0
votes
1answer
20 views

Trying to replicate a working IPSec/L2TP config from OpenSWAN to StrongSWAN

I have a working OpenSWAN implementation for RA, using IPsec transport and l2tp for the tunnel, running in AWS. The instance has a private IP, with a public EIP mapped to it. I use the private ip for ...
3
votes
1answer
78 views
+150

TCP connection through IPSec (Linux/Strongswan) stalls after exceeding PMTU

The backups (via Bacula) of one of my servers (“A”) connected via IPSec (Strongswan on Debian testing) to a storage daemon (“B”) don't finish 95% of the times they run. What apparently happens, is: ...
1
vote
0answers
48 views

Windows 7/8 Strongswan IKEv2 Wrong Gateway

I have setup Strongswan on Ubuntu 14.04 from the official package. I use IKEv2 with PKI authentication and a custom authorization plugin. This works great for Android and Ubuntu clients using ...
0
votes
1answer
16 views

Is there a way to use an external program to authenticate XAuth with StrongSwan IPSec?

I'm currently using StrongSwan for my iOS devices to connect. I was wondering if there is a way to use an external program for XAUTH? I currently have the following configuration: : RSA server.pem ...
0
votes
0answers
37 views

vServer: Configuring single (/128) assigned IPv6 addresses for use as IP address pool for IPSEC (Strongswan) road warriors

I've a new (dev) vServer up and running. Unfortunately the provider only hands out single IPv6 addresses (not even /64 subnets). Now I am a bit confused how to achieve the following: I want to use ...
0
votes
1answer
89 views

SSH not working over IPSec tunnel (Strongswan)

I configured a small network on a cloud virtual machine. This virtual machine has a static IP address assigned to eth0 interface that I'll call $EXTIP. mydomain.com points to $EXTIP. Inside, I have ...
1
vote
2answers
338 views

Strongswan (IKEv2) connection established, but no traffic routing

I've seen this sort of question posted a few times before, but so far, none of them have solved my issue. I'm trying to set up an IKEv2 VPN on my Ubuntu Server to use with my Windows Phone using ...
0
votes
1answer
141 views

Strongswan with X.509 authentication and LDAP authorization

I would like to setup Strongswan/Libreswan with PKI authentication. Now I have searched and found only how to configure specific accepted client certificates like here: ...
1
vote
1answer
46 views

Is using EAP-MD5 in strongSwan a security risk?

Quoting Wikipedia: It offers minimal security; the MD5 hash function is vulnerable to dictionary attacks, and does not support key generation, which makes it unsuitable for use with dynamic WEP, ...
0
votes
1answer
584 views

strongSwan setup where both sides are behind NAT

I'm trying to setup a strongSwan server in my home and connect to it from another network. Let's say sun is the VPN server and venus is the client. Both sun and venus are behind NAT networks. sun is ...
0
votes
1answer
77 views

EAP password prompt in strongSwan

I'm trying to setup a host-host configuration using strongSwan. I did manage to set it up using certificates and now I wish to set it up using certificates + EAP authentication. I mixed this ...
1
vote
1answer
173 views

Issues with StrongSwan on FreeBSD 10.0. Charon refuses to start

The charon.log with full debug levels (4) is as follows: Jan 21 16:09:47 00[DMN] Starting IKE charon daemon (strongSwan 5.0.4, FreeBSD 10.0-RELEASE, amd64) Jan 21 16:09:47 00[LIB] plugin 'aes': ...
0
votes
0answers
92 views

StrongSwan / IKE: port 500 packets lost

I have got problems setting up a StrongSwan IpSec network. I use arno-iptables-firewall with the IpSec module and have added rules for NAT and to the routing table. When pinging a host in the remote ...
0
votes
0answers
194 views

IPSec tunnel not working when set up asynchronously

I'm trying to create a tunnel using StrongSwan. In order to do this, I'm creating two sh files, one for each gateway router. All I'm doing in the sh files is creating the tunnel, configuring it, and ...
0
votes
0answers
59 views

No such device error when trying to create IPSec tunnels

I'm trying to establish parallel tunnels between the same two routers, each of which route traffic from slightly different subnets. I can always set up the first tunnel without a problem, however when ...
0
votes
2answers
241 views

Using strongswan, what's the difference between auto=add, and auto=start?

The docs on this are pretty vague, what operation, if any, should be done automatically at IPsec startup. add loads a connection without starting it. route loads a connection and installs kernel ...
0
votes
0answers
358 views

Strongswan ipsec <--> iPhone, can't access LAN

I'm trying to connect to my LAN with iPhone, using Cisco IPsec VPN connection. I can connect to VPN, but I can't access any LAN devices. Hardware/Software: Strongswan 5.0.4, running on router - ...
0
votes
1answer
311 views

StrongSwan + xl2tpd client timeout between 2-5 minutes

I run CentOS 6.4 on Amazon EC2, using xl2tpd-1.3.1 from EPEL repository together with StrongSwan 5.0.4. I setup a simple IPSec connection: conn l2tp type=transport keyexchange=ikev1 ...
2
votes
0answers
111 views

Having trouble installing Racoon and Strongswan on the same system

I have two applications that I need to run, one uses Racoon for establishing IPSec tunnels and the other uses Strongswan. Therefore, I need both Racoon and Strongswan installed simultaneously on my ...
2
votes
1answer
304 views

Simultaneous IKEv1 and IKEv2 connection support in Strongswan

I'm using Strongswan to handle IPsec connections, and need a way to support both Windows (IKEv2) and OS X (IKEv1) clients. I would prefer to use pure IPsec (i.e. avoid having to setup L2TP) unless ...
0
votes
1answer
2k views

strongSwan IKEv2 + Windows 7 Agile VPN: What is causing Error 13801

I have an AWS instance that I want to be a VPN server. It will connect Windows 7 clients to a private network in the Amazon cloud. I have installed Ubuntu 12.04 and the strongswan-ikev2 package. ...
1
vote
2answers
185 views

Windows 8 and SSL's EKU serverAuth flag?

I'm reading this tutorial which says, Your gateway certificate must have: An Extended Key Usage flag explicitly allowing the certificate to be used for authentication purposes. The serverAuth EKU ...
-1
votes
1answer
339 views

strongswan: entirely virtual subnet [closed]

I recently set up a strongswan IPSec VPN to access some non-public services of my home server from my android smartphone. I am using OpenVPN on some other devices for the same task, but chose ...
1
vote
1answer
469 views

strongswan can't push DNS resolver to OSX Mountain Lion (split tunnel)

I'd like to set up an IPSec responder (VPN server) for OSX desktops and laptops. Everything seems to work fine, except I cannot push a DNS server to be used system-wide on the initiator (VPN client). ...
0
votes
2answers
673 views

what does “openssl FIPS mode(0) unavailable” mean?

I compiled and installed strongswan ipsec vpn successfully, as demonstrated by the fact that the service starts successfully: as3:~# ipsec restart Stopping strongSwan IPsec... Starting ...
0
votes
1answer
566 views

Finally get my win 7 connected to strongSwan VPN, but there's no Internet

I believe I've followed all the instructions, and my win 7 did get connected, but there's no Internet. Background: Server OS: ubuntu 12.04 on linode xen VPS strongSwan Version: 4.6.4 ...
1
vote
1answer
1k views

strongSwan IPsec server with AWS EC2 VPC VPN client

I'm trying to create a VPN tunnel between 2 AWS regions. The way I'm trying to do this is by setting up a IPsec server in Linux with strongSwan in one region, and then a VPC VPN in the other region. ...
2
votes
1answer
1k views

strongSwan ipsec setup, couple of questions

i am trying to setup a IPsec bridge between my home network and my office network. I want to use StrongSwan to encrypt the traffic as IPsec i am trying to follow this guide A brief description of ...