1
vote
1answer
574 views

Unable to make work both private and public ip network on openvz container in Proxmox

I'm using Proxmox 3, it is a fresh installation. For those who know, I'm using OVH Vrack 1.5 (along with a previous Vrack 1.0). My server has two interface eth0 and eth1, I succeeded to configure ...
1
vote
0answers
403 views

debian KVM - network bonding fails with vlan and bridge

i have a Debian 6 system configured with 2 NICs these NICs are used on a bond (bond0) which is used by bridge that require to use VLAN. i can get connection between guests running on VLAN10 but it ...
0
votes
1answer
202 views

Multiple VLANs - how Linux / Debian process packets

I can't find answer about how linux processes incoming packets from different VLANs, that do not belong to a subnet assigned to a VLAN. Imagine this situation. On Linux machine with the following ...
0
votes
1answer
210 views

Debian Network boot with a VLAN (DHCP + TFTP)

I've been given 34 servers (HP Proliant) to use for HPC. Due to the server owners' request, 33 of these will need to act as diskless thick clients, and one will act as DHCP and TFTP server to enable ...
0
votes
1answer
2k views

routing through multiple subinterfaces in debian

my question is as simple as the title, i have a debian 6 , 2 NICs, 3 different subnets in a single interface, just like this: auto eth0 iface eth0 inet static address 192.168.106.254 ...
0
votes
1answer
395 views

vlans broadcast works but ping doesn't

i have a server with ESX5, have a Standar Switch(vswitch1) with one physical NIC attached, vswitch1 VLAN ID is set to All(4095) so it can see traffic on any VLAN, connected to vswitch1 i have 2 VM, ...
1
vote
1answer
164 views

esx5 debian VM vlan setup

i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass ...
2
votes
1answer
151 views

Access to WAN from one VLAN

i want to create a VLAN for 3 guest VMs. I already have it and every VM can ping each other, but the problem is that any guest CAN NOT have access to Internet Network configuration in Host machine # ...
2
votes
1answer
732 views

How to add vlan without vconfig command? [closed]

Is there any way how to create vlan interface without using vconfig ? I have only KVM console and trunk port connected to the machine, so I cannot use apt as I do not have internet access. I defined ...
3
votes
4answers
276 views

Arbitrary VLAN interface name

Is there a way to name a VLAN interface arbitrarily like eth72 or ext19 instead of the four standard nameing schemes eth0.72, vlan19 (and the padded variations)? Don't have no clue. Perhaps udev?
3
votes
2answers
2k views

Debian: Should I add vlan interface into bridge for KVM?

I am setting up a Debian Squeeze box as a KVM host. I want to add multiple interfaces to each KVM guest so I want them to be on different VLANs. After reading about this, I believe the best method is ...
3
votes
1answer
797 views

vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that ...
1
vote
1answer
560 views

iscsitarget and vlans (Debian Squeeze)

We are currently running iscsi in an open network and would like to migrate our iscsi to a separate vlan. Reading through the documentation this doesn't seem to be possible. Instead iet/iscsitarget ...
0
votes
1answer
1k views

Bridging a vlan and OpenVPN tap on Debian

Under Debian I need to bridge a vlan eth0.1 and tap tap0. Usually, when bridging a normal ethernet adapter with a tap I would include something along the lines of this in /etc/network/interfaces: ...