Temperature is how hot or cold something is, questions with this tag relate to how different hardware deals with different temperatures and how to maintain it

learn more… | top users | synonyms

0
votes
1answer
30 views

Intel SSB temperature sensor

I have an Intel server motherboard that is reporting an issue with the SSB temperature sensor. I have searched for the acronym but cannot find a definition. What does SSB stand for?
2
votes
1answer
67 views

HP DL380G6: Where is the Temp. Sensor #29 (System Zone)?

The Temp. Sensor #29 of my HP DL380G6 seems to give me a wrong number. It says that the temperature is more than 50C (Caution: 60C, Critical: 65C) while the actual value is 13C. And I think it may be ...
1
vote
1answer
51 views

ipmitool pef temperature soft shutdown

Recently I've had the technicians switch off the cooling system in the server room, without notifying me first. Since the compute nodes do have IPMI cards from different manufacturers installed, I'd ...
0
votes
0answers
39 views

WLAN:Deauth: [MAC] STA reason code=2

I use WIFI temperature loggers which are working just fine. However, at one WLAN Access Point they can't connect and get error messages. Here's what I believe to be relevant information from the ...
2
votes
2answers
294 views

When do Dell PowerEdge servers (R210II and R620) automatically shutdown due to over heating?

I've had a hell of a time trying to find out when and how a Dell PowerEdge server (in my case we have a bunch of R210IIs and R620s with iDRACs) deals with overheating. I don't want to wait for the CPU ...
-1
votes
2answers
65 views

Do all PowerEdge servers have thermal CPU protection?

Cant seem to find anyhting about it. I could test it tho, but a quicky for anyone having the answer. Do all PowerEdge servers have a upper CPU temp limit for shutting down? I'm currently playing with ...
0
votes
1answer
81 views

How to address a recurring low temperature error seen at every boot-up?

After updating to latest controller firmware, I started receiving the following error messages: LSI 2208 ROC: Temperature sensor below error threshold on enclosure 1 Sensors 5 thru 7 Is this ...
2
votes
1answer
145 views

FBDIMM Thermal/TDP Issue

I've got a 2U dual Xeon server with 8x 2GB DDR2 FBdim/ECC ram, on an intel s5000PSL board. It's stable, the ram memtests clean and both CPUs are running cool (35C). Half of the sticks run ~60-65C, ...
1
vote
2answers
131 views

What causes servers to reload or shut down if COLO temperature is around 35C or above?

What causes servers to shut down or reload in case of high temperature? For example Juniper network equipment running Junos OS will halt the routing engine if it's CPU temperature remains above 100C ...
1
vote
0answers
122 views

Dell Poweredge 2950 with E5430 Temperature

So I just picked up a few Poweredge 2950 servers and I have them set up with Windows Server 2012. I installed Core Temp to monitor CPU temperature. One server has a CPU operating temp of the following ...
1
vote
1answer
51 views

Blackout Blind for a server room

Would getting a blackout blind reduce the temperature of my server room? I have already silvered the windows and our aircon is struggling but we are not in a position to be able to replace the aircon ...
0
votes
3answers
143 views

Core temperatures 10 degrees higher in one CPU than another, is this cause for concern? [closed]

We have a new Dell server with a pair of 6-core Xeon 2620s for a total of 12 cores. Using Speedfan/HW Monitor, I notice that the cores associated with one of the CPUs run about 10 degrees hotter ...
0
votes
2answers
131 views

How do I re-enable the IPMI temperature sensors?

I've never had a problem reading temperature sensors with ipmitool on my server, but recently the temperature readings started showing up as disabled: # ipmitool sdr list Temp | disabled ...
0
votes
1answer
289 views

Enabling Temperature Support on LSI MegaRaid Cards

I've got two IBM ServeRAID M5014 SAS/SATA Controller cards in two different machines. One reports drive temperatures, the other does not. I am hopping that it is some type of megacli option that I can ...
3
votes
1answer
1k views

HP DL380 G6: Where is Temperature Sensor 30 (I/O Board Zone)?

In ILO2 firmware 2.15 on my DL380 G6, the Temp 30 sensor (location: I/O Board Zone) indicates 65C and my fans are running at 78% capacity. The Caution level for this zone is 110C, and the Critical ...
0
votes
1answer
165 views

Refresh a specific page in ilo 4

I use iLo 4 for my HP dl380 gen 8. I access iLo webpage using internet explorer 10. (Although I would gladly use another browser if anyone can recommend a better one for iLo access). How can I ...
2
votes
2answers
282 views

Server Room Temperature Monitoring - Where to stick my probes?

I have a small server room approx 7' x 12' with an A/C unit dedicated to this room that is positioned on of the short (7') sides and blows air across the room towards the other short (7') side. The ...
0
votes
3answers
473 views

Graphing temperature over time for HP iLo 4

Server: HP DL380p Gen 8, running latest iLo 4. One sensor, Sensor #25 for the HD Controller, tends to run a bit hot when compared to the other sensors. It tends to read 75 C. Caution temp is 100 C. ...
1
vote
1answer
97 views

cacti : Terminology about ups, room temperature etc

We use cacti for graphing lots of metrics : Windows server related metrics go under a branch called "windows". Unix, Linux and storage metrics go under a branch called "Unix". Switch, firewalls, ...
2
votes
1answer
298 views

Temperature in server room

I was just wondering if anyone had an idea if the following values for a server room are acceptable or what needed to be changed. In the room the temperature is 17c with RH of 38% and Dewpoint of ...
2
votes
1answer
56 views

What to look for in a rack that has to survive extreme conditions

I work for a 2-way radio company, and we're spec'ing out a mountain top digital radio repeater system, that will require a server and a switch setup. What should I be looking for in a rack cabinet ...
0
votes
2answers
832 views

How to check CPU temperature on a HP P2000?

I have an HP StorageWorks MSA Storage P2000 G3 SAS array. show sensor-status gives something like # show sensor-status Sensor Name Value Status ...
0
votes
2answers
769 views

lm-sensors voltage alarms, safe to ignore?

I am building a small NAS server, the motherboards is a Intel D2700MUD (fanless) and the PSU is "Ace Outburst 480W". After installing Ubuntu Server, I installed lm-sensors. The output: ...
1
vote
1answer
251 views

Using grep/regex to get array of temperatures

I'm trying to setup some basic temperature monitoring on my server - (without using third-party tools). I've installed a couple of libraries on my linux box to get sensors working on my server, and ...
6
votes
5answers
5k views

automatically shutting down an ESXi host nightly

We just picked up a new development server that I've loaded ESXi on. The room it's in is well ventilated during the day but at night the door is closed and it gets quite toasty in there. I've been ...
1
vote
2answers
2k views

lm_sensors reports wrong temperature on Supermicro X8DT3?

Here's my system info: System Information Manufacturer: Supermicro Product Name: X8DT3 Version: 1234567890 Serial Number: 1234567890 UUID: 3EFC338F-2038-F257-3B5E-0025902BF938 ...
2
votes
4answers
434 views

Is it possible that hard drive temperature reading is inaccurate by a large margin?

I have a 3 - 4 year old 250GB WD hard drive that has shown abnormally high temperature readings ever since I bought it. The temperatures were so much higher than expected that I ended up attributing ...
1
vote
1answer
630 views

linux kernel 3.0.0 i7 CPU overheats and locks up

The server with i7 CPU (Intel(R) Core(TM) i7 CPU 950 @ 3.07GHz) under linux kernel 3.0.0 (3.0.0-10-server) generally works properly, but when it is put under heavy load - it overheats (as shown by ...
2
votes
5answers
2k views

What temperature monitoring software is avalible for Server 2003, 2008 and 2008 R2?

I don't have much experience working with servers and I need to monitor temperatures for several servers (remotely). I use hwmonitor for my laptops but it doesn't support server hardware. Does anyone ...
1
vote
4answers
779 views

Monitor Dell thermal sensors in FreeBSD?

I'm trying to remotely monitor temperature sensors within two Dell PowerEdge 6850's. I have a fear that the building we are in is turning off the air conditioning on the weekends to save power, which ...
5
votes
4answers
4k views

Maximum safe hard drive temperature?

I have two new-ish 1TB hard drives in my server, both running at 38 degrees C at the moment. Should I be worried?
0
votes
2answers
180 views

When to add air conditioners [duplicate]

Possible Duplicate: What is the correct temperature for a server room? We're a small company with a 200 foot back room we use as a server room. It has no fans and no ventilation. Right ...
0
votes
1answer
166 views

OSX: Watching tempeture trends based on Ambient Tempeture

So I noticed a temperature monitor cleverly labeled "Ambient." Knowing that the sensor is inside my computer, I can get a decent temperature check on my overly hot dorm room if I check it as soon as I ...
1
vote
1answer
3k views

PowerShell Script to Gather System Temperature

Does anyone have a PowerShell Script they use to gather system temperature information? This is not to replace external sensors, just another way to monitor the health of a system from a temperature ...
2
votes
1answer
626 views

Standard Operating Temperature Range for Xserve PSUs

We use Lithium for network monitoring. For Xserves, by default it throws an alert when the PSU temperature goes above 65°C. Lately, we've been getting multiple alerts a day with the temperature ...
5
votes
3answers
1k views

Server Room Temperature Control - Does anyone have a similar setup?

Our Server room is located in the middle of our building and has no access to a window or outside ventilation. I had a quote done by a local heating/air conditioning company to install a room specific ...
7
votes
6answers
351 views

Computer controlled winch

It was a long time coming but I've just had AC installed in my server room. I've also purchased a MiniGoose II from ITWatchDogs which I can't say enough about. So I'm covered by cooling, and I'll be ...
3
votes
4answers
1k views

How to monitor the temperature of a switch?

Is there any application that give me the temperature of each switches on my network?
3
votes
3answers
3k views

How to check CPU/HDD temperature under XenServer 5.6?

Is it possible to check the temperature of the CPU and locally attached SATA/IDE HDDs under XenServer 5.6? Can I install lm-sensors?
1
vote
0answers
565 views

LM Sensors always returning same (invalid) value for one temp sensor

I am trying to monitor the temp sensors on a server, and plot them using Cacti. I have lm-sensors installed and working correctly. For example, here is the output from sensors: % sensors ...
1
vote
3answers
165 views

Monitor temperatures in a PC

I'm experimenting with different locations and fans in my server. Whats a good program to monitor temperatures?
1
vote
2answers
154 views

Hot video card in server

Not sure if this belongs here or Superuser (I looked at Superuser -- suspect there are more hardware gurus here). I have a server that sits in a cabinet. It's connected to a small screen that is ...
2
votes
2answers
10k views

How to monitor the temperature of a HP Procurve 3500 switch via SNMP

I am attempting to poll the temperature of an HP ProCurve 3500YL switch remotely using SNMP. Looking at this MIB, it appears that the following OIDs: hpCpuTemperature ...
1
vote
1answer
1k views

How can I monitor a Smart-UPS 2200 in PRTG?

This UPS is connected via a serial cable to a server. I am trying to get the temperature readings off of the sensor that is connected to the UPS and get them in PRTG. We were able to do this in the ...
2
votes
4answers
752 views

SNMP-capable temperature probes [closed]

I'm looking for a SNMP temperature monitoring solution to put into my racks. Idealy this thingy would be an ethernet device with SNMP capability. I'd like to put two of these probes as top of rack and ...
0
votes
3answers
177 views

fedora halt - not sure why

Got a brand new server (IBM x3500) yesterday, installed Fedora 12 on it and thought we'd run some code to see how it performs. After around 7 hours of running, the system seems to have halted. The ...
4
votes
4answers
3k views

LSI MegaRaid - get HDD temperature

Is there any way to get a drive temperature using MegaCLI or any other utility? Like "tw_cli /cx/px show temperature" in 3ware. OS: Solaris x86.
2
votes
2answers
104 views

Hard freezes and reboots when compiling

One of our workstations has begun to freeze or reset under some circunstances. We can reproduce this in both Linux and Windows so it's most likely a hardware issue. The freezes most usually happen ...
1
vote
3answers
3k views

Nagios & Temperature

I'm currently running Nagios 3 on Linux, with Windows clients using NSClient++. The Windows clients (8) will be put into a hot humid environment. I have all the basic checks working for CPU, RAM, etc ...
2
votes
6answers
11k views

automatic get server temperature via HP iLO

I have a couple of HP servers in 2 offices. They have iLO interfaces and i can read the temperature from there. How can i read this temperature automaticaly over the network ? does iLO have any sort ...