giving me timeout, no response

This is definitely not a firewall issue as no firewalls are in between the src and tgt machines. I'm simply setting up snmp to be queried by a nagios server. My snmpd.conf looks like the following ...