0
votes
0answers
21 views

SonicWall VLAN Device Redirection

I have a device (Network Attached TV tuner) I use on my X0 VLAN. I have a wireless (W0) device that I would like to be able to access this device on my VLAN. The problem is right now the devices ...
5
votes
2answers
798 views

How do I route a public IP range over an IPSEC VPN?

So, I have an established IPSec Site to Site tunnel. Site A has a SonicWall, Site B has a EdgeRouter. The first tunnel consists of Site A's NATed ips to Site B's NATed ips. Everything works as ...
0
votes
0answers
453 views

Sonicwall NAT Policy Pritory Ordering not working

I understand that the priorities of the NAT Policies for a Sonciwall UTM device (we have an NSA 3500) are automatically assigned - a couple of quotes below from the Admin manual makes that clear "By ...
3
votes
1answer
398 views

Site to site VPN between Cisco VPN Router and Sonicwall NAT issues

I'm trying to establish a site-to-site VPN connection from office to datacenter. Cisco RV042G and SonicWall NSA2400 In the office; we have the subnet 10.0.0.0/24 defined and hosts from 10.0.0.150 to ...
0
votes
1answer
519 views

Routing multiple WAN subnet on a single interface SonicWall NSA 2400

In my current infrastructure I have the following setup : ISP LINK 1 (64.30.24.128/26) ----|X3--sonicwall--X0|----LAN (64.30.24.128/26) X0(LAN) is configured as Mode/IP Assignment: Transparent ...
3
votes
1answer
610 views

Dynamic DNS with split horizon DNS or hairpin NAT

I would like to host a CalDAV and CardDAV server for devices that will roam between being on the LAN to outside my network (such as my iPhone and laptops). A static IP is prohibitively expensive. I ...
1
vote
2answers
1k views

Problems with Hairpin NAT when sharing multiple services on a public IP?

Our Internet line is configured as follows (IP addresses are simplified placeholders, but it's the same layout): Subnet: 192.168.200.0/24 Default gateway: 192.168.200.1 Public ...
0
votes
1answer
615 views

how to setup sonicwall tz210 to port forward packets received from external ip to another external ip

i have a sonicwall tz210 on a fixed ip, say ip1. And then i have, let's say a legacy server, with external ip ip2, which sends data to ip1 (and I have another server on ip1 behind the sonicwall which ...
0
votes
0answers
357 views

How to configure Sonicwall NAT across a P2P T1?

The setup: Location 1 = L1 Location 2 = L2 L1 Computer [192.168.1.2] L1 Sonicwall LAN Interface X0 [192.168.1.1] L1 Sonicwall LAN Interface X2 [10.10.11.1] L1 Adtran T1 Router [10.10.11.2] L2 ...
1
vote
2answers
339 views

Unblocking a blocked TCP port on a Sonicwall Tz170 firewall

Anyone with knowledge of Sonicwall's Tz range might be able to help. Under Firewall >> Service I create a new Service called "remote tcp conn" and add it to a new Service Group. Then under ...
2
votes
2answers
427 views

sonicwall vpn and NAT

I have a site-to-site VPN set up with a vendor. Let's say the tunnel endpoints are 192.1.1.101 on my side and 192.1.2.0/24 on the vendor's side (which get's NATted to their LAN of 10.x.x.x). This is ...
0
votes
1answer
219 views

How can I route some (but not all) web traffice over a VPN tunnel. Sonicwall appliances on each end

I have two networks: Network A Private 10.0.0.0/24 Network B Private 10.0.10.0/24 Both running Sonicwall ~200 appliances, connected by a VPN tunnel. I am able to reach specific internal address on ...
0
votes
1answer
741 views

Two email servers behind Sonicwall unable to communicate with each other

I've been struggling with an issue between two mail servers behind my Sonicwall NSA 2400. Both servers interact with the outside world just fine, but they cannot successfully send e-mail to each ...
1
vote
2answers
3k views

How can I setup a Firewall without NAT?

We have 16 IP addresses from our ISP, and are setting up a SonicWall Firewall. I'd like to have the SonicWall do NAT for the LAN, but act as a firewall only (no NAT) for the servers which are using ...